TP-Link T1500G-10MPS T1500G-10MPSUN V1 CLI Reference Guide
TP-Link T1500G-10MPS Manual
 |
View all TP-Link T1500G-10MPS manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1500G-10MPS manual content summary:
- TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 1
CLI Guide JetStream 8-Port Gigabit Smart PoE+ Switch with 2 SFP Slots T1500G-10MPS REV1.0.0 1910011909 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 3
Parameter Format 15 Chapter 2 User Interface 16 2.1 enable ...16 2.2 enable-admin ...16 2.3 service password-encryption 17 2.4 enable password...18 2.5 enable secret ...19 2.6 configure ...20 2.7 exit ...20 2.8 end ...21 2.9 history ...21 2.10 history clear ...22 Chapter - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 4
access-control port-based 47 6.6 telnet ...48 6.7 show user account-list 48 6.8 show user configuration 49 6.9 show telnet-status...49 Chapter 7 HTTP and HTTPS Commands 51 7.1 ip http server ...51 7.2 ip http max-users ...52 7.3 ip http session timeout 53 7.4 ip http secure - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 5
key 58 7.11 show ip http configuration 59 7.12 show ip http secure-server 59 Chapter 8 Binding Table Commands 61 8.1 ip source binding ...61 8.2 ip dhcp snooping ...62 8.3 ip dhcp snooping vlan 63 8.4 ip dhcp snooping information option 64 8.5 ip dhcp snooping information strategy - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 6
ip ssh server ...91 12.2 ip ssh version...91 12.3 ip ssh algorithm ...92 12.4 ip ssh timeout...93 12.5 ip ssh max-client ...93 12.6 ip ssh download ...94 12.7 remove public-key ...95 12.8 show ip dot1x guest-vlan(interface 104 dot1x port-control...104 dot1x port-method 105 show dot1x global 106 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 7
119 show mac address-table security 120 Chapter 15 System Configuration Commands 121 15.1 15.2 15.3 15.4 15.5 15 18 15.19 15.20 15.21 system-time manual 121 system-time ntp ...121 system-time dst location ...127 contact-info ...127 ip address ...128 ip address-alloc ...129 reset ...130 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 8
141 show cpu-utilization 141 show memory-utilization 142 Chapter 16 Ethernet Configuration Commands 143 16.1 16.2 16.3 16.4 16.5 16.6 16.7 149 show interface status 150 show interface counters 151 show interface configuration 151 show storm-control 152 show bandwidth ...153 Chapter 17 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 9
show monitor session 164 Chapter 19 Port Isolation Commands 165 19.1 port isolation ...165 19.2 show port isolation interface 166 Chapter 20 Loopback policy 181 show access-list bind 182 Chapter 22 PoE Commands 183 22.1 power inline consumption (global 183 22.2 power profile ...183 22.3 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 10
inline priority 190 power inline supply 191 power inline profile 191 power inline time-range 192 show power inline 193 show power inline configuration interface 193 show power inline information interface 194 show power profile 194 show power holiday 195 show power time-range 195 Chapter - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 11
vlan-config 220 ip igmp snooping vlan-config (router-ports-forbidden 222 ip igmp snooping multi-vlan-config 223 ip igmp snooping multi-vlan-config (router-ports-forbidden 224 ip igmp snooping multi-vlan-config (source-ip-replace 225 ip igmp snooping querier vlan 225 ip igmp snooping querier - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 12
239 snmp-server user...241 snmp-server community 242 snmp-server host...243 snmp-server engineID 245 snmp-server traps snmp 245 snmp-server traps link-status 246 snmp-server traps 247 snmp-server traps vlan 248 rmon history ...249 rmon event...250 rmon alarm...251 rmon statistics...252 show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 13
aaa accounting dot1x default 282 show aaa authentication 283 show aaa accounting 284 line telnet ...284 login authentication(telnet 285 line ssh...285 login authentication(ssh 286 enable authentication(telnet 287 enable authentication(ssh 287 ip http login authentication 288 ip http enable - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 14
in this Guide stands for T1500G-10MPS JetStream 8-Port Gigabit Smart PoE+ Switch with 2 SFP Slots without any explanation. Overview of this Guide Chapter 1: information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). Chapter 6: User - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 15
and System IP, reboot and reset the switch, upgrade the switch system and commands used for cable test. Chapter 16: Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and Storm Control for enthernet ports. Chapter 17 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 16
Chapter 25: SNMP Commands Provide information about the commands used for configuring the SNMP (Simple Network Management Protocol) functions. Chapter 26: LLDP Commands Provide information about the commands used for configuring LLDP function. Chapter 27: AAA Commands Provide information about the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 17
through an Ethernet port. 1.1.1 Logon by Telnet To log on to the switch by a Telnet connection, please take the following steps: 1. Click Start and type in cmd in the Search programs and files window and press the Enter button. Figure 1-1 Run Window 2. Telnet the switch's IP address (factory setting - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 18
to set up an SSH connection: Password Authentication Mode: It requires username and password, which are both admin by default. Key Authentication Mode: It requires a public key for the switch and a private key for the SSH client software. You can generate the public key and the private key through - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 19
Figure 1-5 Enable SSH function Password Authentication Mode 1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type. Figure 1-6 SSH Connection Config 6 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 20
, and then enter enable to enter Privileged EXEC Mode, so you can continue to configure the switch. Figure 1-7 Log on the Switch Key Authentication Mode 1. Select the key type and key length, and generate SSH key. Figure 1-8 Generate SSH Key Note: 1. The key length is in the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 21
key is successfully generated, please save the public key and private key to a TFTP server. Figure 1-9 Save the Generated Key 3. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows: Figure 1-10 Download the Public Key 8 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 22
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading can not be interrupted. 4. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login. Figure 1-11 SSH Connection Config 9 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 23
downloaded. Figure 1-13 Log on the Switch 1.2 CLI Command Modes The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and VLAN Configuration Mode. Interface Configuration Mode can also be divided into Interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 24
command to enter this mode from User EXEC mode. Global Configuration Mode Use the configure command to enter this mode from Privileged EXEC mode. T1500G-10MPS> T1500G-10MPS# T1500G-10MPS(config)# Use the exit command to disconnect the switch. Use the enable command to access Privileged EXEC mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 25
port, interface port-channel lagid or interface range gigabitEthernet port-list command to enter this mode from Global Configuration mode. T1500G-10MPS(config-if)# or T1500G-10MPS Configuration mode. T1500G-10MPS(config-if)# or T1500G-10MPS(config-if-range)# Use the switchport command to switch - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 26
next mode T1500G-10MPS(config-vlan)# Use the end command or press Ctrl+Z to return to Privileged EXEC mode. Enter the exit command or the # command to return to Global configuration mode. Note: 1. The user is automatically in User EXEC Mode after the connection between the PC and the switch is - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 27
Privileged EXEC mode from User EXEC mode by using the enable command. In default case, no password is needed. In Global Configuration Mode, you can configure password for Admin level by enable password command. Once password is configured, you are required to enter it to access Privileged EXEC mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 28
as follows: MAC address must be enter in the format of xx:xx:xx:xx:xx:xx. One or several values can be typed for a port-list or a vlan-list using comma to separate. Use a hyphen to designate a range of values, for instance,1/0/1,1/0/3-5,1/0/7 indicates choosing - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 29
EXEC Mode from User EXEC Mode: T1500G-10MPS>enable Enter password： T1500G-10MPS# 2.2 enable-admin Description The enable-admin command is used to evaluate the current log-in user to the Admin access level. Syntax enable-admin Command Mode Privileged Configuration Mode Privilege Requirement None. 16 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 30
123 to gain the administrative privilege. T1500G-10MPS#enable-admin Password:123 T1500G-10MPS# 2.3 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the configuration is written, using the symmetric - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 31
and sixteen special characters By default, it is empty. 7 -- Indicates a symmetric encrypted password with fixed length will follow. encrypted-password -- A symmetric encrypted password with fixed length, which you can copy from another switch's configuration file. After the encrypted password - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 32
EXEC Mode: T1500G-10MPS(config)#enable password 0 admin 2.5 enable secret Description The enable secret command is used to set a secret password, which is using an MD5 encryption algorithm, for users to access Privileged EXEC Mode from User EXEC Mode. To return to the default configuration, please - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 33
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Access Global Configuration Mode from Privileged EXEC Mode: T1500G-10MPS# configure T1500G-10MPS(config)# 2.7 exit Description The exit command is used to return to the previous Mode from the current - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 34
to these commands. Example Return to Privileged EXEC Mode from Interface Configuration Mode: T1500G-10MPS(config-if)#end T1500G-10MPS# 2.9 history Description The history command is used to show the latest 20 commands you entered in the current mode since the switch is powered. Syntax history 21 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 35
