Home » Seagate Manuals » Hard Drives » Seagate ST3146854FC » Manual Viewer

Seagate ST3146854FC Cheetah 15K.4 FC Product Manual - Page 37

Physical/electrical specifications

View all Seagate ST3146854FC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

6.0 Physical/electrical specifications This section provides information relating to the physical and electrical characteristics of the drive. 6.1 None. AC power requirements 6.2 DC power requirements The voltage and current requirements for a single drive are sh'own below. Values indicated apply at the drive connector. Table 2: DC power requirements for operation in 2Gb mode ST3146854FC Notes (Amps) (Amps) Voltage +5V +12V [2] Regulation [5] ±5% ±5% [2] Avg idle current DCX [1] [7] 0.94 0.78 Maximum starting current (peak DC) DC 3σ [3] 1.07 1.91 (peak AC) AC 3σ [3] 1.36 3.87 Delayed motor start (max) DC 3σ [1] [4] 0.60 0.03 Peak operating current: Typical DCX [1] [6] 1.03 1.18 Maximum DC 3σ [1] 1.04 1.19 Maximum (peak) DC 3s 1.56 2.84 ST373454FC (Amps) (Amps) +5V +12V [2] ±5% ±5% [2] 0.92 0.57 1.08 1.88 1.44 3.98 0.59 0.03 1.01 1.00 1.03 1.02 2.00 2.78 ST336754FC (Amps) (Amps) +5V +12V [2] ±5% ±5% [2] 0.94 0.43 1.08 1.58 1.37 3.30 0.59 0.03 0.99 0.88 1.00 0.88 2.02 2.54 [1] Measured with average reading DC ammeter. Instantaneous +12V current peaks will exceed these values. Power supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient. [2] For +12 V, a -10% tolerance is allowed during initial spindle start but must return to ±5% before reaching 15000 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator. [3] See +12V current profile in Figure 2. [4] This condition occurs when the Motor Start option is enabled and the drive has not yet received a Start Motor command. [5] See paragraph 6.2.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response. [6] Operating condition is defined as random 8 block reads at 309 I/Os per second for ST3146854FC and Cheetah 15K.4 FC Product Manual, Rev. C 25

