Sennheiser HE 1 Instruction manual HE 1 - Page 50

If a problem occurs

Get Sennheiser HE 1 PDF manuals and user guides View all Sennheiser HE 1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

If a problem occurs ... If a problem occurs ... Problem Possible cause Corrective action Page The headphones cannot be switched on No audio signal No connection to the power supply system. The power fuse has blown. The HE 1 is switched off. Check if the HE 1 is connected to the 26 power supply system and if the power switch is set to ON. Contact your Sennheiser partner. - Switch the HE 1 on. 27 The volume is adjusted to low. Increase the volume. 37 The mute function (MUTE) is Deactivate the mute function. 38 activated. The INPUT rotary switch is set to a Set the INPUT rotary switch to the 32 different audio source. desired audio source. No audio signal when a digital The data format of the digital Set the audio source to PCM data 16 audio source is connected audio source is not PCM. format. The audio signal is very low or The volume of the audio signal on If possible, adjust the volume of the - distorted when an analog audio the audio source is adjusted too audio signal on the audio source to a source is connected low or too high. medium level. The signal level of the INPUT audio input is adjusted too low/ too high. Increase or reduce the signal level of the 33 INPUT audio input. Cracking noise occurs when the This is no malfunction - the Pressure compensation is performed - headphones are put on cracking noise occurs due to a automatically within approx. 2 seconds. temporary overpressure in the ear The headphones are then fully cups. operational. Audio signal only on one ear The analog audio cable is not properly connected. Properly connect the audio cable to the 15 playback device. One tube is defective. Replace the tubes or contact your 42 Sennheiser partner. The PC does not recognize the No driver is installed. HE 1 as the audio output device Install the USB Audio driver. 20 No audio signal when the HE 1 Another audio output device is is connected to a PC via USB selected. Select "Sennheiser HE 1" as the audio 18 output device. No driver is installed. Install the USB Audio driver. 20 Sound dropouts when connected via USB The USB cable is not sufficiently Use a USB cable that is at least USB 2.0 16 shielded. certified. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
48
If a problem occurs ...
If a problem occurs °°°
Problem
Possible cause
Corrective action
Page
The headphones cannot be
switched on
No connection to the power
supply system.
Check if the HE 1 is connected to the
power supply system and if the power
switch is set to ON.
26
The power fuse has blown.
Contact your Sennheiser partner.
–
No audio signal
The HE 1 is switched off.
Switch the HE 1 on.
27
The volume is adjusted to low.
Increase the volume.
37
The mute function (MUTE) is
activated.
Deactivate the mute function.
38
The INPUT rotary switch is set to a
different audio source.
Set the INPUT rotary switch to the
desired audio source.
32
No audio signal when a digital
audio source is connected
The data format of the digital
audio source is not PCM.
Set the audio source to PCM data
format.
16
The audio signal is very low or
distorted when an analog audio
source is connected
The volume of the audio signal on
the audio source is adjusted too
low or too high.
If possible, adjust the volume of the
audio signal on the audio source to a
medium level.
–
The signal level of the INPUT
audio input is adjusted too low/
too high.
Increase or reduce the signal level of the
INPUT audio input.
33
Cracking noise occurs when the
headphones are put on
This is no malfunction – the
cracking noise occurs due to a
temporary overpressure in the ear
cups.
Pressure compensation is performed
automatically within approx. 2 seconds.
The headphones are then fully
operational.
–
Audio signal only on one ear
The analog audio cable is not
properly connected.
Properly connect the audio cable to the
playback device.
15
One tube is defective.
Replace the tubes or contact your
Sennheiser partner.
42
The PC does not recognize the
HE 1 as the audio output device
No driver is installed.
Install the USB Audio driver.
20
No audio signal when the HE 1
is connected to a PC via USB
Another audio output device is
selected.
Select “Sennheiser HE 1” as the audio
output device.
18
No driver is installed.
Install the USB Audio driver.
20
Sound dropouts when con-
nected via USB
The USB cable is not sufficiently
shielded.
Use a USB cable that is at least USB 2.0
certified.
16