Command Mode Privileged EXEC Mode and any Configuration Mode Privilege Requirement None. Example Show the commands you have entered in the current mode: T1500G-10MPS (config)# history 1 history 2.10 history clear Description The history clear command is used to clear the commands you have entered in - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 36
) technology is developed for the switch to divide the LAN into multiple Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN 2-10 and VLAN 100: T1500G-10MPS(config)# vlan 2-10,100 Delete VLAN 2: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 37
802.1Q VLAN ID, ranging from 1 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN Interface 2: T1500G-10MPS(config)# interface vlan 2 3.3 name Description The name command is used to - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 38
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add port 4 it to VLAN 2 and configure the type of port 1/0/4 as tagged: T1500G-10MPS(config)# interface gigabitEthernet 1/0/4 T1500G-10MPS(config-if)# switchport general allowed vlan 2 tagged 25 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 39
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the PVID of port 1/0/2 as 2: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 40
of IEEE 802.1Q VLAN. Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the brief information of IEEE 802.1Q VLAN: T1500G-10MPS(config)# show vlan brief 3.8 show vlan Description The show vlan command is used to display the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 41
[ gigabitEthernet port | port-channel lagid ] Parameter port -- The port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the VLAN configuration information of all ports and LAGs: T1500G-10MPS(config)# show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 42
1Q VLAN ID, ranging from 2 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Voice VLAN function for VLAN 10: T1500G-10MPS(config)# voice vlan 10 4.2 voice vlan aging Description The - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 43
Set the aging time for the Voice VLAN as 1 minute: T1500G-10MPS(config)# voice vlan aging 1 4.3 voice vlan priority Description The voice vlan priority command is used to configure the priority for the Voice VLAN. To restore to the default priority, please use no voice vlan priority command. Syntax - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 44
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a Voice VLAN OUI described as TP-Phone with the OUI address 00:11:11:11:11:11 and the mask address FF:FF:FF:00:00:00: T1500G-10MPS(config)#voice - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 45
, Operator and Power User level users have access to these commands. Example Configure the port 1/0/3 to operate in the auto voice VLAN mode: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# switchport voice vlan mode auto 4.6 switchport voice vlan security Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 46
. Example Enable port 1/0/3 for the Voice VLAN security feature: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# switchport voice vlan security 4.7 show voice vlan Description The show voice vlan command is used to display the global configuration information of Voice - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 47
LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the Voice VLAN configuration information of all ports and LAGs: T1500G-10MPS(config)# show voice vlan switchport 34 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 48
Display the Voice VLAN configuration information of port 1/0/2: T1500G-10MPS(config)# show voice vlan switchport gigabitEthernet 1/0/2 35 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 49
Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 50
range gigabitEthernet 1/0/2-4 T1500G-10MPS(config-if-range)# channel-group 1 mode on 5.2 port-channel load-balance Description The port-channel load-balance command is used to configure the Aggregate Arithmetic for LAG. To return to the default configurations, please use no port-channel load-balance - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 51
Arithmetic for LAG as "src-dst-ip": T1500G-10MPS(config)# port-channel load-balance src-dst-ip 5.3 lacp system-priority Description The lacp system-priority command is used to configure the LACP system priority globally. To return to the default configurations, please use no lacp system-priority - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 52
by default. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the LACP port priority as 1024 for ports 1-3: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 53
-group-num -- The EtherChannel Group number, ranging from 1 to 6. By default, it is empty, and will display the information of all EtherChannel Groups. detail Any Configuration Mode Privilege Requirement None. Example Display the detailed information of EtherChannel Group 1: T1500G-10MPS(config)# - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 54
. neighbor -- The neighbor LACP information. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the internal LACP information of EtherChannel Group 1: T1500G-10MPS(config)# show lacp 1 internal 5.8 show lacp sys-id Description The show lacp - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 55
Example Display the LACP system priority: T1500G-10MPS(config)# show lacp sys-id 42 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 56
settings of different functions without the right to edit or modify. It is "admin" by default. For more details about privilege restrictions, please refer to the Privilege Requirement part in each password with fixed length, which you can copy from another switch's configuration file. After the 43 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 57
encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Add and enable a new admin user named "tplink", of which the password is "admin" and unencrypted: T1500G-10MPS(config)#user name tplink - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 58
form. T1500G-10MPS(config)#user name tplink privilege admin secret 0 admin 6.3 user access-control ip-based Description The user access-control ip-based command is used to limit the IP-range of the users' access. Only the users within the IP-range you set here are allowed to access the switch. To - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 59
are enabled by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the access-control of the user whose IP address is 192.168.0.148: T1500G-10MPS(config)# user access-control ip-based 192.168 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 60
are enabled by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to access the switch: T1500G-10MPS(config)# user - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 61
Admin and Operator level users have access to these commands. Example Configure that only the users connected to ports 2-6 are allowed to access the switch: T1500G-10MPS(config)# user access-control port-based interface gigabitEthernet 1/0/2-6 6.6 telnet Description The telnet enable command is used - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 62
commands. Example Display the information of the current users: T1500G-10MPS(config)# show user account-list 6.8 show user configuration Description The show user configuration command is used to display the security configuration information of the user authentication information and the access - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 63
Syntax show telnet-status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display whether the Telnet function is enabled: T1500G-10MPS(config)# show telnet-status 50 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 64
by default. The HTTP and HTTPS server function cannot be disabled at the same time. Syntax ip http server no ip http server Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable the HTTP function: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 65
. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the maximum number of the Admin, Operator, Power User and User logging on to the HTTP server as 5, 2, 2, and 1: T1500G-10MPS(config)# ip http max-users - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 66
30 in minutes. By default, the value is 10. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the timeout time of the HTTP server connection as 15 minutes: T1500G-10MPS(config)# ip http session timeout 15 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 67
: T1500G-10MPS(config)# no ip http secure-server 7.5 ip http secure-protocol Description The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports SSLv3 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 68
switch supports all these ciphersuites. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the ciphersuite to be used for encryption over the SSL connection as 3des-ede-cbc-sha: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 69
the HTTPS server as 5, 2, 2, and 1: T1500G-10MPS(config)# ip http secure-max-users 5 2 2 1 7.8 ip http secure-session timeout Description The ip http secure-session timeout command is used to configure the connection timeout of the HTTPS server. To restore to the default timeout time, please use no - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 70
in minutes. By default, the value is 10. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the timeout time of the HTTPS server connection as 15 minutes: T1500G-10MPS(config)# ip http secure - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 71
of fe80::1234 T1500G-10MPS(config)# ip http secure-server download certificate ssl-cert ip-address fe80::1234 7.10 ip http secure-server download key Description The ip http secure-server download key command is used to download an SSL key to the switch from TFTP server. Syntax ip http secure-server - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 72
from TFTP server with the IP address of fe80::1234 T1500G-10MPS(config)# ip http secure-server download key ssl-key ip-address fe80::1234 7.11 show ip http configuration Description The show ip http configuration command is used to display the configuration information of the HTTP server, including - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 73
Syntax show ip http secure-server Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of SSL: T1500G-10MPS(config)# show ip http secure-server 60 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 74
Inspection to filter the packets. 8.1 ip source binding Description The ip source binding command is used to bind the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port number together in the condition that - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 75
