Symphonic WF206 Owner's Manual - Page 2
Preparation For Use, Operations - remote
View all Symphonic WF206 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
PREPARATION FOR USE CONNECTIONS Plug the incoming cable into the ANT. jack on the rear of the TV. Cable TV signal OR Antenna Rear of this TV Incoming cable from home Antenna / Cable Company (No Cable Box) Cable Box or Satellite Box* OR OUT IN ANT. ANT. You can enter into Video mode from Game mode by adjusting a Picture control. 1 To use external input 2 To cancel Game mode only GAME GAME MENU m VOL [-] GAME MODE [+] OFF ON Picture: GAME (ON) Input: External Select "PICTURE" After 10 seconds VIDEO Incoming cable from Cable Company or Satellite Antenna Cables not included *Note (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Note: • For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack before moving the unit. [EXTERNAL CONNECTION] AUDIO/VIDEO input ex. Video Camera Video Game Audio Cable Rear of this TV (OUT) (IN) AUDIO VIDEO (OUT) (IN) Video Cable INSTALLING THE BATTERIES 1 2 3 Install two AAA batteries (not supplied) matching the polarity indicated inside battery compartment of the remote control. [BATTERY PRECAUTIONS] • Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device. • Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones. • If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. • Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. INITIAL SETUP When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed. The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is completed. 1 Select the desired language according to the screen indication. After that, the TV performs "AUTO PRESET CH" to scan channels available for the broadcasting in your area. SELECT LANGUAGE ENGLISH NEXT:PRESS CHK ESPAÑOL DESPUÉS:PRESIONE CHL FRANÇAIS APRÈS:PRESSEZ VOLK - INITIAL SETUP - PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. THEN PRESS CH K, IN ORDER TO PERFORM "AUTO PRESET CH". 2 If the TV screen shows - HELPFUL HINTS - 1. PLEASE CHECK TO SEE IF snow noise and there THE ANTENNA/CABLE/ SATELLITE IS PROPERLY is no operation for CONNECTED. 2. DID YOU PERFORM "AUTO PRESET CH" ? more than 10 seconds, 3. PLEASE REFER TO FRONT PAGE OF THE OWNER'S "HELPFUL HINTS" MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION. appears. Follow the instructions listed on the screen. Picture: Customized Input: External 3 To return to TV channel 15 GAME 2 times OPERATIONS REMOTE CONTROL AND FRONT PANEL FUNCTION IR transmitter To send infrared ray (IR) signal POWER button To turn TV on/off VOL X/Y buttons To adjust volume To decide the command of settings MENU button To view on-screen menu MUTE button To mute sound DISPLAY button To display CH No./Audio Status GAME POWER o CH m p VOL n 1 2 3 4 5 6 7 8 9 MENU 0 +100 MUTE SLEEP CH RET DISPLAY GAME button Press to set the Game mode. CH K/L buttons To select channels and move up/down through menu items Channel number buttons Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button Press to select cable channels higher than 99. SLEEP button To set Sleep Timer CH RET button To return to previous channel Note: ● You can test if the remote control sends out the infrared signal with an AM radio. (Refer to "TROUBLESHOOTING GUIDE".) When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel. Notes: ● In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again. ● If those settings do not work properly, please call our help line on the front page of this owner's manual. SELECTING AUDIO/VIDEO INPUT You can select external input jacks by pressing [GAME] on the remote control. 1 To use external input 2 To return to TV channel GAME 15 GAME GAME Infrared Sensor Window POWER button To turn TV on/off CHANNEL ▲/▼ buttons To select channels VOLUME X/Y buttons To adjust volume MENU button To view on-screen menu Note: ● If some digits appear in the corner of the screen when the unit is turned on for the first time, press [POWER] without unplugging the power cord. Picture: GAME (ON) Input: External In the Game mode, you can use input jacks with suitable picture adjustments for video games. Notes: ● If you press [GAME] when the TV is off, the TV turns on and enters in Game mode. ● If you adjust another picture control while in Game mode, this mode will automatically be canceled.