Home » Seagate Manuals » Hard Drives » Seagate ST373405LW » Manual Viewer

Seagate ST373405LW Product Manual - Page 20

Cheetah 73LP Product Manual, Rev. C, Ultra2 SCSI, Ultra3 SCSI, Notes for Start/stop

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

10 Cheetah 73LP Product Manual, Rev. C SCSI interface data transfer rate (asynchronous): Maximum instantaneous one byte wide Maximum instantaneous two bytes wide 5.0 Mbytes/sec [4] 10.0 Mbytes/sec [4] Synchronous formatted transfer rate On narrow (8-bit) bus in LVD mode On wide (16-bit) bus in LVD mode Ultra2 SCSI 5.0 to 40 Mbytes/sec 5.0 to 80 Mbytes/sec Ultra3 SCSI 5.0 to 80 Mbytes/sec 5.0 to 160 Mbytes/sec Sector Sizes: Default 512 byte user data blocks Variable 512 to 4,096 bytes per sector in even number of bytes per sector. If n (number of bytes per sector) is odd, then n-1 will be used. Read/write consecutive sectors on a track Yes Flaw reallocation performance impact (for flaws reallocated at format time using the spare sectors per sparing zone reallocation scheme.) Negligible Average rotational latency 2.99 msec Notes for Section 4.2. [1] Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect). [2] Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as measured on a representative sample of drives. [3] Assumes no errors and no sector has been relocated. [4] Assumes system ability to support the rates listed and no cable loss. [5] Access time = controller overhead + average seek time. Access to data = controller overhead + average seek time + latency time. 4.3 Start/stop time After DC power at nominal voltage has been applied, the drive becomes ready within 20 seconds if the Motor Start Option is disabled (i.e. the motor starts as soon as the power has been applied). If a recoverable error condition is detected during the start sequence, the drive executes a recovery procedure which may cause the time to become ready to exceed 20 seconds. During spin up to ready time the drive responds to some commands over the SCSI interface in less than 3 seconds after application of power. Stop time is less than 30 seconds from removal of DC power. If the Motor Start Option is enabled, the internal controller accepts the commands listed in the SCSI Interface Product Manual less than 3 seconds after DC power has been applied. After the Motor Start Command has been received the drive becomes ready for normal operations within 20 seconds typically (excluding an error recovery procedure). The Motor Start Command can also be used to command the drive to stop the spindle (see SCSI Interface Product Manual, part number 75789509). There is no power control switch on the drive. 4.4 Prefetch/multi-segmented cache control The drive provides prefetch (read look-ahead) and multi-segmented cache control algorithms that in many cases can enhance system performance. "Cache" as used herein refers to the drive buffer storage space when it is used in cache operations. To select prefetch and cache features the host sends the Mode Select command with the proper values in the applicable bytes in Mode Page 08h (see the SCSI Interface Product Manual). Prefetch and cache operation are independent features from the standpoint that each is enabled and disabled independently via the Mode Select command. However, in actual operation the prefetch feature overlaps cache operation somewhat as is noted in Section 4.5.1 and 4.5.2. All default cache and prefetch Mode parameter values (Mode Page 08h) for standard OEM versions of this drive family are given in Tables 7.