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind an ACL entry with the IP 192.168.0.1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 5 manually. And then enable the entry for the ARP detection: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 76
snooping function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Snooping function on VLAN 1,4,6-7: T1500G-10MPS(config)#ip dhcp snooping vlan 1,4,6-7 63 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 77
Enable the Option 82 function of DHCP Snooping on port 1/0/1: T1500G-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information option 8.5 ip dhcp snooping information strategy Description The ip dhcp snooping information strategy command is used to select - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 78
then send out on port 1/0/1: T1500G-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information strategy replace 8.6 ip dhcp snooping information remote-id Description The ip dhcp snooping information remote-id command is used to configure the customized sub - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 79
users have access to these commands. Example Configure the customized sub-option Remote ID for the Option 82 as tplink on port 1/0/1: T1500G-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information remote-id tplink 8.7 ip dhcp snooping information circuit-id - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 80
users have access to these commands. Example Configure the Gigabit Ethernet port 1/0/2 to be a Trusted Port: T1500G-10MPS(config)#interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)#ip dhcp snooping trust 8.9 ip dhcp snooping mac-verify Description The ip dhcp snooping mac-verify command is used - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 81
1/0/2 T1500G-10MPS(config-if)#ip dhcp snooping mac-verify 8.10 ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets. The excessive DHCP packets will be discarded. To restore to the default configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 82
/ interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the rate limit of DHCP Decline packets as 20 packets per second on Gigabit Ethernet port 1/0/2: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 83
binding Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IP-MAC-VID-PORT binding table: T1500G-10MPS(config)#show ip source binding 8.13 show ip dhcp snooping Description The show ip dhcp snooping command is used to display the running - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 84
Requirement None. Example Display the DHCP Snooping configuration of all Ethernet ports and LAGs: T1500G-10MPS#show ip dhcp snooping interface Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5: T1500G-10MPS#show ip dhcp snooping interface gigabitEthernet 1/0/5 8.15 show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 85
-- The Ethernet port number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCP snooping option 82 configuration of all Ethernet ports and port channels: T1500G-10MPS#show ip dhcp snooping - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 86
users have access to these commands. Example Enable the ARP Detection function globally: T1500G-10MPS(config)#ip arp inspection 9.2 ip arp inspection trust Description The ip arp inspection trust command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 87
access to these commands. Example Configure the Gigabit Ethernet ports 1/0/2-5 as the Trusted Port: T1500G-10MPS(config)#interface range gigabitEthernet 1/0/2-5 T1500G-10MPS(config-if-range)#ip arp inspection trust 9.3 ip arp inspection(interface) Description The ip arp inspection command is used - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 88
the arp defend function for the Gigabit Ethernet ports 1/0/2-6: T1500G-10MPS(config)#interface range gigabitEthernet 1/0/2-6 T1500G-10MPS(config-if-range)#ip arp inspection 9.4 ip arp inspection limit-rate Description The ip arp inspection limit-rate command is used to configure the ARP speed of - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 89
Restore Gigabit Ethernet port 1/0/5 to the ARP transmit status: T1500G-10MPS(config)#interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)#ip arp inspection recover 9.6 show ip arp inspection Description The show ip arp inspection command is used to display the ARP detection global configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 90
None. Example Display the configuration of Gigabit Ethernet port 1/0/1: T1500G-10MPS(config)#show ip arp inspection interface gigabitEthernet 1/0/1 Display the configuration of all Ethernet ports: T1500G-10MPS(config)#show ip arp inspection interface 9.8 show ip arp inspection statistics Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 91
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the number of the illegal ARP packets received: T1500G-10MPS(config)#show ip arp inspection statistics 9.9 clear ip arp inspection statistics Description The clear ip arp inspection statistics command is - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 92
command. Syntax ip dos-prevent no ip dos-prevent Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DoS defend function globally: T1500G-10MPS(config)#ip dos-prevent 10.2 ip dos-prevent type - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 93
when attacked by syn-flood. win-nuke -- winNuke attack. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DoS Defend Type named Land attack: T1500G-10MPS(config)#ip dos-prevent type land 80 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 94
/disable status, the DoS Defend Type, the count of the attack, etc. Syntax show ip dos-prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DoS information of the detected DoS attack globally: T1500G-10MPS(config)#show ip dos-prevent 81 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 95
log information saved in the switch. It has two output T1500G-10MPS(config)#logging buffer 11.2 logging buffer level Description The logging buffer level command is used to configure the severity level and the status of the configuration input to the log buffer. To return to the default configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 96
. By default, it is 6 indicating that the log information with level 0-6 will be saved in the log buffer. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Set the severity level as 5: T1500G-10MPS(config)#logging - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 97
flash, ranging from 1 to 48 hours. By default, the synchronization process takes place every 24 hours. Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify the log file synchronization frequency as 10 hours: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 98
value will be stored to the flash. To restore to the default level, please use no logging file flash level command. Syntax T1500G-10MPS(config)#logging file flash level 7 11.6 logging host index Description The logging host index command is used to configure the Log Host. To clear the configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 99
of the log host. The switch supports 4 log hosts at most. host-ip -- The IP for the log host. level Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable log host 2 and set its IP address as 192.168.0.148, the level 5: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 100
default, it is 5 indicating that all the log information between level 0-5 will be output to the terminal devices. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Set the severity level as 7: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 101
. Clear the information of the two channels, by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Clear the information in the log file: T1500G-10MPS(config)# clear logging buffer 11.10 show logging local - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 102
be displayed, ranging from 1 to 4. Display the configuration of all the log hosts by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the log host 2: T1500G-10MPS(config)# show logging loghost 2 11.12 show logging - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 103
level will display. Display all the log information in the log file by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the log information with the level marked 0~3 in the log file: T1500G-10MPS(config)# show logging flash level 3 90 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 104
use no ip ssh server command. Syntax ip ssh server no ip ssh server Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the SSH function: T1500G-10MPS(config)# ip ssh server 12.2 ip ssh version - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 105
, Operator and Power User level users have access to these commands. Example Enable SSH v2: T1500G-10MPS(config)# ip ssh version v2 12.3 ip ssh algorithm Description The ip ssh algorithm command is used to configure the algorithm in SSH function. To disable the specified algorithm, please use no - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 106
time of SSH as 30 seconds: T1500G-10MPS(config)# ip ssh timeout 30 12.5 ip ssh max-client Description The ip ssh max-client command is used to specify the maximum number of the connections to the SSH server. To return to the default configuration, please use no ip ssh max-client command. Syntax - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 107
::1234. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Download an SSH-1 type key file named ssh-key from TFTP server with the IP address 192.168.0.148: T1500G-10MPS(config)# ip ssh download v1 ssh - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 108
users have access to these commands. Example Remove the SSH-1 type public key from the switch: T1500G-10MPS# remove public-key v1 12.8 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH. Syntax show ip ssh Command Mode Privileged EXEC Mode and Any - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 109
Example Display the global configuration of SSH: T1500G-10MPS(config)# show ip ssh 96 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 110
is to provide an access control for LAN ports via the authentication. An 802.1X system include is usually an 802.1X-supported network device, such as this TP-LINK switch. It acts as an no dot1x system-auth-control Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 111
between the TP-LINK 802.1x supplicant and the switch. Please disable the handshake feature if you are using a non-TP-LINK 802.1x-compliant client software. This feature is enabled by default. Syntax dot1x handshake no dot1x handshake Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 112
uses extensible authentication protocol (EAP) to exchange information between the switch and the client. The EAP protocol packets with authentication data are access to these commands. Example Configure the Authentication Method of IEEE 802.1X as "pap": T1500G-10MPS(config)#dot1x auth-method pap 13 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 113
