Singer 1 One Instruction Manual 9

Singer 1 One Manual

Get Singer 1 One PDF manuals and user guides View all Singer 1 One manuals
Add to My Manuals
Save this manual to your list of manuals

Singer 1 One manual content summary:

  • Singer 1 One | Instruction Manual 9 - Page 1
    * 127-3 & 128-3 with VIBRATING SHUTTLE Copyright, U. S. A., 1915, 1923, 1929, 1932, 1935 and 1940, by The Singer Manufacturing Company All Rights Reserved for all Countries *A Trade Mark of THE SINGER MANUFACTURING CO. INSTRUCTION MANUAL Table of Contents | Next Page
  • Singer 1 One | Instruction Manual 9 - Page 2
    Bobbin Thread Skipping of Stitches Instructions for Using the Attachments Foot Hemmer -- Hemming -- Hemming and Sewing on Lace -- Felling Machine To Adjust the Ruffler for Gathering To Make a Ruffle and Sew it to a Gament in One Operation Piping a Ruffle To Adjust the Ruffler for Plaiting To Adjust
  • Singer 1 One | Instruction Manual 9 - Page 3
    Main Parts 127-3 & 128-3 TO ALL WHOM IT MAY CONCERN: The improper placing or renewal of the TradeMark "SINGER" or any other of the Trade Marks of The Singer Manufacturing Company (all of which are duly Registered Trade Marks) on any machine that has been repaired, rebuilt, reconditioned, or
  • Singer 1 One | Instruction Manual 9 - Page 4
    127-3 & 128-3 Instructions for Operating the Machines Raise the you. This will start the band wheel, treadle and pitman, the sewing mechanism having been disconnected. Continue the motion thus begun by an alternate pressure guiding the material. Table of Contents Previous Page | Next Page 4
  • Singer 1 One | Instruction Manual 9 - Page 5
    127-3 & 128-3 To Ensure Perfect Action of the Machine To Remove the Shuttle The balance wheel must always turn over toward the operator. Do not run the machine with the presser foot resting on the feed without cloth under the presser foot. Do not run the machine when both shuttle and needle are
  • Singer 1 One | Instruction Manual 9 - Page 6
    6) against the hub of the balance wheel, and turn the balance wheel until the thread guide (4, Fig. 6) moves to the extreme right. Put the spool of thread on the Fig. 6) at the right. Then operate the machine the same as for sewing. When the bobbin is filled, remove it from the bobbin winder, pull
  • Singer 1 One | Instruction Manual 9 - Page 7
    127-3 & 128-3 To Thread the Shuttle Hold the shuttle between the thumb and fingers of the left hand as shown in Fig. 7. Place the bobbin into the shuttle with the thread drawing toward the right from the side of the bobbin nearest you, as shown in Fig. 7. Place the forefinger of the left hand on the
  • Singer 1 One | Instruction Manual 9 - Page 8
    127-3 & 128-3 To Replace the Shuttle After threading, take the shuttle in the right hand with the point toward you and the tension adjusting screw (1, Fig. 7, page 8) upwards. Put the point of the shuttle into the front end of the shuttle carrier as shown in Fig. 10, and drop the shuttle into place,
  • Singer 1 One | Instruction Manual 9 - Page 9
    the spool pin at the top of the machine, lead the thread into the thread guide (1) at the top of the face plate, down under and from right to left down into the eyelet (5) in front of the face plate, into the lower wire guide (6) then from left to right through the eye of the needle (7). Draw about
  • Singer 1 One | Instruction Manual 9 - Page 10
    both threads back under the presser foot and close the slides. Place the material beneath the presser foot, lower the presser foot and commence to sew, turning the balance wheel over toward you. Remove the Work Let the thread take-up lever rest at its highest point, raise the presser foot
  • Singer 1 One | Instruction Manual 9 - Page 11
    127-3 & 128-3 Tensions To Regulate the Tensions For ordinary stitching the needle and the bobbin threads should be locked in the centre of the thickness of the material, thus: FIG. 13. PERFECT STITCH The tension on the needle thread should only be regulated when the presser foot is down. Having
  • Singer 1 One | Instruction Manual 9 - Page 12
    -3 & 128-3 To Turn a Corner To Sew Flannel or Bias Seams Stop the machine with 15. To Regulate the Pressure on the Material For ordinary family sewing it is seldom necessary to change the pressure on the material. If sewing fine silk or flimsy material, lighten the pressure by turning the thumb
  • Singer 1 One | Instruction Manual 9 - Page 13
    be tight enough not to slip. If too loose remove the hook at one end, shorten the belt and rejoin. Machine Working Heavily. If the machine the presser foot or attachments are securely fastened by the thumb screw, Do not sew heavy seams or very thick goods with too fine a needle. A large needle and