Section	Page
Contents	7
1.0 Scope 1	7
2.0 Applicable standards and reference documentation 3	7
2.1 Standards 3	7
2.1.1 Electromagnetic compatibility 3	7
2.1.2 Electromagnetic susceptibility 3	7
2.2 Electromagnetic compliance 3	7
2.3 Reference documents 4	7
3.0 General description 5	7
3.1 Standard features 7	7
3.2 Media characteristics 7	7
3.3 Performance 7	7
3.4 Reliability 7	7
3.5 Unformatted and formatted capacities 8	7
3.6 Programmable drive capacity 8	7
3.7 Factory installed accessories 8	7
3.8 Options (factory installed) 8	7
3.9 Accessories (user installed) 8	7
4.0 Performance characteristics 9	7
4.1 Internal drive characteristics (transparent to user) 9	7
4.2 SCSI performance characteristics (visible to user) 9	7
4.2.1 Access time 9	7
4.2.2 Format command execution time (minutes) 9	7
4.2.3 Generalized performance characteristics 9	7
4.3 Start/stop time 10	7
4.4 Prefetch/multi-segmented cache control 10	7
4.5 Cache operation 11	7
4.5.1 Caching write data 11	7
4.5.2 Prefetch operation 12	7
4.5.3 Optimizing cache performance for desktop and server applications 12	7
5.0 Reliability specifications 13	7
5.1 Error rates 13	7
5.1.1 Environmental interference 13	7
5.1.2 Read errors 13	7
5.1.3 Write errors 13	7
5.1.4 Seek errors 13	7
5.2 Reliability and service 14	7
5.2.1 Mean time between failure (MTBF) 14	7
5.2.2 Preventive maintenance 14	7
5.2.3 Service life 14	7
5.2.4 Service philosophy 14	7
5.2.5 Service tools 14	7
5.2.6 Hot plugging Cheetah 73LP disc drives 15	7
5.2.7 S.M.A.R.T. 15	7
5.2.8 Drive Self Test (DST) 16	7
5.2.9 Product warranty 19	7
6.0 Physical/electrical specifications 21	7
6.1 AC power requirements 21	7
6.2 DC power requirements 21	7
6.2.1 Conducted noise immunity 22	7
6.2.2 Power sequencing 22	7
6.2.3 12 V - Current profile 22	7
6.3 Power dissipation 25	7
6.4 Environmental limits 27	7
6.4.1 Temperature 27	8
6.4.2 Relative humidity 27	8
6.4.3 Effective altitude (sea level) 28	8
6.4.4 Shock and vibration 28	8
6.4.5 Air cleanliness 30	8
6.4.6 Acoustics 30	8
6.4.7 Electromagnetic susceptibility 30	8
6.5 Mechanical specifications 31	8
7.0 Defect and error management 33	8
7.1 Drive internal defects 33	8
7.2 Drive error recovery procedures 33	8
7.3 SCSI systems errors 34	8
8.0 Installation 35	8
8.1 Drive ID/option select header 35	8
8.1.1 Notes for Figures 15, 16, and 17. 38	8
8.1.2 Function description 39	8
8.2 Drive orientation 40	8
8.3 Cooling 40	8
8.4 Drive mounting 41	8
8.5 Grounding 41	8
9.0 Interface requirements 43	8
9.1 General description 43	8
9.2 SCSI interface messages supported 43	8
9.3 SCSI interface commands supported 44	8
9.3.1 Inquiry Vital Product data 47	8
9.3.2 Mode Sense data 48	8
9.4 SCSI bus conditions and miscellaneous features supported 51	8
9.5 Synchronous data transfer 52	8
9.5.1 Synchronous data transfer periods supported 52	8
9.5.2 REQ/ACK offset 52	8
9.6 Physical interface 52	8
9.6.1 DC cable and connector 52	8
9.6.2 SCSI interface physical description 54	8
9.6.3 SCSI interface cable requirements 54	8
9.6.4 Mating connectors 55	8
9.7 Electrical description 63	8
9.7.1 Multimode—SE and LVD alternatives 63	8
9.8 Terminator requirements 65	8
9.9 Terminator power 65	8
9.10 Disc drive SCSI timing 66	8
9.11 Drive activity LED 67	8
10.0 Seagate Technology support services 69	8
Figure 1. Cheetah 73LP family drive (ST373405LW shown) 1	9
Figure 2. Cheetah 73LP family drive 6	9
Figure 3. Typical ST373405 drive +12 V current profile 22	9
Figure 4. Typical ST336605 drive +12 V current profile 23	9
Figure 5. Typical ST373405 drive +5 V current profile 23	9
Figure 6. Typical ST336605 drive +5 V current profile 24	9
Figure 7. ST373405 DC current and power vs. input/output operations per second (SE) 25	9
Figure 8. ST373405 DC current and power vs. input/output operations per second (LVD) 25	9
Figure 9. ST336605 DC current and power vs. input/output operations per second (SE) 26	9
Figure 10. ST336605 DC current and power vs. input/output operations per second (LVD) 26	9
Figure 11. Location of the HDA Temperature check point 27	9
Figure 12. Recommended mounting 29	9
Figure 13. ST373405LW mounting configuration dimensions 31	9
Figure 14. ST373405LC mounting configuration dimensions 32	9
Figure 15. J6 jumper header 36	9
Figure 16. J5 jumper header (on LW models only) 37	9