in the Guest VLAN can access the specified network sources. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Guest VLAN function for VLAN 5: T1500G-10MPS(config)#dot1x guest-vlan 5 100 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 114
quiet-period function and set the quiet-period as 5 seconds: T1500G-10MPS(config)#dot1x quiet-period 5 13.7 dot1x timeout Description The dot1x timeout command is used to configure the supplicant timeout. To restore to the default, please use no dot1x timeout supplicant-timeout command. Syntax dot1x - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 115
from 1 to 9 in second. By default, it is 3 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the supplicant's timeout value as 5 seconds: T1500G-10MPS(config)#dot1x timeout supplicant - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 116
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IEEE 802.1X function for the Gigabit Ethernet port 1/0/1: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 117
function for Gigabit Ethernet port 1/0/2: T1500G-10MPS(config)#interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)#dot1x guest-vlan 13.11 dot1x port-control Description The dot1x port-control command is used to configure the Control Mode of IEEE 802.1X for the specified port. By default, the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 118
to these commands. Example Configure the Control Mode for Gigabit Ethernet port 1/0/20 as "authorized-force": T1500G-10MPS(config)#interface gigabitEthernet 1/0/20 T1500G-10MPS(config-if)#dot1x port-control authorized-force 13.12 dot1x port-method Description The dot1x port-method command is used - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 119
and Power User level users have access to these commands. Example Configure the Control Type for Gigabit Ethernet port 1/0/20 as "port-based": T1500G-10MPS(config)#interface gigabitEthernet 1/0/20 T1500G-10MPS(config-if)#dot1x port-method port-based 13.13 show dot1x global Description The show dot1x - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 120
Privilege Requirement None. Example Display the configuration information of 802.1X for Gigabit Ethernet port 1/0/2: T1500G-10MPS(config)#show dot1x interface gigabitEthernet 1/0/2 Display the configuration information of 802.1X for all Ethernet ports: T1500G-10MPS(config)#show dot1x interface 107 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 121
entry. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a static Mac address entry to bind the MAC address 00:02:58:4f:6c:23, VLAN1 and port 1 together: T1500G-10MPS(config)# mac address-table - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 122
default. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the aging time as 500 seconds: T1500G-10MPS be added or removed manually, independent of the aging time. Syntax mac address-table filtering - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 123
T1500G-10MPS(config)# mac address-table filtering 00:1e:4b:04:01:5d vid 1 14.4 mac address-table notification Description The mac address-table notification command is used to configure management system (NMS) when the threshold of the switch's MAC address table is reached or exceeded. interval - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 124
as 2 seconds: T1500G-10MPS(config)# mac address-table notification global-status enable table-full-status enable interval 2 14.5 mac address-table notification (interface) Description The mac address-table notification command is used to configure the MAC change notification on port. Syntax mac - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 125
T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# mac address-table notification learn-mode-change enable 14.6 mac address-table max-mac-count Description The mac address-table max-mac-count command is used to configure the Port Security. To return to the default - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 126
aging time and can only be deleted manually too. However, the learned entries will be saved even the switch is rebooted. status -- Select the action to be taken when the number of the MAC addresses reaches the maximum learning number on the port. By default this function is disabled. • forward: The - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 127
Admin, Operator and Power User level users have access to these commands. Example Configure the max learned MAC address number is VLAN 2 as 1000, and drop the packets that have no match in the MAC address table: T1500G-10MPS(config)# mac address-table security vid 2 max-learn 1000 drop 14.8 show mac - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 128
filtering -- The type of your desired entry. By default all the entries are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all address entries: T1500G-10MPS(config)# show mac address-table 14.9 clear mac address - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 129
Displays the security information of all the Ethernet ports. port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the security configuration of all ports: T1500G-10MPS(config)# show mac address-table max-mac-count - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 130
. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the address configuration of port 1/0/1: T1500G-10MPS(config)# show mac address-table interface gigabitEthernet 1/0/1 14.13 show mac address-table count Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 131
The Ethernet port number. lagid -- The ID of the LAG. vlan-id -- Specify the VLAN which the entry belongs to. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of the MAC address 00:00:00:00:23:00 in VLAN 1: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 132
the MAC address configuration of vlan 1: T1500G-10MPS(config)# show mac address-table vlan 1 14.16 show mac address-table notification Description The show mac address-table notification command is used to display the MAC notificaiton configuration globally or on the specified port. Syntax show mac - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 133
mac address-table security [ vid vid ] Parameter vid --The specified VLAN id. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MAC address security configuration of vlan 1: T1500G-10MPS(config)# show mac address-table security vid 1 120 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 134
the time is 12/20/2010 17:30:35 T1500G-10MPS(config)# system-time manual 12/20/2010-17:30:35 15.2 system-time ntp Description The system-time ntp command is used to configure the time zone and the IP address for the NTP Server. The switch will get UTC automatically if it has connected - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 135
:30 -- TimeZone for Tehran. UTC+04:00 -- TimeZone for Moscow, St.Petersburg, Volgograd, Tbilisi, Port Louis. UTC+04:30 -- TimeZone for Kabul. UTC+05:00 -- TimeZone for Islamabad, Karachi, Tashkent :00 -- TimeZone for Nuku'alofa, Samoa. ntp-server -- The IP address for the Primary NTP Server. 122 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 136
Configure the system time mode as NTP, the time zone is UTC-12:00, the primary NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163, the fetching-rate is 11 hours: T1500G-10MPS Australia, Europe and New-Zealand respectively. The default value is Europe. Following are the time - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 137
the daylight saving time as USA standard: T1500G-10MPS(config)#system-time dst predefined USA 15.4 system-time dst date Description The system-time dst date command is used to configure the one-off daylight saving time. The start date is in the current year by default. The time range of the daylight - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 138
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the daylight saving time from zero clock, Apr 1st to zero clock Oct 1st and the offset is 30 minutes in 2015: T1500G-10MPS(config)# system-time dst date Apr 1 00:00 2015 Oct 1 00:00 2015 30 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 139
no hostname Parameter hostname -- System Name. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example "T1500G-10MPS". Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 140
default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the system location as SHENZHEN: T1500G-10MPS characters at most. It is "www.tp-link.com" by default. Command Mode Global Configuration Mode 127 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 141
contact information as www.tp-link.com: T1500G-10MPS(config)# contact-info www.tp-link.com 15.9 ip address Description This ip address command is used to configure the IP address and IP subnet mask for the specified interface manually. The interface type includes: routed port, port-channel interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 142
interface to obtain IP address from the BOOTP Server. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Client function on the Lay 3 routed port 1/0/1: T1500G-10MPS(config)# interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 143
, all configuration of the switch will restore to the factory defaults and your current settings will be lost. Syntax reset Command Mode Privileged EXEC Mode Privilege Requirement Only Admin level users have access to these commands. Example Reset the software of the switch: T1500G-10MPS# reset - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 144
settings: T1500G-10MPS# copy running-config startup-config 15.14 copy startup-config tftp Description The copy startup-config tftp command is used to backup the configuration file to TFTP server. Syntax copy startup-config tftp ip-address ip-addr filename name Parameter ip-addr -- IP Address of - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 145
to the switch from TFTP server with the IP 192.168.0.148: T1500G-10MPS# copy tftp startup-config ip-address 192.168.0.148 filename config Download the configuration file named as config.cfg to the switch from TFTP server with the IP fe80::1234 T1500G-10MPS# copy tftp startup-config ip-address fe80 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 146
no boot application Parameter image1 | image2 -- Specify the image file to be configured. By default, the image1.bin is the startup image and the image2.bin is the access to these commands. Example Configure the image2.bin as the startup image: T1500G-10MPS(config)# boot application filename image2 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 147
