TEAC DP-008 DP-008 version 1.01 release notes
TEAC DP-008 Manual
 |
View all TEAC DP-008 manuals
Add to My Manuals
Save this manual to your list of manuals |
TEAC DP-008 manual content summary:
- TEAC DP-008 | DP-008 version 1.01 release notes - Page 1
capacity of the SD card was filled, I/F Error appeared and recording did not complete correctly in some cases. This has been fixed. Confirmation of firmware version Confirm the firmware version of your DP-008 before conducting a firmware update. 1 Turn the unit's power ON. 2 When the Home Screen is - TEAC DP-008 | DP-008 version 1.01 release notes - Page 2
"Confirmation of firmware version" instructions above to check that the System Version is now the most recent version of the firmware. This completes the procedure for updating this unit. 10 Connect to a computer with USB and delete the firmware update from the unit's UTILITY folder. 2 TASCAM DP-008
-
1 -
2
 |
 |
TASCAM DP-008
1
Updates
Always use the most recent firmware for this device.
Please visit the TASCAM web site at http://tascam.com/ to
check for the latest firmware.
Maintenance items
V1.01 fixes
If recording was conducted until the capacity of the SD
card was filled,
I/F Error
appeared and recording
did not complete correctly in some cases. This has been
fixed.
Confirmation of firmware version
Confirm the firmware version of your DP-008 before
conducting a firmware update.
1
Turn the unit’s power ON.
2
When the Home Screen is open, press the MENU
key to open the
MENU
screen.
3
Use the DATA wheel to select the
INFORMATION
item and press the F4 (
¥
) key to open the
INFORMATION
screen
SONG (1/3)
page.
4
Use the F3 (
PREV
) and F4 (
NEXT
) keys to open
the
F/W (3/3)
page.
If the
System Version
shown here is the same
or newer than the firmware version that you planned
to update to, then there is no need to update it.
Firmware update procedures
CAUTION
When updating the firmware, be sure that the batteries
have sufficient charge or power the unit using a TASCAM
PS-P520 AC adaptor (sold separately).
The program has been set so that the update will not be
conducted if battery power is insufficient.
1
Download the most recent firmware from the
TASCAM web site (http://tascam.com/). If the file
that you have downloaded is compressed in ZIP
format, for example, decompress it.
2
Turn the unit’s power ON and use the included
USB cable to connect it with a computer. This unit
will be recognized as an external drive (external
storage device) by the computer.
3
Copy the downloaded firmware (DP008-48.101 for
V1.01) to the
UTILITY
folder on the DP-008.
4
After copying has completed, disconnect the
unit from the computer following the correct
procedures, and turn the unit power OFF.
5
While pressing and holding both the REPEAT and
UN/REDO keys, turn the unit power ON.
The unit starts up in update mode, and the update file
appears on the screen.
CAUTION
If this screen does not appear, turn the power OFF.
•
Then while pressing and holding both the
REPEAT
and
UN/REDO
keys, turn the unit’s power ON again.
Continue to press and hold the
REPEAT
and
UN/REDO
keys firmly until this screen appears.
When firmware has been copied to this unit’s
•
UTILITY
folder from a Mac, in addition to the firmware file itself,
another file with “._” added to the beginning of the
firmware name is also shown. Use the file without the
“._” at the beginning of the name.
NOTE
This screen shows a list of the firmware update files
•
inside the
UTILITY
folder of the unit. Also, the screen
shows the firmware copied at Step 3 above.
No
Update File
appears if there is no update file in
the
UTILITY
folder.
The screen shown is an example. The actual display
•
differs.
DP-008
Release Notes
D01155100A