Figure 17. J2 option select header 38	9
Figure 18. Air flow (suggested) 40	9
Figure 19. LW model drive physical interface (68-pin J1 SCSI I/O connector) 53	9
Figure 20. LC model drive physical interface (80-pin J1 SCSI I/O connector) 53	9
Figure 21. SCSI daisy chain interface cabling for LW drives 56	9
Figure 22. Nonshielded 68 pin SCSI device connector used on LW drives 57	9
Figure 23. Nonshielded 80 pin SCSI “SCA-2” connector, used on LC drives 58	9
Figure 24. LVD output signals 64	9
Figure 25. Typical SE-LVD alternative transmitter receiver circuits 64	9
1.0 Scope	11
2.0 Applicable standards and reference documentation	13
2.1 Standards	13
2.1.1 Electromagnetic compatibility	13
2.1.2 Electromagnetic susceptibility	13
2.2 Electromagnetic compliance	13
2.3 Reference documents	14
3.0 General description	15
3.1 Standard features	17
3.2 Media characteristics	17
3.3 Performance	17
3.4 Reliability	17
3.5 Unformatted and formatted capacities	18
3.6 Programmable drive capacity	18
3.7 Factory installed accessories	18
3.8 Options (factory installed)	18
3.9 Accessories (user installed)	18
4.0 Performance characteristics	19
4.1 Internal drive characteristics (transparent to user)	19
4.2 SCSI performance characteristics (visible to user)	19
4.2.1 Access time [5]	19
4.2.2 Format command execution time (minutes) [1]	19
4.2.3 Generalized performance characteristics	19
4.3 Start/stop time	20
4.4 Prefetch/multi-segmented cache control	20
4.5 Cache operation	21
4.5.1 Caching write data	21
4.5.2 Prefetch operation	22
4.5.3 Optimizing cache performance for desktop and server applications	22
5.0 Reliability specifications	23
5.1 Error rates	23
5.1.1 Environmental interference	23
5.1.2 Read errors	23
5.1.3 Write errors	23
5.1.4 Seek errors	23
5.2 Reliability and service	24
5.2.1 Mean time between failure (MTBF)	24
5.2.2 Preventive maintenance	24
5.2.3 Service life	24
5.2.4 Service philosophy	24
5.2.5 Service tools	24
5.2.6 Hot plugging Cheetah 73LP disc drives	25
5.2.7 S.M.A.R.T.	25
5.2.8 Drive Self Test (DST)	26
5.2.8.1 DST Failure Definition	27
5.2.8.2 Implementation	27
5.2.8.2.1 State of the drive prior to testing	27
5.2.8.2.2 Invoking DST	27
5.2.8.2.3 Short and extended tests	28
5.2.8.2.4 Log page entries	28
5.2.8.2.5 Abort	28
5.2.9 Product warranty	29
6.0 Physical/electrical specifications	31
6.1 AC power requirements	31
6.2 DC power requirements	31
6.2.1 Conducted noise immunity	32
6.2.2 Power sequencing	32
6.2.3 12 V - Current profile	32
6.3 Power dissipation	35
6.4 Environmental limits	37
6.4.1 Temperature	37
6.4.2 Relative humidity	37
6.4.3 Effective altitude (sea level)	38
6.4.4 Shock and vibration	38
6.4.4.1 Shock	38
6.4.4.2 Vibration	40
6.4.5 Air cleanliness	40
6.4.6 Acoustics	40
6.4.7 Electromagnetic susceptibility	40
6.5 Mechanical specifications	41
7.0 Defect and error management	43
7.1 Drive internal defects	43
7.2 Drive error recovery procedures	43
7.3 SCSI systems errors	44
8.0 Installation	45
8.1 Drive ID/option select header	45
8.1.1 Notes for Figures 15, 16, and 17.	48
8.1.2 Function description	49
8.2 Drive orientation	50
8.3 Cooling	50
8.4 Drive mounting	51
8.5 Grounding	51
9.0 Interface requirements	53
9.1 General description	53
9.2 SCSI interface messages supported	53
9.3 SCSI interface commands supported	54
9.3.1 Inquiry Vital Product data	57
9.3.2 Mode Sense data	58
9.4 SCSI bus conditions and miscellaneous features supported	61
9.5 Synchronous data transfer	62
9.5.1 Synchronous data transfer periods supported	62
9.5.2 REQ/ACK offset	62
9.6 Physical interface	62
9.6.1 DC cable and connector	62
9.6.2 SCSI interface physical description	64
9.6.3 SCSI interface cable requirements	64
9.6.4 Mating connectors	65
9.6.4.1 Mating connectors for LW model drives	65
9.6.4.2 Mating connectors for LC model drives	65
9.7 Electrical description	73
9.7.1 Multimode—SE and LVD alternatives	73
9.7.1.1 Single-ended drivers/receivers	75
9.7.1.2 Low voltage differential I/O circuits	75
9.7.1.3 General cable characteristics	75
9.8 Terminator requirements	75
9.9 Terminator power	75
9.10 Disc drive SCSI timing	76
9.11 Drive activity LED	77
10.0 Seagate Technology support services	79
Symbols	83
Numerics	83
A	83
B	83
C	83
D	84
E	84
F	84
G	84
H	84
I	85
J	85
L	85
M	85
N	85
O	86
P	86
Q	86
R	86
S	86
T	87
U	87
V	87
W	88

