Stihl KM 130 R Product Instruction Manual - Page 13

Mounting the Control Handle, Fitting the Throttle Cable, Throttle Cable Adjustment - engine

Get Stihl KM 130 R PDF manuals and user guides View all Stihl KM 130 R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

English / USA 002BA234 KN 250BA002 KN 14 15 8 15 14 15 : Place the secured assembly on the handle support (8) with the wing screw at the engine side. : Push the wing screw into the handle support as far as stop and then screw it down - but do not finally tighten yet. : Line up the handlebar at a right angle to the drive tube - check dimension A again. : Tighten down the wing screw firmly Mounting the Control Handle : Loosen the screw (9). The nut (10) remains in the control handle (11). : Push the control handle - throttle trigger (12) must point toward the gearbox - onto the handlebar (7) so that the holes (13) line up. : Insert screw and tighten down firmly. Fitting the Throttle Cable Do not kink the throttle cable or lay it in tight radii - make sure the throttle trigger moves freely. : Press the throttle cable (14) into the retainers (15). Throttle Cable Adjustment On control handles with slide: : Go to chapter "Adjusting the Throttle Cable". * see "Guide to Using this Manual" 12 KM 110, KM 130

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
12
English / USA
KM 110, KM 130
:
Place the secured assembly on the
handle support (
8
) with the wing
screw at the engine side.
:
Push the wing screw into the handle
support as far as stop and then
screw it down – but do not finally
tighten yet.
:
Line up the handlebar at a right
angle to the drive tube – check
dimension
A
again.
:
Tighten down the wing screw firmly
Mounting the Control Handle
:
Loosen the screw (
9
). The nut (
10
)
remains in the control handle (
11
).
:
Push the control handle – throttle
trigger (
12
) must point toward the
gearbox – onto the handlebar (
7
) so
that the holes (
13
) line up.
:
Insert screw and tighten down
firmly.
Fitting the Throttle Cable
Do not kink the throttle cable or lay
it in tight radii – make sure the
throttle trigger moves freely.
:
Press the throttle cable (
14
) into the
retainers (
15
).
Throttle Cable Adjustment
On control handles with slide:
:
Go to
chapter "Adjusting the
Throttle Cable".
*
see "Guide to Using this Manual"
002BA234 KN
8
15
14
15
14
15
250BA002 KN