Sharp XE-A202 Quick Installation Guide
Sharp XE-A202 - Electronic Cash Register Manual
 |
UPC - 074000048270
View all Sharp XE-A202 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp XE-A202 manual content summary:
- Sharp XE-A202 | Quick Installation Guide - Page 1
Model XE-A202 For quick set-up, follow the instructions shown below. Note that malfunction may occur if you do not follow the steps. For further information, please read the instruction manual. Before setting up your cash register, prepare three new R6 or LR6 batteries ("AA" size), which are - Sharp XE-A202 | Quick Installation Guide - Page 2
of the paper along with the paper positioning guides as per the diagram. • While holding down the center of the wing part of the arm as per problem occurs, open the arm, and close the arm as instructed above. 2. 3. 5. Journal • Insert the end of the paper into the slit of the spool. (Press the key - Sharp XE-A202 | Quick Installation Guide - Page 3
on the display. 7 Programming A Preset Price • Insert the manager (MA) key into the Mode Lock and turn to the PGM position Procedure To program zero Unit price (max. six digits) DEPTSHIFT* Dept. key TL/NS *To program departments 17 through 32, press the department shift key. REG OPX/Z MGR - Sharp XE-A202 | Quick Installation Guide - Page 4
Mode Lock 10 Reporting The cash register has two reporting types. registers memory. The reports can be taken in the X1/Z1 mode for daily sales or X2/Z2 for periodic (monthly) reports. For further information please refer to the instruction manual. Example Daily Reports • Insert the manager (MA) key
-
1 -
2 -
3 -
4
 |
 |
Model XE-A202
Installing The Cash Register
Install the cash register using the fixing
angle bracket provided with the register.
•
Thoroughly clean the location where the
fixing angle bracket (B) is to be placed.
•
Peel off the adhesive tape on the fixing
angle bracket.
•
Hook the angle bracket onto the hook
(A) that is located at the bottom rear of
the register.
•
Firmly stick the fixing angle bracket to
the table surface that you cleaned above.
To remove the register from the fixing
angle bracket.
•
Lift up the front of the register and pull
the register towards you.
Important Notice
The cash register will
operate correctly only
after the following steps
have been carried out:
1
For quick set-up, follow the instructions shown below. Note that malfunction may occur if
you do not follow the steps. For further information, please read the instruction manual.
Before setting up your cash register, prepare three new R6 or LR6 batteries ("AA" size),
which are necessary for memory backup, and find a stable surface near an AC outlet
where the cash register is not subject to water sources or direct sunlight.
PGM
MGR
OPX/Z
REG
X2/Z2
X1/Z1
Mode Lock
PGM
MGR
OPX/Z
REG
X2/Z2
X1/Z1
Mode Lock
Preparing The Cash Register
Initialising The Cash Register
To ensure the cash register operates correctly, initialize it using the following
procedure.
•
Make sure the AC power cord is unplugged and batteries are not installed
in the register.
•
Insert the manager (MA) key into the mode switch and turn to the
REG
position.
•
Insert the plug of the AC power cord into the AC outlet. A buzzer will sound 3 times.
IMPORTANT: This operation must be performed without batteries installed.
•
The register display should now show "
0.00".
NOTE:
If the buzzer does not sound when the plug is inserted, the
initialization has not been done successfully. Wait at least one minute
after pulling out the plug, and insert the plug again.
Installing the Batteries
Install three new R6 or LR6 batteries ("AA" size) according to the procedure
shown below with the power cord connected and set the mode switch to
REG
position.
•
Lift the rear of the printer cover and detach it.
•
Open the battery compartment cover.
•
Install three new R6 or LR6 batteries ("AA"size) as per the diagram.
When the batteries are properly installed "
" on the display will disappear.
•
Close the battery compartment cover.
2