to these commands. Example Upgrade the switch's backup iamge file with the file firmware.bin in the TFTP server with the IP address 192.168.0.148, and reboot the switch with this firmware: T1500G-10MPS# firmware upgrade ip-address 192.168.0.148 filename firmware.bin It will only upgrade the backup - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 148
T1500G-10MPS# firmware upgrade ip-address fe80::1234 filename firmware.bin It will only upgrade the backup image. Continue? (Y/N):y Operation OK! Reboot with the backup image? (Y/N): n 15.19 ping Description The ping command is used to test the connectivity between the switch and one node of the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 149
commands. Example Test the connectivity between the switch and the network device with the IP 192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: T1500G-10MPS# tracert 192.168.0.131 20 136 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 150
, Device Location, System Contact, Hardware Version, Firmware Version, System Time, Run Time and so on. Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the system information: T1500G-10MPS# show system-info 15.22 show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 151
commands. Example Display the system boot configuration information: T1500G-10MPS# show boot 15.24 show running-config Description The show running-config command is used to display the current operating configuration of the system or of a specified port. Syntax show running-config Command Mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 152
Example Display the system current operating configuration: T1500G-10MPS# show running-config 15.25 show startup-config Description The show startup-config command is used to display the current configuration saved in the switch. These configuration settings will not be lost the next time you reboot - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 153
-time dst command is used to display the DST information of the switch. Syntax show system-time dst Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DST information of the switch T1500G-10MPS# show system-time dst 15.28 show system-time ntp - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 154
is selected for Cable test. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Show the cable-diagnostics of port 3: T1500G-10MPS# show cable-diagnostics interface gigabitEthernet 1/0/3 15.30 show cpu-utilization Description The show cpu-utilization - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 155
system's memory utilization in the last 5 seconds/1minute/5minutes. Syntax show memory-utilization Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the memory utilization information of the switch: T1500G-10MPS# show memory-utilization 142 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 156
Mode and configure port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 16.2 interface range gigabitEthernet Description The interface range gigabitEthernet command is used to enter the interface range gigabitEthernet Configuration Mode and configure multiple Gigabit Ethernet ports at - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 157
results in an error on one port. Example To enter the Interface range gigabitEthernet Configuration Mode, and configure ports 1, 2, 3, 6, 7 and 9 at the same time by adding them to one port-list: T1500G-10MPS(config)# interface range gigabitEthernet 1/0/1-3,1/0/6-7,1/0/9 16.3 description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 158
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Disable port 1/0/3: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 159
the flow-control function for port 1/0/3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# flow-control 16.6 duplex Description The duplex command is used to configure the Duplex Mode for an Ethernet port. To return to the default configuration, please use no duplex - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 160
jumbo frame which is allowed to pass through the switch as 1600 bytes: T1500G-10MPS(config)# jumbo-size 1600 16.8 speed Description The speed command is used to configure the Speed Mode for an Ethernet port. To return to the default configuration, please use no speed command. Syntax speed { 10 | 100 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 161
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the Speed Mode as 100Mbps for port 1/0/3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# speed 100 16.9 storm-control Description The storm-control command is - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 162
and Power User level users have access to these commands. Example Configure the ingress-rate as 5120Kbps and egress-rate as 1024Kbps for port 1/0/5: T1500G-10MPS(config)# interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)# bandwidth ingress 5120 egress 1024 16.11 clear counters Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 163
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the connection status of all ports and LAGs: T1500G-10MPS(config)# show interface status Display the connection status of port 1/0/1: T1500G-10MPS(config)# show interface status gigabitEthernet 1/0/1 150 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 164
the statistics information of port 1/0/2: T1500G-10MPS(config)# show interface counters gigabitEthernet 1/0/2 16.14 show interface configuration Description The show interface configuration command is used to display the configurations of all ports and LAGs, including Port-status, Flow Control - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 165
Privilege Requirement None. Example Display the configurations of all Ethernet ports and LAGs: T1500G-10MPS(config)# show interface configuration Display the configurations of port 1/0/2: T1500G-10MPS(config)# show interface configuration gigabitEthernet 1/0/2 16.15 show storm-control Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 166
port-list ] [ port-channel lagid-list ] Parameter port-list --The list of Ethernet ports. lagid-list -- The list of LAGs. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bandwidth-limit information of port 1/0/4: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 167
service experience of a better quality. 17.1 qos Description The qos command is used to configure the priority level of packets from the port. To return to the default configuration Configure the priority of port 1/0/5 as TC3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/5 T1500G-10MPS( - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 168
egress queue: T1500G-10MPS (config)# qos cos 17.3 qos dscp Description The qos dscp command is used to enable the mapping relation between DSCP Priority and CoS value. To disable the mapping relation, please use no qos dscp command. Syntax qos dscp no qos dscp Command Mode Global Configuration Mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 169
Priority and CoS value: T1500G-10MPS(config)# qos dscp 17.4 qos queue cos-map Description The qos queue cos-map command is used to configure the mapping relation between IEEE 802.1P priority tag/IEEE 802.1Q tag, CoS value and the TC egress queue. To return to the default configuration, please use no - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 170
T1500G-10MPS(config)# qos queue cos-map 5 2 17.5 qos queue dscp-map Description The qos queue dscp-map command is used to configure the mapping relation between DSCP Priority and the TC queue. To return to the default configuration the untagged non-IP datagram are mapped based on port priority mode. - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 171
T1500G-10MPS(config)# qos queue dscp-map 10-12 2 17.6 qos queue mode Description The qos queue mode command is used to configure the Schedule Mode. To return to the default -Priority + Weight Round Robin Mode. In this mode, the switch provides two scheduling groups, SP group and WRR group. Queues - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 172
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of QoS for all ports and LAGs: T1500G-10MPS# show qos interface Display the configuration of QoS for ports 1/0/1-4: T1500G-10MPS# show qos interface gigabitEthernet 1/0/1-4 17.8 show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 173
of DSCP Priority. Syntax show qos dscp-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of DSCP Priority: T1500G-10MPS# show qos dscp-map 17.10 show qos queue mode Description The show qos queue mode command is - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 174
is used to display the status of IEEE 802.1P priority and DSCP priority. Syntax show qos status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the status of IEEE 802.1P priority and DSCP priority: T1500G-10MPS# show qos status 161 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 175
specified as 1. port -- The monitoring port number. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Create monitor session 1 and configure port 1/0/1 as the monitoring port: T1500G-10MPS(config)# monitor session - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 176
1/0/2 Delete the monitor session 1: T1500G-10MPS(config)# no monitor session 1 18.2 monitor session source interface Description The monitor session source interface command is used to configure the monitored port/ LAG. To delete the corresponding monitored port, please use no monitor session - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 177
or not is not demanded strictly. 4. The monitoring port cannot be link-aggregation member. Example Create monitor session 1, then configure port 4, 5, 7 as monitored port and enable ingress monitoring: T1500G-10MPS(config)# monitor session 1 source interface gigabitEthernet 1/0/4-5,1/0/7 rx Delete - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 178
list of port 1/0/5: T1500G-10MPS(config)# interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)# port isolation gi-forward-list 1/0/1-2,1/0/4 po-forward-list 2 Set all Ethernet ports and LAGs to forward list of port 1/0/2, namely restore to the default setting: T1500G-10MPS(config)# interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 179
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the forward-list of port 1/0/2: T1500G-10MPS# show port isolation interface gigabitEthernet 1/0/2 Display the forward-list of all Ethernet ports and LAGs: T1500G-10MPS# show port isolation interface 166 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 180
Enable the loopback detection function globally: T1500G-10MPS(config)# loopback-detection 20.2 loopback-detection interval Description The loopback-detection interval command is used to define the interval of sending loopback detection packets from switch ports to network, aiming at detecting - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 181
