Sunbeam SCH7221 User Manual - Page 1
Sunbeam SCH7221 Manual
View all Sunbeam SCH7221 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
AUTO SAFETY SHUT-OFF AUTO SAFETY SHUT-OFF This heater is equipped with a technologically-advanced safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit. If the heater shuts down and the Power Light Ring is flashing: 1. Stand the heater upright. 2. Unplug the unit and wait 30 minutes. 3. Plug in and operate normally. 4. If the heater does not work normally, repeat steps 1, 2 and 3 again. NOTE: If the heater is plugged in again and Power On/Off Button is pressed within the 30-minute cool down period, heater will run at Max Heat setting, but shut down in 2 seconds with the Power Light Ring flashing. Please repeat the above 4 steps to reset the heater again and ensure to allow sufficient time for the thermostat to cool down. FOR MODELS WITH TIP OVER PROTECTION Tip Over Shut-Off: When the unit is accidentally knocked over, it will instantly shut off and the Power Light Ring will flash. The unit may also shut off if it is moved or bumped. To reset, simply place the heater in an upright position, the Power Light Ring will stop flashing and it will operate normally. NOTE: If unit does not turn on when placed in the upright position, press Power On/Off Button once and heater will resume operation. TROUBLE SHOOTING General Information: Environmental Factors - There are a number of factors that will affect your desired comfort level. These factors can include insulation, open or drafty doors and windows, and outside temperature. Please check and take action if any of these potential problems are affecting your heaters ability to adequately warm your room. Supplemental Heat - Portable electric heaters are intended for supplemental heating of rooms to heat the room you are in and turn down the central heat thermostat. They are not intended to replace central heating systems. Do NOT attempt to repair or adjust any electrical or mechanical functions on this heater. Doing so will void warranty. The inside of the heater contains no user serviceable parts. All servicing should be performed by qualified personnel only. If you have any questions regarding your product or would like to learn more about other Sunbeam® products, please contact our Consumer Service Department at 1-888-264-9669 or visit our website at www.sunbeam.com. TROUBLESHOOTING Troubleshooting for your Heater Trouble Probable Cause Solution • Heater Does ☛ Timer Activated (only applicable on Not Turn On. models with Timer feature). ☛ Tip-over switch engaged (only applicable on models with Tip-over protection). ☛ Manual user reset is activated. ☛ Not plugged in properly. ☛ Electrical outlet does not hold plug in securely. ☛ Thermostat set too low. ☛ Obstruction causing the heater not to operate. ☛ Circuit breaker trips. ✔ Press the Power Button to Turn on the Heater. ✔ Set heater upright on a level surface. ✔ Follow reset instructions listed in this manual. ✔ Ensure plug is properly inserted. Make sure electrical outlet and circuit breaker are working. ✔ Have outlet replaced by a licensed electrician. ✔ Turn the Dial Knob clockwise to the highest temperature setting. ✔ Unplug the heater and remove all obstructions. Position your heater 36 inches (91cm) away from all objects. ✔ Make sure no other high wattage appliances are operating on the same circuit and reset breaker if needed. • Power Light ☛ Auto Safety Shut-off system is Ring is activated when there is potential Flashing or overheat. in some ☛ Tip-over switch engaged (only cases, applicable on models with Tip-over Heater Turns protection). On at Max Heat setting but then Shuts Off in 2 seconds with Power Light Ring Flashing. ✔ Follow Auto Safety Shut-off instructions to reset the heater and allow sufficient time for the heater to cool down before plugging in again. ✔ Set heater upright on a level surface. • Not Enough ☛ Heater is in Low Heat setting. Heat. ☛ Thermostat set too low. ✔ Change setting to Max Heat. ✔ Turn the Dial Knob clockwise to the highest temperature setting. • Heater cycles ON and OFF frequently. ☛ The thermostat automatically