Sony CPF-NW001P Quick Setup Guide
Sony CPF-NW001P - Main Component Of Cpf-ix001 Wireless Network Audio System Manual
 |
View all Sony CPF-NW001P manuals
Add to My Manuals
Save this manual to your list of manuals |
Sony CPF-NW001P manual content summary:
- Sony CPF-NW001P | Quick Setup Guide - Page 1
unit (NAS-IX001P) Subwoofer (SA-NW001P) Network cable for the CPF-IX001 Remote commander (RM-ANU007) M-crew Server Ver. 2.0 software CD-ROM 2 Insert the supplied M-crew Server Ver. 2.0 software CD-ROM into your computer. The "M-crew Server SETUP" window appears. Follow the instructions on - Sony CPF-NW001P | Quick Setup Guide - Page 2
version. For details, refer to the operation manual of your wireless LAN router. 2 Press Troubleshooting Step 1-2 2-4 3-1, 3-8 3-3 3-11 Symptom Action The firewall settings screen appear. Follow the instructions one by one. 1 Confirm the security software (Firewall) setting on your computer. 2
-
1 -
2
 |
 |
CPF-IX001
Quick Setup Guide
2-892-537-
12
(2)
© 2006 Sony Corporation
Printed in Malaysia
Step 1
This Quick Setup Guide explains the preparation needed to enjoy
music with the CPF-IX001.
For details on each step, refer to the Operating instructions in the
supplied CD-ROM.
CPF-IX001 Operating Instructions
for details on how to operate the CPF-IX001
M-crew Server Installation instructions
for details on how to install the M-crew Server
M-crew Server Help
(Use aſter installing the M-crew)
for details on how to operate the M-crew Server
Check the following website for the CPF-IX001 latest
information, FAQ (Frequently Asked Questions), and
firmware updates;
USA:
Canada:
shtml
Europe:
Notes
When using the CPF-IX001 with a wireless network, you need a wireless LAN router
(access point, not supplied)
A wireless connection (ad-hoc) cannot be made directly with a computer.
Setup Procedure
Wireless settings for the CPF-IX001 must be made from
a computer that has a wired connection with the CPF-
IX001. Be sure to perform the settings by following the
procedure below.
Step 1
Installing M-crew Server
Step 2
Setting a wired connection
Step 3
Setting a wireless connection
Step 2
°e CPF-IX001 wireless settings are made using the
browser, so first establish a wired connection between
the CPF-IX001 and your computer.
1
Connect the CPF-IX001 to the network
using a wired connection.
Connect the CPF-IX001 to your router (hub) or directly to the
LAN port of the computer. Use the supplied network cable.
Check that the WIRELESS/WIRED selector on the network unit
is set to WIRED.
Network cable (supplied)
To router (hub) or
LAN port of the
computer
To LAN port
WIRELESS/WIRED selector
Note
When using the CPF-IX001 with a fixed IP address, refer to “Advanced
network settings” in the Operating Instructions.
2
Turn on the system.
Power switch
Note
°e demonstration display appears on the network unit. If it does not
appear, check the connection (Step 1-4).
3
Press FUNCTION repeatedly until the
LINE indicator on the main unit turns
off.
SUSPEND
FUNCTION
4
Press SUSPEND to start up the network
unit.
°e model name appears in the display and the connection
starts. “Configuring” flashes and the network is configured.
Note
When connected one-to-one with a computer without using a router, it
takes a few minutes to configure the network. In addition, a warning mes-
sage appears on the computer to advise that the connection is restricted.
5
Press
and check that music or
sample music is played.
It may take some time until music playback starts depending
on the network status. During the sample music playback, the
following appears in the display.
Note
If “SERVER?” appears, select the M-crew server according to the following
procedure.
1
Press ENTER.
2
Press
or
repeatedly until “M-crew v2 on XXXX (your com-
puter name)” appears, then press ENTER.
°is completes the settings when using the CPF-IX001 with a
wired connection.
When using the CPF-IX001 with a wireless connection, press
to stop music playback, then proceed to Step 3.
Continued
3
Prepare the remote.
Pull out the insulating sheet.
4
Install the CPF-IX001.
Connect the network unit on the main unit, and connect the
subwoofer to the DC IN jack on the back of the main unit.
To DC IN jack
To the wall outlet
Network unit
Main unit
Subwoofer
Note
Be sure to turn off the subwoofer when connecting or disconnecting the
network unit.
Install the M-crew Server Ver. 2.0 soſtware and prepare
the CPF-IX001.
1
Make sure that you have all the
following items, which are required for
setup.
Main unit (CPF-NW001P)
Network unit (NAS-IX001P)
Subwoofer (SA-NW001P)
Network cable for the CPF-IX001
Remote commander (RM-ANU007)
M-crew Server Ver. 2.0 soſtware CD-ROM
2
Insert the supplied M-crew Server
Ver. 2.0 software CD-ROM into your
computer.
°e “M-crew Server SETUP” window appears. Follow the
instructions on the screen and install the soſtware.
Select language
Click to install
Notes
If the window does not open, double-click the CD-ROM “Setup.exe”
icon.
With some computer environments, you may need to set the Windows
and security soſtware firewall.
If the “Windows Security Alert” window appears, click [Unblock] to
unblock the program.
If the “ICF SETTINGS” window automatically appears, click [Apply], and
“OK” appears for all status items, then click [Close].