Sony DCR-SR68 Handycam® Handbook - Page 13

DCR-SR68/SR88, DCR-SX43/SX44/SX63, To remove the battery pack - camcorder battery

Get Sony DCR-SR68 - Hard Disk Drive Handycam Camcorder PDF manuals and user guides
UPC - 027242788701
View all Sony DCR-SR68 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Getting started To remove the battery pack Close the LCD screen. Slide the BATT (battery) release lever () and remove the battery pack (). DCR-SR68/SR88 DCR-SX43/SX44/SX63 To use a wall outlet (wall socket) as a power source Make the same connections as "Step 1: Charging the battery pack." Even if the battery pack is attached, the battery pack is not discharged. Charging the battery pack abroad You can charge the battery pack in any countries/regions using the AC Adaptor supplied with your camcorder within the AC 100 V - 240 V, 50 Hz/60 Hz range.  Notes  Do not use an electronic voltage transformer. Notes on the battery pack  When you remove the battery pack or disconnect the AC Adaptor, close the LCD screen and make sure that the (Movie)/ (Photo) lamps (p. 15), the access lamp (p. 19) are turned off.  The CHG (charge) lamp flashes during charging under the following conditions:  The battery pack is not attached correctly.  The battery pack is damaged.  The temperature of the battery pack is low. Remove the battery pack from your camcorder and put it in a warm place.  The temperature of the battery pack is high. Remove the battery pack from your camcorder and put it in a cool place.  In the default setting, the power turns off automatically if you leave your camcorder without any operation for about 5 minutes, to save battery power ([A.SHUT OFF], p. 70). US 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
13
Getting started
US
To remove the battery pack
Close the LCD screen. Slide the BATT (battery) release lever (
) and remove the battery
pack (
).
DCR-SR68/SR88
DCR-SX43/SX44/SX63
To use a wall outlet (wall socket) as a power source
Make the same connections as “Step 1: Charging the battery pack.” Even if the battery pack is
attached, the battery pack is not discharged.
Charging the battery pack abroad
You can charge the battery pack in any countries/regions using the AC Adaptor supplied with
your camcorder within the AC 100 V - 240 V, 50 Hz/60 Hz range.
Notes
Do not use an electronic voltage transformer.
Notes on the battery pack
When you remove the battery pack or disconnect the AC Adaptor, close the LCD screen and make sure
that the
(Movie)/
(Photo) lamps (p. 15), the access lamp (p. 19) are turned off.
The CHG (charge) lamp flashes during charging under the following conditions:
The battery pack is not attached correctly.
The battery pack is damaged.
The temperature of the battery pack is low.
Remove the battery pack from your camcorder and put it in a warm place.
The temperature of the battery pack is high.
Remove the battery pack from your camcorder and put it in a cool place.
In the default setting, the power turns off automatically if you leave your camcorder without any
operation for about 5 minutes, to save battery power ([A.SHUT OFF], p. 70).