1 to 100 and the default value is 3. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the recovery-time as 3 times of detection interval: T1500G-10MPS(config)# loopback-detection recovery - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 182
(config)# interface range gigabitEthernet 1/0/1-3 T1500G-10MPS(Config-if-range)# loopback-detection 20.5 loopback-detection config Description The loopback-detection config command is used to configure the process-mode and recovery-mode for the ports/LAGs by which the switch copes with the detected - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 183
, Operator and Power User level users have access to these commands. Example Configure the loopback detection process-mode as port-based and recovery-mode as manual for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# loopback-detection config process-mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 184
detection function: T1500G-10MPS# show loopback-detection global 20.8 show loopback-detection interface Description The show loopback-detection interface command is used to display the configuration of loopback detection function and the status of the specified Ethernet port/LAG. Syntax show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 185
Example Display the configuration of loopback detection function and the status of all ports and LAGs: T1500G-10MPS# show loopback-detection interface Display the configuration of loopback detection function and the status of port 1/0/5: T1500G-10MPS# show loopback-detection interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 186
ranges is 500-1499 and the Extend-IP ACL is 1500-2499. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a standard-IP ACL whose ID is 523: T1500G-10MPS(config)# access-list create 523 21.2 mac - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 187
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a MAC ACL whose ID is 23: T1500G-10MPS(config)# mac access-list 23 21.3 access-list standard Description The access-list standard command is used to add Standard-IP - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 188
add Rule 10 for it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, and the packets match this rule will be forwarded by the switch: T1500G-10MPS(config)# access-list create 520 T1500G-10MPS(config)# access-list standard 520 rule 10 permit sip 192 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 189
match this rule will be forwarded by the switch: T1500G-10MPS(config)# access-list create 2220 T1500G-10MPS(config)# access-list extended 2220 rule 10 permit sip 192.168.0.100 smask 255.255.255.0 21.5 rule Description The rule command is used to configure MAC ACL rule. To delete the corresponding - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 190
this rule will be forwarded by the switch: T1500G-10MPS(config)# mac access-list 20 T1500G-10MPS(config-mac-acl)# rule 10 permit Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a Policy named policy1: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 191
to which the above policy is applied. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add ACL whose ID is 120 for policy1: T1500G-10MPS(config)# access-list policy action policy1 120 21.8 access-list - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 192
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind ACL 100 to port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# access-list bind acl 100 21.9 access-list bind acl(vlan) Description The access-list bind acl - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 193
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind policy1 to port 1/0/2: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 194
acl-id -- The ID of the ACL selected to display the configuration. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the MAC ACL whose ID is 20: T1500G-10MPS(config)# show access-list 20 21.13 show access-list policy - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 195
show access-list bind command is used to display the configuration of Policy bind. Syntax show access-list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of Policy bind: T1500G-10MPS(config)# show access-list bind 182 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 196
these commands. Example Configure the max power the PoE switch can supply as 100W: T1500G-10MPS(config)# power inline PoE profile for the switch. To delete the configured PoE profile configuration, please use no power profile command. PoE Profile is a short cut for the configuration of the PoE port - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 197
30w. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a PoE profile named "IP Camera" whose PoE status is "enable", PoE priority is "low" and the power limit is "5w": T1500G-10MPS(config)# power - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 198
, ranging from 1 to 16 characters. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a PoE time-range named "tRange1" for the switch: T1500G-10MPS(config)# power time-range tRange1 22.4 absolute - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 199
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an absolute mode time-range for the PoE of the switch and specify the date extending from 08:00 on May 5th, 2012 to 22:00 on Oct. 5th, 2012: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 200
access to these commands. Example Configure the Time-range named "tRange2" with two periodic time-ranges: one is from 08:00 to 18:00 during Monday to Friday, the other is from 10:00 to 16:00 during the weekends: T1500G-10MPS(config)# power time-range tRange2 T1500G-10MPS(config-time-range)# periodic - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 201
a PoE holiday named "LaborDay", and configure the start date as October 1st and the end date as October 3rd: T1500G-10MPS(config)# power holiday LaborDay start-date 05/01 end-date 05/03 22.7 holiday Description The holiday command is used to configure holiday mode for the Time-range of the switch - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 202
of the switch excludes the PoE holiday: T1500G-10MPS(config)# power time-range tRange3 T1500G-10MPS(config-time-range)# holiday exclude 22.8 power inline consumption (interface) Description The power inline consumption command is used to configure the power limit the corresponding port can supply - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 203
PD linked to the port with lower priority will be disconnected. By default, the priority level is "low". Command Mode Interface Configuration Mode commands. Example Configure the PoE priority as "low" for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 204
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the PoE feature for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 205
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind the PoE profile named "IP Camera" to port 1/0/2: T1500G-10MPS(config)# interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 206
of the certain port. Syntax show power inline configuration interface [ gigabitEthernet port ] Parameter port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the PoE configuration of all ports: T1500G-10MPS# show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 207
power inline information interface [ gigabitEthernet port ] Parameter port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the PoE information of all ports: T1500G-10MPS# show power inline information interface 22 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 208
show power holiday command is used to display the defined PoE holiday. Syntax show power holiday Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the defined PoE holiday: T1500G-10MPS# show power holiday 22.18 show power time-range Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 209
Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths. 23.1 debug spanning-tree Description The debug spanning-tree command is used to enable debuggning of spanning-tree - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 210
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the STP function: T1500G-10MPS(config)# spanning-tree 23.3 spanning-tree(interface) Description The spanning-tree command is used to enable STP function for a port - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 211
1/0/2 T1500G-10MPS(config-if)# spanning-tree 23.4 spanning-tree common-config Description The spanning-tree common-config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances. To return to the default configuration, please - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 212
1/0/1 T1500G-10MPS(config-if)# spanning-tree common-config port-priority 64 ext-cost 100 int-cost 100 portfast enable point-to-point open 23.5 spanning-tree mode Description The spanning-tree mode command is used to configure the STP mode of the switch. To return to the default configurations - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 213
default value. rstp --Rapid Spanning Tree Protocol mstp --Multiple Spanning Tree Protocol Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the spanning-tree mode as mstp: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 214
namely remove all the mapping VLANs 1-100: T1500G-10MPS(config)# spanning-tree mst configuration T1500G-10MPS(config-mst)# no instance 1 Remove VLANs 1-50 in mapping VLANs 1-100 for Instance 1: T1500G-10MPS(config)# spanning-tree mst configuration T1500G-10MPS(config-mst)# no instance 1 vlan 1-50 23 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 215
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the region name of MST as "region1": T1500G-10MPS(config)# spanning-tree mst configuration T1500G-10MPS(config-mst)# name region1 23.9 revision Description The revision command is used to - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 216
its priority as 4096: T1500G-10MPS(config)# spanning-tree mst instance 1 priority 4096 23.11 spanning-tree mst Description The spanning-tree mst command is used to configure MST Instance Port. To return to the default configuration of the corresponding Instance Port, please use no spanning-tree - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 217
cost as 2000: T1500G-10MPS(config)# interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)# spanning-tree mst instance 1 port-priority 64 cost 2000 23.12 spanning-tree priority Description The spanning-tree priority command is used to configure the bridge priority. To return to the default value of - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 218
the bridge priority as 4096: T1500G-10MPS(config)# spanning-tree priority 4096 23.13 spanning-tree timer Description The spanning-tree timer command is used to configure forward-time, hello-time and max-age of Spanning Tree. To return to the default configurations, please use no spanning-tree - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 219