Match case Limit results 1 per page

Cheetah 73LP Product Manual, Rev. C

SCSI interface data transfer rate (asynchronous):

Maximum instantaneous one byte wide

5.0 Mbytes/sec [4]

Maximum instantaneous two bytes wide

10.0 Mbytes/sec [4]

Synchronous formatted transfer rate

Ultra2 SCSI

Ultra3 SCSI

On narrow (8-bit) bus in LVD mode

5.0 to 40 Mbytes/sec

5.0 to 80 Mbytes/sec

On wide (16-bit) bus in LVD mode

5.0 to 80 Mbytes/sec

5.0 to 160 Mbytes/sec

Sector Sizes:

Default

512 byte user data blocks

Variable

512 to 4,096 bytes per sector in even number of bytes per sector.

If n (number of bytes per sector) is odd, then n-1 will be used.

Notes for Section 4.2.

[1]

Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the

request for a Status Byte Transfer to the Initiator (excluding connect/disconnect).

[2]

Typical access times are measured under nominal conditions of temperature, voltage, and horizontal ori-

entation as measured on a representative sample of drives.

[3]

Assumes no errors and no sector has been relocated.

[4]

Assumes system ability to support the rates listed and no cable loss.

[5]

Access time = controller overhead + average seek time.

Access to data = controller overhead + average seek time + latency time.

4.3

Start/stop time

After DC power at nominal voltage has been applied, the drive becomes ready within 20 seconds if the Motor

Start Option is disabled (i.e. the motor starts as soon as the power has been applied). If a recoverable error

condition is detected during the start sequence, the drive executes a recovery procedure which may cause the

time to become ready to exceed 20 seconds. During spin up to ready time the drive responds to some com-

mands over the SCSI interface in less than 3 seconds after application of power. Stop time is less than 30 sec-

onds from removal of DC power.

If the Motor Start Option is enabled, the internal controller accepts the commands listed in the

SCSI Interface

Product Manual

less than 3 seconds after DC power has been applied. After the Motor Start Command has

been received the drive becomes ready for normal operations within 20 seconds typically (excluding an error

recovery procedure). The Motor Start Command can also be used to command the drive to stop the spindle

(see

SCSI Interface Product Manual

, part number 75789509).

There is no power control switch on the drive.

4.4

Prefetch/multi-segmented cache control

The drive provides prefetch (read look-ahead) and multi-segmented cache control algorithms that in many

cases can enhance system performance. “Cache” as used herein refers to the drive buffer storage space when

it is used in cache operations. To select prefetch and cache features the host sends the Mode Select command

with the proper values in the applicable bytes in Mode Page 08h (see the

SCSI Interface Product Manual

Prefetch and cache operation are independent features from the standpoint that each is enabled and disabled

independently via the Mode Select command. However, in actual operation the prefetch feature overlaps cache

operation somewhat as is noted in Section 4.5.1 and 4.5.2.

All default cache and prefetch Mode parameter values (Mode Page 08h) for standard OEM versions of this

drive family are given in Tables 7.

Read/write consecutive sectors on a track

Yes

Flaw reallocation performance impact (for flaws reallocated at format time using

the spare sectors per sparing zone reallocation scheme.)

Negligible

Average rotational latency

2.99 msec