turns the heater on and off to maintain selected comfort level. ☛ Every 10-15 minute the heater turns on and runs for a minute. ✔ To make this occur less frequently turn the Dial Knob clockwise to the highest setting. ✔ This is normal operation to ensure the heater is maintaining the room temp accurately. TROUBLESHOOTING Trouble • Remote (if applicable) Does not work. • Heater is Blowing Cold Air. • Fan Speed Doesn't Change. • Unexpected Noise. • Unexpected Smell. Troubleshooting for your Heater Probable Cause Solution ☛ Battery low. ☛ Distance too far. ☛ Control Panel Display dirty. ✔ Change battery (Disc type, 3 volt, CR2025). ✔ Remote works up to 20 feet (6m). ✔ Be sure to point remote at control panel on heater and there are no obstructions. ✔ Make sure display panel is clean. ☛ When the heater is in Thermostat Mode and reaches the set temperature it will automatically perform a 15 second cool down (blowing cold air) to ensure thermostat accuracy. ☛ Unit is in the Fan Only setting. ☛ Power Button may have been pressed to turn off the heater. ✔ Raise the temperature higher or change to Low/Eco-SmartTM or Max heat setting. ✔ Press the Max Heat or Low Heat/Eco-SmartTM Buttons. ✔ Press the Power Button to turn on the heater. ☛ Max Heat and Low Heat/Eco-SmartTM settings control the heat output of the heater and not the fan speed. Fan runs at the same speed on all settings. ✔ Run heater in Max Heat for maximum heat output. ☛ You may hear a popping or crackling sound as the heater heats up. This is normal and safe operation. Once the heater heats up, the crackling sound will go away. ✔ If the noise persists, call Sunbeam customer service at 1-888-264-9669. ☛ There may be an odor or vapor coming from the heater the first time you use it or after prolonged or seasonal storage. ✔ This is normal and is the result of dust or other debris accumulating on the heating element. Make sure the heater is in a well ventilated area and continue running until the odor or vapor goes away. © 2012 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431. Printed In China WARRANTY INFORMATION 1 YEAR LIMITED WARRANTY Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively "JCS") warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes. What are the limits on JCS's Liability? JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction. How to Obtain Warranty Service In the U.S.A. If you have any question regarding this warranty or would like to obtain warranty service, please call 1-888-264-9669 and a convenient service center address will be provided to you. In Canada If you have any question regarding this warranty or would like to obtain warranty service, please call 1-888-264-9669 and a convenient service center address will be provided to you. In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE. Heater Calefactor TRUSTED FOR OVER 100 YEARS DE CONFIABILIDAD CON MÁS DE 100 AÑOS * Fan-Forced Heaters may appear with a different grill design *Los calefactores con impulso de ventilador pueden tener un diseño de rejilla distinto NOTE: A Phillips screwdriver is required for assembly (if applicable). NOTA: Se requiere un desarmador Phillips para el montaje (si corresponde). INSTRUCTION MANUAL PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS MANUAL DE INSTRUCCIONES LEA Y CONSERVE ESTAS INSTRUCCIONES IMPORTANTES APAGADO AUTOMATICO DE SEGURIDAD 5. Se recomienda guardar la unidad en su embalaje original. *CONSEJO: Con el transcurso del tiempo se acumulará polvo en las rejillas delanteras que puede eliminarse con un paño húmedo. APAGADO AUTOMATICO DE SEGURIDAD Este calefactor está equipada con un sistema de seguridad tecnológicamente avanzado y que requiere que el usuario la reactive si se produce un recalentamiento. Si la unidad se recalienta, el sistema la apagará automáticamente y sólo podrá volver a funcionar si el usuario la reactiva manualmente. Si el calefactor se apaga y el anillo de la energía eléctrica titila: 1. Coloque el calefactor en forma vertical. 2. Desenchufe la unidad y espere 30 minutos. 3. Enchufela y vuélvala a operar normalmente. 