Sony PCV-R526DS Reference Manual - Page 51

Installing a 3º” Internal Hard Disk Drive, holder to the top of the chassis.

Get Sony PCV-R526DS - Vaio Digital Studio Desktop Computer PDF manuals and user guides View all Sony PCV-R526DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Removing, Installing, and Replacing Components 43 Installing a 3½" Internal Hard Disk Drive Your system comes with an available bay to hold an additional 3½" hard disk drive. The drive you install must not require front panel access. The hard disk drive access light blinks when either internal drive is active. ! Before opening the system unit, save any open files, exit Windows, turn off the power of the computer and all attached peripherals, and then unplug the power cord. 1 Configure the jumpers on the new drive as a primary slave (see your drive's documentation for configuration instructions). Power connector Jumpers Drive connector KY0084.VSD 2 Disconnect the power cord from the computer. 3 Remove the cover (see "Removing the Cover" on page 24). 4 Remove the four screws (A in next diagram) that secure the drive holder to the top of the chassis.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Removing, Installing, and Replacing Components
43
Installing a 3½” Internal Hard Disk Drive
Your system comes with an available bay to hold an additional 3½” hard
disk drive. The drive you install must not require front panel access. The
hard disk drive access light blinks when either internal drive is active.
1
Configure the jumpers on the new drive as a primary slave (see your
drive’s documentation for configuration instructions).
2
Disconnect the power cord from the computer.
3
Remove the cover (see
“Removing the Cover”
on page 24).
4
Remove the four screws (A in next diagram) that secure the drive
holder to the top of the chassis.
!
Before opening the system unit, save any open files, exit Windows, turn off
the power of the computer and all attached peripherals, and then unplug the
power cord.
KY0084.VSD
Drive connector
Power connector
Jumpers