Home » Seagate Manuals » Hard Drives » Seagate ST336754SS » Manual Viewer

Seagate ST336754SS Cheetah 15K.4 SAS Product Manual - Page 41

Power dissipation

UPC - 000064845289

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

6.3 Power dissipation ST3146854SS in 3 Gbit operation Typical power dissipation under idle conditions in 3Gb operation is 14.34 watts (48.93 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Amperes 1.800 1.600 1.400 1.200 1.000 0.800 0.600 0.400 0.0 ST3146854SS DC CURRENT/POWER vs THROUGHPUT (3 Gbit) Random 8 Block Reads 20.00 18.00 16.00 14.00 12.00 10.00 8.00 6.00 4.00 50.0 100.0 150.0 200.0 250.0 300.0 350.0 400.0 I/Os per Second Power (watts) 5Vo lt A 12 Vo lt A Watts Figure 8. ST3146854SS (3 Gbit) DC current and power vs. input/output operations per second ST3146854SS in 1.5 Gbit operation Typical power dissipation under idle conditions in 1.5 Gbit operation is 14.64 watts (49.96 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Amperes 1.800 1.600 1.400 1.200 1.000 0.800 0.600 0.400 0.0 ST3146854SS DC CURRENT/POWER vs THROUGHPUT (1.5 Gbit) Random 8 Block Reads 20.00 18.00 16.00 14.00 12.00 10.00 8.00 6.00 4.00 50.0 100.0 150.0 200.0 250.0 300.0 350.0 400.0 I/Os per Second Power (watts) 5Vo lt A 12 Vo lt A Watts Figure 9. ST3146854SS (1.5 Gbit) DC current and power vs. input/output operations per second Cheetah 15K.4 SAS Product Manual, Rev. B 31