  • Singer 1 One | Instruction Manual 9 - Page 14
    . With moderate use all occasional oiling is sufficient. Oil should he applied at each of the places shown by arrows in Figs. 16 and 17. One drop of oil at each point is sufficient. Oil holes are provided in the machine for bearings which cannot be directly reached. To oil the
  • Singer 1 One | Instruction Manual 9 - Page 15
    127-3 & 128-3 To Oil the Machine continued... On the back of the arm is a round plate or cover, fastened by a thumb screw. Loosen the screw, turn the plate upward and fasten by tightening the screw; turn the balance wheel slowly and oil the moving parts inside, then turn the cover down and fasten
  • Singer 1 One | Instruction Manual 9 - Page 16
    128-3 INSTRUCTIONS FOR through the hemmer together and hemming them down. FOOT HEMMER Hemming and Sewing on Lace Start the hem as previously explained, and when it is the lace and hem together. Then let down the presser bar and guide tile lace over the front of the hemmer, keeping it well into
  • Singer 1 One | Instruction Manual 9 - Page 17
    Felling The two pieces of cloth to be felled should be laid one over the other, right sides together, the edge of the under piece left hand draw the edges into the hemmer which will turn them as in hemming. Guide the second row of stitching by following the first row with the inside of the
  • Singer 1 One | Instruction Manual 9 - Page 18
    cloth back and forth until the hem is formed, stopping with the end under the needle. Lower the presser bar and commence to sew, being careful to so guide cloth as to keep hemmer full. To make a hem more than 15/16 inch wide, loosen the thumb screw in the hemmer and
  • Singer 1 One | Instruction Manual 9 - Page 19
    the edge of the goods to be bound between the scrolls of the binder and draw it under the needle. Lower the presser bar and sew as usual. To make French folds proceed as directed for binding except that the fold is stitched on to the face of the material instead
  • Singer 1 One | Instruction Manual 9 - Page 20
    line on the presser foot will be the same as that at which the guide is located on the scale nearest the needle. To make spaces between the tuck underneath and against the spur at the left. The spur will serve as a guide and will also make a distinct crease for the next tuck. Always place the last
  • Singer 1 One | Instruction Manual 9 - Page 21
    127-3 & 128-3 The names and uses of the principal parts of the ruffler are as fol- lows: (SEE: REFERENCES IN Fig. 26) A -- FOOT -- the part by which the ruffler is attached to the presser bar. B -- FORK ARM-- the section that must be placed astride the needle clamp. C -- ADJUSTING SCREW -- the
  • Singer 1 One | Instruction Manual 9 - Page 22
    the two blue blades, following the line 2 in Fig. 26. Draw the material slightly back of the needle, lower the presser bar and commence to sew. To make fine gathering, shorten the stroke of the ruffling blade by turning the adjusting screw (C, Fig. 27) upwardly, also shorten the stitch. To make
  • Singer 1 One | Instruction Manual 9 - Page 23
    127-3 & 128-3 To Make a Ruffle and Sew it to a Garment in One Operation To Ruffle and Sew on a Facing in One Operation Insert the material to be ruffled between the two blue blades, as shown in Fig. 28, following the line 2, in Fig. 26. Place the
  • Singer 1 One | Instruction Manual 9 - Page 24
    127-3 & 128-3 Piping a Ruffle To Adjust the Ruffler for Plaiting Insert the material to be ruffled between the two blue blades, following the line 2, in Fig. 26. This material must not be over 1 1/4 inches wide, as it is carried through the ruffler with the finished edge of the ruffle to the
  • Singer 1 One | Instruction Manual 9 - Page 25
    of material to prevent the oil soiling the work. If the ruffler does not plait evenly, a drop of oil may remedy the trouble. SINGER Needles should be used in SINGER Machines. These Needles and their Containers are marked with the Company's Trade Mark "SIMANCO"* Needles in Containers marked "FOR
  • Singer 1 One | Instruction Manual 9 - Page 26
    127-3 & 128-3 SIZES OF NEEDLES 9 11 14 16 18 19 RELATIVE SIZES OF NEEDLES AND THREAD (Class and Variety of Needles Used, 15x1) CLASSES OF WORK Georgette, chiffon, net, light weight synthetic, fabrics, fine dimity, lawn, batiste, and other featherweight or sheer fabrics. For infants' clothes and
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
127-3 & 128-3
Table of Contents
| Next Page
INSTRUCTION MANUAL
with VIBRATING SHUTTLE
Copyright, U. S. A., 1915, 1923, 1929, 1932, 1935
and 1940, by The Singer Manufacturing Company
All Rights Reserved for all Countries
*
A Trade Mark of
THE SINGER MANUFACTURING CO.
*