4. Si el calefactor no funciona normalmente, repita los pasos 1, 2 y 3 de nuevo. NOTA: Si se enchufa el calefactor nuevamente y se presiona el botón Encendido/Apagado durante los 30 minutos del período de enfriamiento, el aparato funcionará en la configuración a Temperatura máxima pero se apagará a los dos segundos y el anillo de energía eléctrica titilará. Para restablecer el calefactor nuevamente, repita los 4 pasos anteriores y asegúrese de que el termostato tenga suficiente tiempo para enfriarse. PARA MODELOS CON PROTECCIÓN CONTRA INCLINACIONES Apagado de inclinación: Cuando la unidad se encuentre accidentalmente inclinada, se apagará de manera inmediata y el anillo de energía eléctrica comenzará a titilar. La unidad también se apagará si se la mueve o golpea. Para restablecerlo, coloque el calefactor en posición vertical, el anillo de energía eléctrica dejará de titilar y funcionará normalmente. NOTA: Si la unidad no se enciende cuando se coloca en posición vertical, presione el botón Encendido/Apagado una vez y el calefactor comenzará a funcionar nuevamente. DIAGNOSTICO DE PROBLEMAS Información general: Factores medioambientales: Hay muchos factores que afectarán su nivel de confort deseado. Estos factores pueden incluir el aislamiento, puertas y ventanas abiertas o con corriente de aire, y la temperatura exterior. Haga una revisión y realice las acciones necesarias si alguno de estos problemas potenciales afectan la capacidad del calefactor para calentar adecuadamente la habitación. Calor complementario: Los calefactores eléctricos portátiles están diseñados para brindar calefacción complementaria a las habitaciones, para calentar la habitación en la que usted se encuentra y bajar el termostato de la central de calefacción. No están diseñados para sustituir los sistemas centrales de calefacción. NO trate de reparar ni ajustar ninguna de las funciones eléctricas o mecánicas de este calefactor. Si lo hace, la garantía quedará anulada. El interior del calefactor no tiene piezas que el usuario pueda reparar. Las reparaciones sólo deberán ser realizadas por personal capacitado. Si tiene preguntas relacionadas con este producto o si está interesado en conocer otros productos Sunbeam®, póngase en contacto con nuestro Departamento de Servicio al Cliente: llame al 1-888-264-9669 o visite nuestro sitio web www.sunbeam.com. Sun_Platform_HH_LCD_12ESM1.indd 1 DIAGNOSTICO DE PROBLEMAS Solución de problemas del calefactor Problema Posible Causa Solución • El calefactor no ☛ El temporizador se encuentra activado ✔ Presione el botón de encendido para encender el enciende. (sólo se aplica a modelos que tengan calefactor. la función Temporizador). ☛ El interruptor contra inclinaciones está ✔ Coloque el calefactor en posición vertical sobre una activado (sólo se aplica a modelos con superficie nivelada. protección contra inclinaciones). ☛ El restablecimiento manual de ✔ Siga las instrucciones de restablecimiento que usuario está activado. aparecen en este manual. ☛ No está conectado correctamente. ✔ Compruebe que el enchufe esté insertado correctamente. Asegúrese de que el tomacorriente y el interruptor de circuito funcionen. ☛ El tomacorriente no sostiene el ✔ Contrate a un eléctrico con licencia para reemplazar enchufe de manera segura. el tomacorriente. ☛ El termostato está en un valor ✔ Gire la perilla con dial en el sentido de las agujas del demasiado bajo. reloj hasta alcanzar la posición de temperatura más alta. ☛ Hay obstrucciones que hacen que el ✔ Desconecte el calefactor y retire las obstrucciones. Coloque calefactor no funcione. el calefactor a 91 cm de distancia de los demás objetos. ☛ El interruptor de circuito está ✔ Compruebe que no haya otros aparatos de alto desactivado. vataje funcionando en el mismo circuito y, si es necesario, restablezca el interruptor. • El círculo luminoso ☛ El sistema de apagado automático se ✔ Siga las instrucciones de apagado de seguridad de encendido está encuentra activado en caso de un automático para reestablecer el calefactor y brindarle destellando o, a sobrecalentamiento potencial. al calefactor suficiente tiempo para que se enfríe veces, el calefactor antes de enchufarlo de nuevo. se enciende en la ☛ El interruptor contra inclinaciones está ✔ Coloque el calefactor en posición vertical sobre una posición de activado (sólo se aplica a modelos con superficie nivelada. máximo calor, protección contra inclinaciones). pero después se apaga en 2 segundos mientras el círculo luminoso de encendido se encuentra destellando. • No hay suficiente ☛ El calefactor está en la posición de calefacción. calor bajo. ☛ El termostato está en un valor bajo. ✔ Cambie la posición a máximo calor. ✔ Gire la perilla con dial en el sentido de las agujas del reloj hasta alcanzar la posición de temperatura más alta. • El calefactor se ☛ El termostato automáticamente enciende ✔ Para que esto ocurra con menos frecuencia, gire la enciende y y apaga el calefactor a fin de mantener el perilla con dial en el sentido de las agujas del reloj apaga con nivel de confort seleccionado. hacia la posición de máximo calor. frecuencia. ☛ Cada 10 o 15 minutos, el calefactor se ✔ Se trata del funcionamiento normal para asegurar que el enciende y funciona durante un minuto. calefactor está manteniendo la temperatura ambiente con precisión. DIAGNOSTICO DE PROBLEMAS Problema • El control remoto (si corresponde) no funciona. • El calefactor sopla aire frío. • La velocidad del ventilador no cambia. • Ruido inesperado. • Olor inesperado. Solución de problemas del calefactor Posible Causa Solución ☛ Tiene poca batería. ✔ Cambie la batería (tipo de descripción, 3 voltios, CR2025). ☛ Está demasiado lejos. ✔ El control remoto funciona hasta 20 pies (6m). ✔ Asegúrese de apuntar el control remoto al panel de control del calefactor y de que no haya ningún obstáculo. ☛ El visor del panel de control está sucio. ✔ Asegúrese de que el visor esté limpio. ☛ Cuando el calefactor se encuentra en modo Termostato y alcanza la temperatura establecida, se enfriará automáticamente durante 15 segundos (sopla aire frío) para asegurar la precisión del termostato. ☛ La unidad se encuentra en la posición Ventilador únicamente. ☛ Es posible que el botón de encendido se haya presionado para apagar el calefactor. ✔ Aumente la temperatura o cambie la posición a calor Bajo/Eco-SmartTM o Máximo. ✔ Presione el botón de Máximo calor o Calor bajo/ Eco-SmartTM. ✔ Presione el botón de encendido para encender el calefactor. ☛ Las posiciones de Máximo calor y Calor bajo/Eco-SmartTM controlan la salida de calor del calefactor y no controlan la velocidad del ventilador. El ventilador funciona a la misma velocidad en todas las opciones. ✔ Haga funcionar el calefactor en la posición de Máximo calor para generar la salida de máximo calor. ☛ Es posible que se escuchen chasquidos ✔ Si el ruido persiste, llame al servicio al cliente o crujidos cuando el calefactor se Sunbeam al 1-888-264-9669. calienta. Esto es parte del funcionamiento normal y seguro. Una vez que el calefactor se caliente, los crujidos cesarán. ☛ Es posible que el calefactor produzca olores o vapores la primera vez que lo utilice o después de haber estado almacenado una temporada. ✔ Esto es normal y es el resultado del polvo u otros residuos que se acumulan en el dispositivo de calefacción. Asegúrese de que el calefactor se encuentre en un área ventilada y que siga funcionando hasta que el olor o vapor desaparezcan. © 2012 Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions. Todos los derechos reservados. Distribuido por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton, Florida 33431. 156284/9100020013493 GCDS-SUN23776-PH Sun_Platform HH_LCD_12ESM1 Impreso en China INFORMACION DE LA GARANTIA GARANTÍA LIMITADA DE 1 AÑO Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, o en Canadá, Sunbeam Corporation (Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, (en forma conjunta, "JCS"), garantiza que por un período de uno año a partir de la fecha de compra, este producto estará libre de defectos de materiales y mano de obra. JCS, a su elección, reparará o reemplazará este producto o cualquier componente del mismo que presente defectos durante el período de garantía. El reemplazo se realizará por un producto o componente nuevo o reparado. Si el producto ya no estuviera disponible, se lo reemplazará por