Sharp XR-10XDM XG-MB55X Operation Manual - Page 64

Troubleshooting Continued

Get Sharp XR-10XDM PDF manuals and user guides View all Sharp XR-10XDM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Troubleshooting (Continued) Problem Check Picture is green on • Change the input signal type setting. INPUT 1 (COMPONENT)/ • When you cannot select an input signal type, select "Color is faded INPUT 2 (COMPONENT). or poor" in the "Help" menu, after selecting an item other than Picture is pink (no green) "sRGB" in "Picture Mode", and then select an input signal type. on INPUT 1 (RGB)/INPUT 2 (RGB). Picture is too bright and • Image adjustments are incorrectly set. whitish. The cooling fan becomes • When temperature inside the projector increases, the cooling fan noisy. runs faster. The lamp does not light • The lamp indicator is illuminating in red. up even after the Replace the lamp. projector turns on. The lamp suddenly turns off during projection. The image sometimes flickers. • Cables incorrectly connected to the projector or the connected equipment works improperly. • Select "Vertical stripes or flickering image appear" in the "Help" menu and make the necessary adjustments. • If this happens frequently, replace the lamp. The lamp needs much • The lamp will eventually need to be changed. time to turn on. While the remaining lamp life draws to a close, replace the lamp. Picture is dark. Page 46 39, 46 40 - 48, 51 23-26 46 51 51 This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
60
Problem
Picture is green on
INPUT 1 (COMPONENT)/
INPUT 2 (COMPONENT).
Picture is pink (no green)
on INPUT 1 (RGB)/INPUT
2 (RGB).
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.
Check
•
Change the input signal type setting.
•
When you cannot select an input signal type, select “Color is faded
or poor” in the “Help” menu, after selecting an item other than
“sRGB” in “Picture Mode”, and then select an input signal type.
•
Image adjustments are incorrectly set.
•
When temperature inside the projector increases, the cooling fan
runs faster.
•
The lamp indicator is illuminating in red.
Replace the lamp.
•
Cables incorrectly connected to the projector or the connected
equipment works improperly.
•
Select “Vertical stripes or flickering image appear” in the “Help”
menu and make the necessary adjustments.
•
If this happens frequently, replace the lamp.
•
The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
Page
46
39, 46
40
–
48, 51
23–26
46
51
51
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
Troubleshooting (Continued)