Sony STR-DA3400ES Quick Setup Guide - Page 2
automatically Auto Calibration
View all Sony STR-DA3400ES manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
AUTO CAL MIC 5 6 8 / , 10 3289139111.indd 2 3 4 5-10, MENU 14-18 13 15 / , 16 / , 18 English Calibrating the appropriate speaker settings automatically (Auto Calibration) You can set up the speakers to obtain the desired sound from all connected speakers automatically by using the Auto Calibration function. Before you perform the Auto Calibration During the calibration, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood. Perform the measurement in a quiet environment to avoid the effect of noise and get a more accurate measurement. If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacle from the measurement area to avoid measurement error. 1 Install and connect the speakers and TV. For detail, see front page. 2 Connect the supplied optimizer microphone to the AUTO CAL MIC jack. The AUTO CAL MIC jack is used for the supplied optimizer microphone only. Do not connect other microphones. Doing so may damage the receiver and the microphone. 3 Set up the optimizer microphone. Place the optimizer microphone at your seating position. Use a stool or tripod so that the optimizer microphone remains at the same height as your ears. On setting up the active subwoofer When a subwoofer is connected, turn on the s�u��b�w�o��o�f�e�r�a�n���d����t��u��r�n� up the volume beforehand. Turn the MASTER VOLUME knob to just before the mid-point. If you connect a subwoofer with the crossover frequency function, set the value to maximum. If you connect a subwoofer with an auto standby function, set it to off (deactivated). Performing Auto Calibration The Auto Calibration function allows you to measure the following: speaker connections, polarity of speakers, speaker distance, speaker size, speaker level, frequency characteristics. 1 Connect a TV to this receiver. Refer to "3: Connecting the TV" in the operating instructions. 2 Turn on the TV. 3 Press ?/1 to turn on the receiver. Switch the input of the TV so that an image of the menu is displayed. 4 Press GUI MODE repeatedly to select "GUI ON". "GUI MODE" appears in the display window of the receiver and the GUI menu appears on the TV screen. Press MENU if the GUI menu does not appear on the TV screen. 5 Press / repeatedly to select "Settings", then press� �o�r�� . The Settings menu list appears on the TV screen. 6 Press / repeatedly to select "Auto Calibration", then press �o�r�� . 7 Press / repeatedly to select "Quick Setup", then press . 8 Press / repeatedly and to un-check the items you do not want to measure. Speaker Distance Speaker Level Frequency Characteristic 9 Press . 10 Press to select "Start". 11 The measurement starts in 5 seconds. 12 Measurement starts. The measurement process will take approximately 30 seconds with a test tone. Wait until the measurement process completes. 13 The measurement is completed. When the measurement ends, a beep sounds and the measurement result appears on the TV screen. 14 Press to select "Next". 15 Press / r�e��p�e�a�t�e��d�l�y�t�o��s�e�l�e�c�t Y�e��s�"�,�t�h�e�n��p��r�e�s�s� . 16 Press / repeatedly to select the Auto Calibration type, then press . Parameter Full Flat Engineer Front Reference OFF Explanation Makes the measurement of frequency from each speaker flat. Sets the frequency to one that matches that of the Sony listening room standard. Adjusts the characteristics of all the speakers to match the characteristics of the front speaker. Sets the Auto Calibration EQ to off. 17 Press . The exit screen appears. 18 Press to exit. When error codes appear For details on warning and error codes, see "Message list after Auto Calibration measurement" in "9: Calibrating the appropriate speaker settings automatically (Auto Calibration)" in the operating instructions. Tip The size of a speaker (LARGE/SMALL) is determined by the low characteristics. The measurement results may vary, depending on the position of the optimizer microphone and speakers, and the shape of the room. It is recommended that you follow the measurement results. However, you can change those settings in the Speaker settings menu. Save the measurement results first, then try to change the settings if you want. Setting up other components You should set up each component so that the sound is output from speakers correctly when you play back a connected component. The following case describes Sony components. Refer to the operating instructions supplied with each component. Sony Super Audio CD player Select a suitable playback area (multi channel or 2 channel). Sound may come out from only the front speaker left/right when 2 channel is selected. After the setting The receiver is now ready to use. Refer to the operating instruction supplied with the receiver for details. Español Calibrando automáticamente los ajustes apropiados del altavoz (Auto Calibration) Puede instalar los altavoces para obtener automáticamente el sonido que desee a través de todos los altavoces conectados mediante la función de calibración automática. Antes de realizar la calibración automática Durante el calibrado, el sonido que proviene de los altavoces es muy fuerte. El volumen del sonido no puede ajustarse. Ponga atención a la presencia de niños o al efecto en su vecindario. Lleve a cabo la medición en un entorno callado para evitar el efecto del ruido y obtenga una medición más precisa. Si hay algún obstáculo en la ruta entre el micrófono optimizador y los altavoces, no se podrá realizar la calibración correctamente. Quite cualquier obstáculo del área de medición para evitar un error de medición. 1 Instale y conecte los altavoces y la TV. Para detalles, ver a la página frontal. 2 Conecte el micrófono optimizador proporcionado a la toma AUTO CAL MIC. La toma AUTO CAL MIC es utilizada solamente para el micrófono optimizador proporcionado. No conecte otros micrófonos. El hacerlo puede dañar el receptor y el micrófono. 3 Configure el micrófono optimizador. Coloque el micrófono optimizador en su posición sentado. Utilice una tarima o trípode de modo que el micrófono optimizador permanezca a la misma altura de sus oídos. Al configurar el altavoz de subgraves activo Cuando se conecta un altavoz de subgraves, encienda el altavoz de subgraves y de antemano suba el volumen. Gire la perilla del MASTER VOLUME a un poco antes del punto medio. Si conecta un altavoz de subgraves con la función de frecuencia de cruce, ajuste el volumen al máximo. Si conecta un altavoz de subgraves con una función automática de modo de espera, apague el altavoz de subgraves (desactivado). Realizando la calibración automática La función de auto calibrado le permite medir lo siguiente: conexiones de altavoz, polaridad de altavoces, distancia de altavoz, tamaño de altavoz, nivel de altavoz, características de frecuencia. 1 Conecte un TV a este receptor. Refiérase a "3: Conectando el televisor" en las manual de instrucciones. 2 Encienda el TV. 3 Presione ?/1 para encender el receptor. Conmute la entrada del TV para que se visualice la imagen del menú. 4 Presione repetidamente GUI MODE para seleccionar "GUI ON". "GUI MODE" aparece en la ventana de la pantalla del receptor y el menú GUI aparece en la pantalla de TV. Presione MENU si el menú GUI no aparece en la pantalla de TV. 5 Presione repetidamente / para seleccionar "Settings", luego presione� o�� . La lista del menú Settings aparece en la pantalla de TV. 6 Presione repetidamente / para seleccionar "Auto Calibration", luego presione �o� . 7 Presione repetidamente / para seleccionar "Quick Setup", luego presione . 8 Presione repetidamente / y para quitar la selección de los puntos que no desea medir. Speaker Distance Speaker Level Frequency Characteristic 9 Presione . 10 Presione para seleccionar "Start". 11 La medición se inicia en cinco segundos. 12 Se inicia la medición. El proceso de medición tomará aproximadamente 30 segundos con un tono de prueba. Espere hasta que se complete el proceso de medición. 13 La medición se completa. Cuando finalice la medición, se oye un pitido y en la pantalla de TV se visualiza el resultado de la medición. 14 Presione para seleccionar "Next". 15 Presione repetidamente / �p�a�r�a��s�e�l�e�c�c�i�o�n�a��r "Yes", luego presione . 16 Presione repetidamente / para seleccionar el tipo de calibración automática, luego presione . Parámetro Full Flat Engineer Front Reference OFF Explicación Realiza la medición de frecuencia de cada base de los altavoces. Establece la frecuencia a una que coincida con la de la norma del cuarto de escucha Sony. Ajusta las características de todos los altavoces para coincidir con las características del altavoz frontal. Establece la calibración automática EQ a apagado. 17 Presione . Aparece la pantalla de salida. 18 Presione para salir. Cuando aparecen códigos de error Para detalles sobre advertencias y códigos de error, ver "Lista de Mensajes después de la Medición de Calibración Automática" en "9: Calibrando automáticamente los ajustes apropiados del altavoz (Auto Calibration)" en las manual de instrucciones. Consejo El tamaño del altavoz (LARGE/SMALL) es determinado por las características bajas. Los resultados de medición pueden variar, dependiendo de la posición del micrófono optimizador y altavoces, y la forma del cuarto. Se recomienda que siga los resultados de medición. Sin embargo, puede cambiar aquellos ajustes en el menú de configuraciones de Speaker. Guarde primeramente los resultados de medición, luego trate de cambiar los ajustes si lo desea. Configuración de otros componentes Es necesario configurar cada componente para que el sonido se emita correctamente a través de los altavoces al reproducir un componente conectado. En el caso siguiente, se describe la configuración de componentes Sony. Consulte el manual de instrucciones suministrado con cada componente en cuestión. Reproductor de Super Audio CD Sony Seleccione un área de reproducción adecuada (multicanal o bien de 2 canales). Es posible que el sonido se emita únicamente a través de los altavoces frontales izquierdo y derecho si se selecciona el ajuste de 2 canales. Tras realizar el ajuste El receptor está listo para utilizarse. Consulte el manual de instrucciones suministrado con el receptor para obtener más información. 4/28/2008 2:35:49 PM