Sony SLV-N50 Operating Instructions - Page 9

Completing A/V hookup, Getting Started - operating instructions

Get Sony SLV-N50 - Video Cassette Recorder PDF manuals and user guides View all Sony SLV-N50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Getting Started Completing A/V hookup: After you've connected your TV and completed antenna or cable hookup, return to this procedure to complete VCR set up. This will prevent unwanted noise in the RF channel. Press MENU and select ADVANCED OPTIONS. TIMER SET/CHECK SETTINGS ADVANCED OPTIONS SELECT : SET : OK QUIT : MENU , Set AUTO ANT SELECT to OFF and press OK. ADVANCED OPTIONS AUTO ANT SELECT AUTO STEREO TUNER AUDIO APC TAPE SELECT AUTO TAPE SPEED FAVORITE CH SHARPNESS RETURN SELECT : SET : OK QUIT : MENU ON OFF ON AUTO ON ON L H For details, see page 68. Caution Connections between the VCR's VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to an antenna or make simultaneous (parallel) antenna and VCR connections at the antenna terminals of your receiver. Note to CATV system installer (in USA) This reminder is provided to call the CATV system installer's attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Hookups 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Getting Started
9
Hookups
Completing A/V hookup:
After you’ve connected your TV and completed antenna or cable hookup, return to
this procedure to complete VCR set up. This will prevent unwanted noise in the RF
channel.
Caution
Connections between the VCR’s VHF/UHF connector and the antenna terminals of the TV
receiver should be made only as shown in the following instructions.
Failure to do so may result
in operation that violates the regulations of the Federal Communications Commission regarding
the use and operation of RF devices.
Never connect the output of the VCR to an antenna or
make simultaneous (parallel) antenna and VCR connections at the antenna terminals of your
receiver.
Note to CATV system installer (in USA)
This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable
entry as practical.
SET
:
SELECT
:
OK
MENU
QUIT
:
TIMER SET/CHECK
SETTINGS
ADVANCED OPTIONS
SET
:
SELECT
:
OK
MENU
QUIT
:
ADVANCED OPTIONS
AUTO STEREO
AUTO ANT SELECT
TUNER AUDIO
APC
TAPE SELECT
OFF
ON
ON
AUTO
AUTO TAPE SPEED
ON
ON
SHARPNESS
L
H
RETURN
FAVORITE CH
Press MENU and select
ADVANCED OPTIONS.
Set AUTO ANT SELECT
to OFF and press OK.
For details, see page 68.
,