, ranging from 1 to 20 in pps. By default, it is 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the hold-count of STP as 8pps: T1500G-10MPS(config)# spanning-tree hold-count 8 23.15 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 220
discarded, ranging from 1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max-hops of STP as 30: T1500G-10MPS(config)# spanning-tree max-hops 30 23.16 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 221
1/0/2 T1500G-10MPS(config-if)# spanning-tree bpduguard 23.18 spanning-tree guard loop Description The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 222
Enable the Loop Protect function for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# spanning-tree guard loop Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 223
for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# spanning-tree guard tc 23.21 spanning-tree mcheck Description The spanning-tree mcheck command is used to enable mcheck. Syntax spanning-tree mcheck Command Mode Interface Configuration Mode (interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 224
commands. Example Enable mcheck for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# spanning-tree mcheck 23 Mode and Any Configuration Mode Privilege Requirement None. Example Display the active information of spanning-tree: T1500G-10MPS(config)# show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 225
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the spanning-tree information of all ports: T1500G-10MPS(config)# show spanning-tree interface Display the spanning-tree information of port 1/0/2: T1500G-10MPS(config)# show spanning-tree interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 226
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the protect information of all ports: T1500G-10MPS(config)# show spanning-tree interface-security Display the protect information of port 1: T1500G-10MPS(config)# show spanning-tree interface-security - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 227
of VLAN and MST Instance: T1500G-10MPS(config)#show spanning-tree mst configuration Display the related information of MST Instance 1: T1500G-10MPS(config)#show spanning-tree mst instance 1 Display all the ports information of MST Instance 1: T1500G-10MPS(config)#show spanning-tree mst instance - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 228
use no ip igmp snooping command. Syntax ip igmp snooping no ip igmp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IGMP Snooping function: T1500G-10MPS(config)# ip igmp snooping - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 229
600. The default aging time is 300 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify IGMP Snooping router port aging time as 100 seconds globally: T1500G-10MPS(config)# ip igmp snooping - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 230
600. The default aging time is 260 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify IGMP Snooping member port aging time as 100 seconds globally: T1500G-10MPS(config)# ip igmp snooping - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 231
. Example Enable the IGMP report suppression function: T1500G-10MPS(config)# ip igmp snooping report-suppression 24.6 ip igmp snooping immediate-leave Description The ip igmp snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the Fast Leave function - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 232
, ranging from 1 to 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the interval of Specific Query Message to 3 seconds: T1500G-10MPS(config)# ip igmp snooping last-listener query-inteval - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 233
sent, ranging from 1 to 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the number of Specific Query Message to 3: T1500G-10MPS(config)# ip igmp snooping last-listener query-count 3 24.10 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 234
1-3 rtime 300 T1500G-10MPS(config)# ip igmp snooping vlan-config 1-3 mtime 200 T1500G-10MPS(config)# ip igmp snooping vlan-config 1-2 rport interface gigabitEthernet 1/0/1 Add static multicast IP address 225.0.0.1, which corresponds to VLAN 2, and configure the forward ports as ports 1/0/1-3: 221 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 235
will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1 : T1500G-10MPS(config)# ip igmp snooping vlan-config 1 router - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 236
it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used. port-list -- The list of Ethernet ports. lagid -- The ID of the LAGs. Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 237
routers to these port-channels will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in multicast VLAN 2 : T1500G-10MPS(config)# ip igmp snooping multi - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 238
of the IGMP packets. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Replace the source IP address of the IGMP packets in multicast VLAN 2 as 192.168.0.112: T1500G-10MPS(config)# ip igmp snooping multi-vlan-config 2 replace - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 239
T1500G-10MPS(config)#ip igmp snooping querier vlan 1 24.16 ip igmp snooping querier vlan (general query) Description The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a general query frame. To return to the default configuration, please - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 240
vlan 2 query-interval 200 T1500G-10MPS(config)#ip igmp snooping querier vlan 2 max-response-time 20 24.17 ip igmp snooping max-groups Description The ip igmp snooping max-groups command is used to configure the maximum number of groups that a port can join in. The ip igmp snooping max-groups action - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 241
the maximum numbers of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace: T1500G-10MPS(config)#interface range gigabitEthernet 1/0/2-5 T1500G-10MPS(config-if-range)#ip igmp snooping max-groups 10 T1500G-10MPS(config-if-range)#ip igmp snooping max-groups action - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 242
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the filtering mode of profile 1 as deny: T1500G-10MPS(config)# ip igmp profile 1 T1500G-10MPS(config-igmp-profile)#deny 24.20 permit Description The permit command is used to - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 243
access to these commands. Example Configure one of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1: T1500G-10MPS(config)# ip igmp profile 1 T1500G-10MPS(config-igmp-profile)#range 225.1.1.1 226.3.2.1 24.22 ip igmp filter Description The ip igmp filter command is used - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 244
1/0/2 T1500G-10MPS(config-if)# ip igmp filter 1 24.23 clear ip igmp snooping statistics Description The clear ip igmp snooping statistics command is used to clear the statistics of the IGMP packets. Syntax clear ip igmp snooping statistics Command Mode Privileged EXEC Mode and Any Configuration Mode - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 245
the global configuration of IGMP: T1500G-10MPS# show ip igmp snooping 24.25 show ip igmp snooping interface Description The show ip igmp snooping interface command is used to display the port configuration of IGMP snooping. Syntax show ip igmp snooping interface [ gigabitEthernet [ port | port-list - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 246
Example Display the IGMP baisic configuration configuration of all ports and LAGs: T1500G-10MPS# show ip igmp snooping interface basic-config Display the IGMP basic configuration of port 1/0/2: T1500G-10MPS# show ip igmp snooping interface gigabitEthernet 1/0/2 basic-config Display the IGMP packet - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 247
-vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the Multicast VLAN configuration: T1500G-10MPS# show ip igmp snooping multi-vlan 24.28 show ip igmp snooping groups vlan Description The show ip igmp snooping groups vlan command is used to - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 248
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all IGMP snooping groups: T1500G-10MPS#show ip igmp snooping groups Display all the multicast entries in VLAN 5: T1500G-10MPS(config)#show ip igmp snooping groups vlan 5 Display the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 249
Mode Privilege Requirement None. Example Display all Querier information: T1500G-10MPS(config)# show ip igmp snooping querier 24.31 show ip igmp profile Description The show ip igmp profile command is used to display the configuration information of all the profiles or a specific profile. Syntax - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 250
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of all profiles: T1500G-10MPS(config)# show ip igmp profile 237 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 251
. To return to the default configuration, please use no snmp-server command. Syntax snmp-server no snmp-server Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the SNMP function: T1500G-10MPS(config)# snmp-server 25 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 252
Only Admin level users have access to these commands. Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station: T1500G-10MPS(config)# snmp-server view view1 1.3.6.1.6.3.20 include 25.3 snmp-server group Description The snmp - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 253
, and configure the name as group 1, the Security Model as SNMP v3, the security level as authNoPriv, the management access to the assigned View viewDefault as read-write, besides the notification messages sent by View viewDefault can be received by Management station: T1500G-10MPS(config)# snmp - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 254
the switch via the port authentication is performed via HMAC-MD5 algorithm and SHA indicates the port default, the Authentication Mode is "none". confirm-pwd -- Authentication Password, ranging from 1 to 16 characters. The question marks and spaces are not allowed. This password in the configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 255
method is used. By default, the Privacy Mode is configure the Security Model of the user as v3, the Security Level of the group as authPriv, the Authentication Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 256
: T1500G-10MPS(config)# snmp-server community public read-write viewDefault 25.6 snmp-server host Description The snmp-server host command is used to add Notification. To delete the corresponding Notification, please use no snmp-server host command. Syntax snmp-server host ip udp-port user - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 257