un producto similar de valor igual o superior. Ésta es su garantía exclusiva. No intente reparar o ajustar ninguna función eléctrica o mecánica de este producto. Al hacerlo elimínará ésta garantía. La garantía es válida para el comprador minorista original a partir de la fecha de compra inicial y la misma no es transferible. Conserve el recibo de compra original. Para solicitar servicio en garantía se requiere presentar un recibo de compra. Los agentes y centros de servicio de JCS o las tiendas minoristas que venden productos de JCS no tienen derecho a alterar, modificar ni cambiar de ningún otro modo los términos y las condiciones de esta garantía. Esta garantía no cubre el desgaste normal de las piezas ni los daños que se produzcan como resultado de uso negligente o mal uso del producto, uso de voltaje incorrecto o corriente inapropiada, uso contrario a las instrucciones operativas, y desarme, reparación o alteración por parte de un tercero ajeno a JCS o a un Centro de Servicio autorizado por JCS. Asimismo, la garantía no cubre actos fortuitos tales como incendios, inundaciones, huracanes y tornados. ¿Cuál es el límite de responsabilidad de JCS? JCS no será responsable de daños incidentales o emergentes causados por el incumplimiento de alguna garantía o condición expresa, implícita o legal. Excepto en la medida en que lo prohíba la ley aplicable, cualquier garantía o condición implícita de comerciabilidad o aptitud para un fin determinado se limita, en cuanto a su duración, al plazo de la garantía antes mencionada. JCS queda exenta de toda otra garantías, condiciones o manifestaciones, expresa, implícita, legal o de cualquier otra naturaleza. JCS no será responsable de ningún tipo de daño que resulte de la compra, uso o mal uso del producto, o por la imposibilidad de usar el producto, incluidos los daños incidentales, especiales, emergentes o similares, o la pérdida de ganancias, ni de ningún incumplimiento contractual, sea de una obligación esencial o de otra naturaleza, ni de ningún reclamo iniciado contra el comprador por un tercero. Algunas provincias, estados o jurisdicciones no permiten la exclusión o limitación de los daños incidentales o emergentes ni las limitaciones a la duración de las garantías implícitas, de modo que es posible que la exclusión o las limitaciones antes mencionadas no se apliquen en su caso. Esta garantía le otorga derechos legales específicos y es posible que usted tenga otros derechos que varían de un estado, provincia o jurisdicción a otro. Cómo solicitar el servicio en garantía En los Estados Unidos Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, llame al 1 (888) 264-9669 y podrá obtener la dirección del centro de servicio que le resulte más conveniente. En Canadá Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, llame al 1 (888) 264-9669 y podrá obtener la dirección del centro de servicio que le resulte más conveniente. En los Estados Unidos, esta garantía es ofrecida por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Ratón, Florida 33431. En Canadá, esta garantía es ofrecida por Sunbeam Corporation (Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, 20 B Hereford Street, Brampton, Ontario L6Y 0M1. Si usted tiene otro problema o reclamo en conexión con este producto, por favor escriba al Departamento de Servicio al Consumidor. POR FAVOR NO DEVUELVA ESTE PRODUCTO A NINGUNA DE ESTAS DIRECCIONES NI AL LUGAR DE COMPRA. ® GO ONLINE NOW to http://www.sunbeam.com/SBMCLG201 to receive a FREE GIFT OR PROMO CODE*. It's our "thanks" to you for being a Sunbeam® customer. -You will also get access to special sale items & promotions on a full assortment of Sunbeam® products. HURRY & SIGN UP TODAY! *While supplies last; subject to availability. ® INGRESE AHORA MISMO al sitio http://www.sunbeam.com/SBMCLG201 para recibir un OBSEQUIO GRATIS O UN CÓDIGO DE PROMOCIÓN*. Es nuestra manera de decirle "gracias" por ser cliente de Sunbeam®. -También obtendrá acceso a promociones y artículos de venta especiales de una completa variedad de productos de Sunbeam®. ¡APRESÚRESE Y REGÍSTRESE HOY MISMO! *Hasta agotar el stock; sujeto a disponibilidad 3/20/12 9:24 AM