Section	Page
1.0 Scope	11
2.0 Standards, compliance and reference documents	13
2.1 Standards	13
2.1.1 Electromagnetic compatibility	13
2.1.1.1 Electromagnetic susceptibility	13
2.2 Compliance	14
2.2.1 Electromagnetic compliance	14
2.3 Reference documents	15
3.0 General description	17
3.1 Standard features	18
3.2 Media description	18
3.3 Performance	18
3.4 Reliability	19
3.5 Formatted capacities	19
3.6 Programmable drive capacity	19
3.7 Factory-installed accessories	19
3.8 Factory-installed options	20
3.9 User-installed accessories	20
4.0 Performance characteristics	21
4.1 Internal drive characteristics	21
4.2 Seek performance characteristics	21
4.2.1 Access time	21
4.2.2 Format command execution time (minutes)	22
4.2.3 General performance characteristics	22
4.3 Start/stop time	22
4.4 Prefetch/multi-segmented cache control	23
4.5 Cache operation	23
4.5.1 Caching write data	24
4.5.2 Prefetch operation	24
4.5.3 Optimizing cache performance for desktop and server applications	25
5.0 Reliability specifications	27
5.1 Error rates	27
5.1.1 Recoverable Errors	27
5.1.2 Unrecoverable Errors	27
5.1.3 Seek errors	28
5.1.4 Interface errors	28
5.2 Reliability and service	28
5.2.1 Annualized Failure Rate (AFR)	28
5.2.2 Preventive maintenance	28
5.2.3 Hot plugging the drive	28
5.2.4 S.M.A.R.T.	29
5.2.5 Thermal monitor	30
5.2.6 Drive Self Test (DST)	31
5.2.6.1 DST failure definition	31
5.2.6.2 Implementation	31
5.2.6.2.1 State of the drive prior to testing	32
5.2.6.2.2 Invoking DST	32
5.2.6.2.3 Short and extended tests	32
5.2.6.2.4 Log page entries	32
5.2.6.2.5 Abort	33
5.2.7 Product warranty	33
6.0 Physical/electrical specifications	35
6.1 AC power requirements	35
6.2 DC power requirements	35
6.2.1 Conducted noise immunity	37
6.2.2 Power sequencing	37
6.2.3 Current profiles	37
6.3 Power dissipation	41
6.4 Environmental limits	44
6.4.1 Temperature	44
6.4.2 Relative humidity	45
6.4.3 Effective altitude (sea level)	45
6.4.4 Shock and vibration	45
6.4.4.1 Shock	45
6.4.4.2 Vibration	47
6.4.5 Air cleanliness	47
6.4.6 Corrosive environment	47
6.4.7 Acoustics	48
6.4.8 Electromagnetic susceptibility	48
6.5 Mechanical specifications	48
7.0 Defect and error management	49
7.1 Drive internal defects/errors	49
7.2 Drive error recovery procedures	49
7.3 SAS system errors	50
8.0 Installation	51
8.1 Drive orientation	51
8.2 Cooling	52
8.3 Drive mounting	53
8.4 Grounding	53
9.0 Interface requirements	55
9.1 SAS features	55
9.1.1 task management functions	55
9.1.2 task management responses	55
9.2 Dual port support	56
9.3 SCSI commands supported	57
9.3.1 Inquiry data	61
9.3.2 Mode Sense data	61
9.3.2.1 ST3146854SS Mode Sense data	63
9.3.2.2 ST373454SS Mode Sense data	64
9.3.2.3 ST336754SS Mode Sense data	65
9.4 Miscellaneous operating features and conditions	66
9.4.1 SAS physical interface	67
9.4.2 Physical characteristics	69
9.4.3 Connector requirements	69
9.4.4 Electrical description	70
9.4.5 Pin descriptions	70
9.4.6 SAS transmitters and receivers	71
9.4.7 Power	71
9.5 Signal characteristics	71
9.5.1 Ready LED Out	71
9.5.2 Differential signals	72
9.5.2.1 Eye masks	72
9.5.2.1.1 Eye masks overview	72
9.5.2.1.2 Receive eye mask	73
9.5.2.1.3 Jitter tolerance masks	73
9.5.2.2 Transmitter signal characteristics	75
9.5.2.3 Receiver signal characteristics	76
9.5.2.3.1 Jitter	76
9.5.2.3.2 Receiver jitter tolerance	77
9.5.2.3.3 Compliant jitter test pattern (CJTPAT)	77
9.5.2.3.4 Impedance specifications	77
9.5.2.4 Electrical TxRx connections	78
9.5.2.4.1 Transmitter characteristics	78
9.5.2.5 Receiver characteristics	81
10.0 Seagate Technology support services	83
Numerics	89
A	89
B	89
C	89
D	89
E	89
F	90
G	90
H	90
I	90
J	90
L	90
M	90
N	91
O	91
P	91
Q	91
R	91
S	91
T	92
U	92
V	92
W	92

Match case Limit results 1 per page

Cheetah 15K.4 SAS Product Manual, Rev. B

6.3

Power dissipation

ST3146854SS in 3 Gbit operation

Typical power dissipation under idle conditions in 3Gb operation is 14.34 watts (48.93 BTUs per hour).

To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure

8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5

volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by

3.4123.

Figure 8.

ST3146854SS (3 Gbit) DC current and power vs. input/output operations per second

ST3146854SS in 1.5 Gbit operation

Typical power dissipation under idle conditions in 1.5 Gbit operation is 14.64 watts (49.96 BTUs per hour).

To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure

8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5

volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by

3.4123.

Figure 9.

ST3146854SS (1.5 Gbit) DC current and power vs. input/output operations per second

ST3146854SS DC CURRENT/POWER vs THROUGHPUT (3 Gbit)

Random 8 Block Reads

0.400

0.600

0.800

1.000

1.200

1.400

1.600

1.800

0.0

50.0

100.0

150.0

200.0

250.0

300.0

350.0

400.0

I/Os per Second

Amperes

4.00

6.00

8.00

10.00

12.00

14.00

16.00

18.00

20.00

Power (watts)

5Volt A

12 Vo lt A

Watts

ST3146854SS DC CURRENT/POWER vs THROUGHPUT (1.5 Gbit)