Symphonic WF20L6 Owner's Manual - Page 2

PREPARATION FOR USE UNPACKING The stand of this TV is folded when you purchased. Place this TV face-down on a flat surface covered with the soft cloth. Bend the stand slowly to forward until it clicks. Do not bend from this side. If you want to fold the stand again, insert a thin rod into the hole in the right side of the stand as illustrated, bend the stand backward while you keep pushing the hole. CONNECTIONS Plug the incoming cable into the ANT jack on the rear of the TV. Cable TV signal OR Antenna Rear of this TV Incoming cable from home Antenna / Cable Company (No Cable Box) Cable Box or Satellite Box* OR OUT IN VIDEO2 R AUDIO L COMPONENT Y Pb Pr R AUDIO L V I D EO 1 V ID E O S-VIDEO ANT HEAD PHONE ANT Incoming cable from Cable Company or Satellite Antenna Cables not included *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Note: • For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack before moving the unit. [EXTERNAL CONNECTION] VIDEO1 input ex. (OUT) Audio Cable (OUT) Video Cassette Recorder HEADPHONE jack Video Cable OR (OUT) S-Video Cable ex. (OUT) (IN) (IN) (IN) R AUDIO L V ID EO1 VIDE O S-VIDEO ANT (IN) HEAD PHONE Rear of this TV VIDEO2 R AUDIO L COMPONENT Y Pb Pr R AUDIO L V I DE O 1 V I D E O S-VIDEO ANT HEAD PHONE Headphone Notes: ● The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment. ● The S-VIDEO jack is given priority over the VIDEO jack. VIDEO2 input ex. Video Camera (OUT) Audio Cable Video Game (OUT) Component Video Cable (IN) (IN) VIDEO2 R AUDIO L COMPONENT Y Pb Pr Rear of this TV VIDEO2 R AUDIO L COMPONENT Y Pb Pr R AUDIO L V I D EO 1 VID E O S-VIDEO ANT HEAD PHONE Notes: ● This TV can accept 480p / 480i / simplified 1080i video signal. ● Simplified 1080 video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal. INITIAL SETUP When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed. The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is completed. 1 Select the desired SELECT LANGUAGE language according to the screen indication. After that, the TV ENGLISH NEXT:PRESS CHK ESPAÑOL DESPUÉS:PRESIONE CHL FRANÇAIS APRÈS:PRESSEZ VOLX performs "AUTO PRESET CH" to scan channels available for the broadcasting in your area. - INITIAL SETUP - PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. THEN PRESS CH K, IN ORDER TO PERFORM "AUTO PRESET CH ". 2 If the TV screen shows - HELPFUL HINTS - 1. PLEASE CHECK TO SEE IF THE snow noise and there is ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED. no operation for more 2. DID YOU PERFORM "AUTO PRESET CH" ? 3. PLEASE REFER TO FRONT PAGE OF THE OWNER'S MANUAL OR REAR PANEL FOR than 5 seconds, SUPPORT LINE INFORMATION. "HELPFUL HINTS" appears. Follow the instructions listed on- screen. When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel. Notes: ● In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again. ● If those settings do not work properly, please call our help line on the front page of this owner's manual. SELECTING AUDIO/VIDEO INPUT When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input mode changes by pressing the button as following: INPUT SELECT TV channel VIDEO1 VIDEO2 TILT STAND Tilt Stand Adjust the stand to change the angle of TV (-5° ~ 10°). -5° 10° OPERATIONS REMOTE CONTROL AND TOP PANEL FUNCTION IR transmitter To send infrared ray (IR) signal POWER button To turn TV on/off VOL X/Y buttons To adjust volume To decide the command of settings MENU button To view on-screen menu MUTE button To mute sound DISPLAY button To display CH No./Audio Status INPUT SELECT POWER o CH m p VOL n 1 2 3 4 5 6 7 8 9 MENU 0 +100 MUTE SLEEP CH RET DISPLAY INPUT SELECT button To select TV or external input CH K/L buttons To select channels and move up/down through menu items Channel number buttons Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button Press to select cable channels higher than 99. SLEEP button To set Sleep Timer CH RET button To return to previous channel Note: ● You can test if the remote control sends out the infrared signal with an AM radio. (Refer to "TROUBLESHOOTING GUIDE".) MENU MENU button To view on-screen menu VOLUME X/Y buttons To adjust volume CHANNEL K/L buttons To select channels SELECT button To select TV or external input POWER button To turn TV on/off VOLUME CHANNEL SELECT POWER INSTALLING THE BATTERIES 1 2 3 Install two AAA batteries (supplied) matching the polarity indicated inside battery compartment of the remote control. [BATTERY PRECAUTIONS] • Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device. • Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones. • If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. • Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. Infrared Sensor Window Note: ● If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord.