TEAC AP-505 Firmware Update Manual - Page 1

TEAC AP-505 Manual

Get TEAC AP-505 PDF manuals and user guides View all TEAC AP-505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Z Firmware update manual Model covered AP-505 Equipment used Windows computer (with built-in USB 2.0 port) Micro USB cable oo Cables designed only for charging cannot be used. Always use a micro USB cable that supports data transmission. Supported operating systems Windows 7 (32/64-bit) Windows 8 (32/64-bit) Windows 8.1 (32/64-bit) Windows 10 (32/64-bit) (as of September 2020) 2. Install the DFU driver Set the unit's STANDBY/ON switch to STANDBY, and begin the following operations before connecting it with the computer. NOTE oo After installing the DFU driver on the computer once, installing it again will not be necessary. If installation is complete, proceed to "3. Update the firmware". oo The screens used in this example are from Windows 10. 1 Uncompress the downloaded file. The following files will be created. oo Win_DFU_driver.exe oo AP505_updater_xxxx.exe (xxxx is the firmware version) 2 Double-click Win_DFU_driver.exe, and press the Enter key. 1. Check the firmware version 1 Put the unit into standby, and disconnect everything except the power cord from it. 2 Turn the unit on. 3 Switch the INPUT SELECTOR on the back of the unit three times rapidly. The level meters show the firmware version. Version 1.00 1.01 1.02 1.03 LEFT −40 dB 0 dB 0 dB 0 dB RIGHT −40 dB 0 dB NOTE If a "User Account Control" pop-up message appears during installation, click "Yes". 3 When the Device Driver Installation Wizard appears, click "Next". 4 Click "Finish". Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Other company names and product names in this document are the trademarks or registered trademarks of their respective owners. Continued on the next page e 1

  • 1
  • 2
1
Z
Firmware update manual
Continued on the next page
e
Model covered
AP-505
Equipment used
Windows computer (with built-in USB 2.0 port)
Micro USB cable
o
Cables designed only for charging cannot be used. Always use a
micro USB cable that supports data transmission.
Supported operating systems
Windows 7 (32/64-bit)
Windows 8 (32/64-bit)
Windows 8.1 (32/64-bit)
Windows 10 (32/64-bit)
(as of September 2020)
1. Check the firmware version
1
Put the unit into standby, and disconnect
everything except the power cord from it.
2
Turn the unit on.
3
Switch the INPUT SELECTOR on the back of the
unit three times rapidly.
The level meters show the firmware version.
Version
LEFT
RIGHT
1.00
−40 dB
−∞
1.01
0 dB
−∞
1.02
0 dB
−40 dB
1.03
0 dB
0 dB
2. Install the DFU driver
Set the unit’s STANDBY/ON switch to STANDBY, and begin the fol-
lowing operations before connecting it with the computer.
NOTE
o
After installing the DFU driver on the computer once, installing it
again will not be necessary. If installation is complete, proceed to
“3. Update the firmware”.
o
The screens used in this example are from Windows 10.
1
Uncompress the downloaded file.
The following files will be created.
o
Win_DFU_driver.exe
o
AP505_updater_xxxx.exe (xxxx is the firmware version)
2
Double-click Win_DFU_driver.exe, and press
the Enter key.
NOTE
If a “User Account Control” pop-up message appears during
installation, click “Yes”.
3
When the Device Driver Installation Wizard
appears, click “Next”.
4
Click “Finish”.
Microsoft and Windows are either registered trademarks or trade-
marks of Microsoft Corporation in the United States and/or other
countries.
Other company names and product names in this document are
the trademarks or registered trademarks of their respective owners.