Section	Page
1.0 Scope	13
2.0 Applicable standards and reference documentation	15
2.1 Standards	15
2.1.1 Electromagnetic compatibility	15
2.1.1.1 Electromagnetic susceptibility	15
2.1.2 Electromagnetic compliance	16
2.2 Reference documents	17
3.0 General description	19
3.1 Standard features	20
3.2 Media description	20
3.3 Performance	21
3.4 Reliability	21
3.5 Formatted capacities	21
3.5.1 Programmable drive capacity	21
3.6 Factory-installed accessories	22
3.7 Factory-installed options	22
3.8 User-installed accessories	22
4.0 Performance characteristics	23
4.1 Internal drive characteristics	23
4.2 Seek performance characteristics	23
4.2.1 Access time	23
4.2.2 Format command execution time (minutes)	24
4.2.3 General performance characteristics	24
4.3 Start/stop time	24
4.4 Prefetch/multi-segmented cache control	24
4.5 Cache operation	25
4.5.1 Caching write data	26
4.5.2 Prefetch operation	26
4.5.3 Optimizing cache performance for desktop and server applications	27
5.0 Reliability specifications	29
5.1 Error rates	29
5.1.1 Recoverable Errors	29
5.1.2 Unrecoverable Errors	29
5.1.3 Seek errors	30
5.1.4 Interface errors	30
5.2 Reliability and service	30
5.2.1 Mean time between failure (MTBF)	30
5.2.2 Preventive maintenance	30
5.2.3 Hot plugging the drive	31
5.2.4 S.M.A.R.T.	31
5.2.5 Thermal monitor	32
5.2.6 Drive Self Test (DST)	33
5.2.6.1 DST failure definition	33
5.2.6.2 Implementation	34
5.2.6.2.1 State of the drive prior to testing	34
5.2.6.2.2 Invoking DST	34
5.2.6.2.3 Short and extended tests	34
5.2.6.2.4 Log page entries	35
5.2.6.2.5 Abort	35
5.2.7 Product warranty	35
6.0 Physical/electrical specifications	37
6.1 AC power requirements	37
6.2 DC power requirements	37
6.2.1 Conducted noise immunity	38
6.2.2 Power sequencing	38
6.2.3 Current profiles	38
6.3 Power dissipation	42
6.4 Environmental limits	44
6.4.1 Temperature	44
6.4.2 Relative humidity	45
6.4.3 Effective altitude (sea level)	45
6.4.4 Shock and vibration	45
6.4.4.1 Shock	45
6.4.4.2 Vibration	48
6.4.5 Air cleanliness	48
6.4.6 Corrosive environment	48
6.4.7 Acoustics	49
6.4.8 Electromagnetic susceptibility	49
6.5 Mechanical specifications	50
7.0 Defect and error management	51
7.1 Drive internal defects/errors	51
7.2 Drive error recovery procedures	51
7.3 FC-AL system errors	53
7.4 Background Media Scan	53
7.4.1 Media Pre-Scan	54
8.0 Installation	55
8.1 Drive ID/option selection	55
8.2 LED connections	56
8.2.1 J6 connector requirements	57
8.3 Drive orientation	57
8.4 Cooling	57
8.5 Drive mounting	58
8.6 Grounding	58
9.0 Interface requirements	59
9.1 FC-AL features	59
9.1.1 Fibre Channel link service frames	59
9.1.2 Fibre Channel task management functions	60
9.1.3 Fibre Channel task management responses	60
9.1.4 Fibre Channel port login	61
9.1.5 Fibre Channel port login accept	62
9.1.6 Fibre Channel Process Login	62
9.1.7 Fibre Channel Process Login Accept	63
9.1.8 Fibre Channel fabric login	63
9.1.9 Fibre Channel fabric accept login	64
9.1.10 Fibre Channel Arbitrated Loop options	65
9.2 Dual port support	65
9.3 SCSI commands supported	66
9.3.1 Inquiry data	70
9.3.2 Mode Sense data	70
9.4 Miscellaneous operating features and conditions	75
9.5 FC-AL physical interface	76
9.5.1 Physical characteristics	76
9.5.1.1 Physical description	76
9.5.2 Connector requirements	77
9.5.3 Electrical description	78
9.5.4 Pin descriptions	78
9.5.5 FC-AL transmitters and receivers	79
9.5.6 Power	79
9.5.7 Fault LED Out	79
9.5.8 Active LED Out	79
9.5.9 Enable port bypass signals	80
9.5.10 Motor start controls	80
9.5.11 SEL_6 through SEL_0 ID lines	80
9.5.11.1 Parallel Enclosure Services Interface (ESI)	81
9.5.12 Device control codes	83
9.6 Signal characteristics	83
9.6.1 TTL input characteristics	83
9.6.2 LED driver signals	84
9.6.3 Differential PECL output	84
9.6.4 Differential PECL input	84
10.0 Seagate Technology support services	87
Numerics	93
A	93
B	93
C	93
D	94
E	94
F	94
G	95
H	95
I	95
J	95
L	95
M	95
N	96
O	96
P	96
Q	97
R	97
S	97
T	98
U	98
V	98
W	98
X	98

Match case Limit results 1 per page

Cheetah 15K.4 FC Product Manual, Rev. C

6.0

Physical/electrical specifications

This section provides information relating to the physical and electrical characteristics of the drive.

6.1

AC power requirements

None.

6.2

DC power requirements

The voltage and current requirements for a single drive are sh‘own below. Values indicated apply at the drive

connector.

[1]

Measured with average reading DC ammeter. Instantaneous +12V current peaks will exceed these val-

ues. Power supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient.

[2]

For +12 V, a –10% tolerance is allowed during initial spindle start but must return to ±5% before reaching

15000 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been

completed and that the drive is able to accept selection by the host initiator.

[3]

See +12V current profile in Figure 2.

[4]

This condition occurs when the Motor Start option is enabled and the drive has not yet received a Start

Motor command.

[5]

See paragraph 6.2.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and

transient response.

[6]

Operating condition is defined as random 8 block reads at 309 I/Os per second for ST3146854FC and

Table 2:

DC power requirements for operation in 2Gb mode

Notes

ST3146854FC

ST373454FC

ST336754FC

(Amps)

Voltage

+5V

+12V [2]

+5V

+12V [2]

+5V

+12V [2]

Regulation

[5]

±5%

±5% [2]

±5%

±5% [2]

±5%

±5% [2]

Avg idle current DCX

[1] [7]

0.94

0.78

0.92

0.57

0.94

0.43

Maximum starting current

(peak DC) DC

[3]

1.07

1.91

1.08

1.88

1.08

1.58

(peak AC) AC

[3]

1.36

3.87

1.44

3.98

1.37

3.30

Delayed motor start (max) DC

[1] [4]

0.60

0.03

0.59

0.03

0.59

0.03

Peak operating current:

Typical DCX

[1] [6]

1.03

1.18

1.01

1.00

0.99

0.88

Maximum DC

[1]

1.04

1.19

1.03

1.02

1.00

0.88

Maximum (peak) DC

1.56

2.84

2.00

2.78

2.02

2.54