Sharp LC-80LE632U LC-80LE632U Operation Manual - Page 10

Quick Reference - tv

Get Sharp LC-80LE632U PDF manuals and user guides View all Sharp LC-80LE632U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

QUICK REFERENCE Attaching the Stand • Before attaching (or detaching) the stand, unplug the AC cord. • Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION • Attach the stand in the correct direction. • Do not remove the stand from the TV unless using a wall mount bracket to mount it. • Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over. • After attaching the stand to the TV, do not hold the stand when you put up, set up, move or lay down the TV. Before attaching the stand to the TV, build a work table on which to rest the TV. • To build the table, use the cushioning materials used in the packaging. TOP-L TOP-R 4 The case is equipped with push-in tabs to hold the cushioning materials in place. Push in the tabs (2 for each location) to secure the cushioning materials in the case. Push-in tabs TOP-C FRONT • Of the cushioning materials used, TOP-C is also used during stand unit assembly. Be sure to assemble the stand unit before building the work table. ■ Stand Unit Assembly 1 Confirm that there are 12 screws (8 long screws and 4 short screws) supplied with the stand unit. 5 After you have built the work table, spread a blanket or similar soft cloth over the table and then lay the TV display down on the covered table. • Do not use a small table for this. 2 1 Set the post for the stand unit onto the TOP-C. 2 Attach the base to the post. 3 Insert and tighten the 8 screws into the 8 holes on the bottom of the base. • Hold the stand unit securely with one hand, and then tighten the screws. 2 ɹɹ 1 2 1 1 Long screws FRONT ■ Building the Work Table 3 Insert each of the cushioning materials in the respective directions shown in the figure. • Insert TOP-L and TOP-R into the left and right sides of the case respectively. • Insert TOP-C to fit between the lines on the other side of the case. TOP-R TOP-L CASE LINE ■ Attaching the Stand to the TV 6 Insert the stand into the openings on the bottom of the TV. • Make sure that the stand is firmly inserted into the TV. Improper installation may result in tilting of the TV set. 7 Insert and tighten the 4 screws into the 4 holes on the rear of the TV. Short screws ɹɹɹ • To detach the stand, perform the steps in reverse order. • In the installation procedure, be careful not to catch your fingers between the TV set and the floor. TOP-C 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
8
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
•
Attach the stand in the correct direction.
•
Do not remove the stand from the TV unless using a wall mount bracket to mount it.
•
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
•
After attaching the stand to the TV, do not hold the stand when you put up, set up, move or lay down the TV.
Before attaching the stand to the TV, build a work
table on which to rest the TV.
• To build the table, use the cushioning materials used in the
packaging.
FRONT
TOP-L
TOP-R
TOP-C
• Of the cushioning materials used, TOP-C is also used
during stand unit assembly. Be sure to assemble the stand
unit before building the work table.
■
Stand Unit Assembly
1
Confirm that there are 12 screws (8 long screws
and 4 short screws) supplied with the stand unit.
2
1
Set the post for the stand unit onto the TOP-C.
2
Attach the base to the post.
3
Insert and tighten the 8 screws into the 8 holes
on the bottom of the base.
•
Hold the stand unit securely with one hand, and then
tighten the screws.
FRONT
2
1
1
1
2
Long
screws
■
Building the Work Table
3
Insert each of the cushioning materials in the
respective directions shown in the figure.
• Insert TOP-L and TOP-R into the left and right sides of
the case respectively.
• Insert TOP-C to fit between the lines on the other side
of the case.
TOP-L
CASE
LINE
TOP-R
TOP-C
4
The case is equipped with push-in tabs to hold
the cushioning materials in place. Push in the
tabs (2 for each location) to secure the cushioning
materials in the case.
Push-in tabs
5
After you have built the work table, spread a
blanket or similar soft cloth over the table and then
lay the TV display down on the covered table.
• Do not use a small table for this.
■
Attaching the Stand to the TV
6
Insert the stand into the openings on the bottom of
the TV.
• Make sure that the stand is firmly inserted into the TV.
Improper installation may result in tilting of the TV set.
7
Insert and tighten the 4 screws into the 4 holes on
the rear of the TV.
Short
screws
• To detach the stand, perform the steps in reverse order.
• In the installation procedure, be careful not to catch your
fingers between the TV set and the floor.