time for the switch to wait as 1000 seconds, and the retries time as 100: T1500G-10MPS(config)# snmp-server host 192.168.0.146 162 admin smode v2c type inform retries 100 timeout 1000 Add a Notification entry, and configure the IP Address of the management Host as fe80::1234, the UDP port as 162 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 258
the local and remote are both not configured. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Specify the local engineID as 1234567890, and the remote engineID as abcdef123456: T1500G-10MPS(config)# snmp-server engineID local - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 259
. By default, it is enabled. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP standard linkup trap for the switch: T1500G-10MPS(config)# snmp-server traps snmp linkup 25.9 snmp-server traps link-status Description - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 260
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP link status trap for port 3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 261
It is sent when memory usage exceeds 80%. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP extended bandwidth-control trap for the switch: T1500G-10MPS(config)# snmp-server traps bandwidth-control 25.11 snmp-server - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 262
Enable VLAN-created trap only for the switch: T1500G-10MPS(config)# snmp-server traps vlan create 25.12 rmon history Description The rmon history command is used to configure the history sample entry. To return to the default configuration, please use no rmon history command. RMON (Remote Monitoring - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 263
T1500G-10MPS(config)# rmon history 1-3 interface gigabitEthernet 1/0/2 interval 100 owner owner1 25.13 rmon event Description The rmon event command is used to configure the entries of SNMP-RMON Event. To return to the default configuration, please use no rmon event command. Event Group, as one of - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 264
T1500G-10MPS(config)# rmon event 1-4 user user1 description description1 type log owner owner1 25.14 rmon alarm Description The rmon alarm command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no rmon alarm command. Alarm Group is one of the - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 265
. By default, it is 1800. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 266
of 1-3,5. port -- The statistics port number, in the format of 1/0/1. owner-name -- The creator of the event entry, ranging from 1 to 16 characters. By default, it is Configure the statistics entries 1-3 with the statistics port as 1/0/1, owner as owner1 and status as valid: T1500G-10MPS(config - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 267
View table. Syntax show snmp-server view Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the View table: T1500G-10MPS# show snmp-server view 25.18 show snmp-server group Description The show snmp - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 268
User table. Syntax show snmp-server user Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the User table: T1500G-10MPS# show snmp-server user 25.20 show snmp-server community Description The show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 269
the SNMP. Syntax show snmp-server engineID Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the engineID: T1500G-10MPS# show snmp-server engineID 25.23 show rmon history Description The show rmon - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 270
command. By default, the configuration of all SNMP-RMON enabled entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the Event configuration of entry1-4: T1500G-10MPS# show rmon - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 271
By default, the configuration of all Alarm Management entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the Alarm Management entry 1-2: T1500G-10MPS# show - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 272
Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the statistics entry 1: T1500G-10MPS#show rmon statistics 1 259 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 273
function globally: T1500G-10MPS(config)#lldp 26.2 lldp hold-multiplier Description The lldp hold-multiplier command is used to configure the Hold Hold Multiplier * Transmit Interval. To return to the default configuration, please use no lldp hold-multiplier command. Syntax lldp hold- - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 274
to these commands. Example Specify Hold Multiplier as 5: T1500G-10MPS(config)#lldp hold-multiplier 5 26.3 lldp timer Description The lldp timer command is used to configure the parameters about transmission. To return to the default configuration, please use no lldp timer command. Syntax lldp timer - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 275
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable Gigabit Ethernet port 1/0/1 to receive LLDPDU: T1500G-10MPS(config)#interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 276
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable Gigabit Ethernet port 1/0/1 to transmit LLDPDU: T1500G-10MPS(config)# interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 277
commands. Example Enable the SNMP notification for Gigabit Ethernet port 1/0/1: T1500G-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#lldp snmp-trap 26.7 lldp tlv-select Description The lldp tlv-select command is used to configure TLVs to be included in outgoing LLDPDU. To - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 278
Start Count parameter. It ranges from 1 to 10. By default, it is 4. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify Fast Start Count as 5: T1500G-10MPS(config)# lldp med-fast-count 5 26.9 lldp med-status - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 279
1/0/2 T1500G-10MPS(config-if)# lldp med-status 26.10 lldp med-tlv-select Description The lldp med-tlv-select command is used to configure LLDP-MED TLVs to be included in outgoing LLDPDU for the corresponding port. To exclude LLDP-MED TLVs, please use no lldp med-tlv-select command. By default, All - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 280
T1500G-10MPS(config-if)# no lldp med-tlv-select network-policy inventory- management 26.11 lldp med-location Description The lldp med-location command is used to configure the Location Identification TLV's content in outgoing LLDPDU of the port. Syntax lldp med-location { emergency-number identifier - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 281
show lldp interface [ gigabitEthernet port ] Parameters port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the LLDP configuration of Gigabit Ethernet port 1/0/1: T1500G-10MPS#show lldp interface gigabitEthernet - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 282
local-information interface [ gigabitEthernet port ] Parameters port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the LLDP information of Gigabit Ethernet port 1/0/1: T1500G-10MPS#show lldp local-information - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 283
traffic interface [ gigabitEthernet port ] Parameters port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the LLDP statistic information of Gigabit Ethernet port 1/0/1: T1500G-10MPS#show lldp traffic interface - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 284
switch supports Login List for users to gain access to the switch, and Enable List for normal users to gain administrative privileges. RADIUS/TACACS+ Server User can configure is disabled by default. Syntax aaa enable no aaa enable Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 285
Enable the AAA function globally: T1500G-10MPS(config)# aaa enable 27.2 default, it is empty. 7 -- Indicates a symmetric encrypted password with fixed length will follow. encrypted-password -- A symmetric encrypted password with fixed length, which you can copy from another switch's configuration - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 286
service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Set the elevation password as 123 for the current logged-in user to gain administrator level privileges: T1500G-10MPS switch. will follow. By default, the encryption type is - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 287
form: T1500G-10MPS (config)#enable admin secret 0 123 27.4 tacacas-server host Description The tacacs-server host command is used to configure a new TACACS+ server. To delete the specified TACACS+ server, please use no tacacs-server host command. Syntax tacacs-server host ip-address [ port port-id - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 288
are added in the server group "tacacs" by default. Example Configure a TACACS+ server with the IP address as 1.1.1.1, TCP port as 1500, timeout as 6 seconds, and the unencrypted key string as 12345. T1500G-10MPS(config)# tacacs-server host 1.1.1.1 port 1500 timeout 6 key 12345 27.5 show tacacs - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 289
T1500G-10MPS(config)# show tacacs-server 27.6 radius-server host Description The radius-server host command is used to configure a new RADIUS server. To delete the specified RADIUS server, please use no radius-server host command. Syntax radius-server host ip-address [ auth-port port-id ] [ acct- - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 290
server group "radius" by default. Example Configure a RADIUS server with the IP address as 1.1.1.1, authentication port as 1200, timeout as 6 seconds, retransmit times as 3, and the unencrypted key string as 12345. T1500G-10MPS(config)# radius-server host 1.1.1.1 auth-port 1200 timeout 6 retransmit - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 291
TACACS+/RADIUS servers for authentication. This command puts the switch in the server group subconfiguration mode. To delete the Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create a RADIUS server group with the name radius1: T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 292
the server's IP address. Command Mode Server Group Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create the RADIUS server 1.1.1.1 to RADIUS server group "radius1": T1500G-10MPS(config)# aaa group radius radius1 T1500G-10MPS(aaa-group)# server - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 293
these commands. User Guidelines By default the login authentication method list is "default" with "local" as method1. Example Configure a login authentication method list "list1" with the priority1 method as radius and priority2 method as local: T1500G-10MPS(config)# aaa authenticaiton login list1 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 294
these commands. User Guidelines By default the enable authentication method is "default" with "none" as method1. Example Configure a privilege authentication method list "list2" with the priority1 method as radius and priority2 method as local: T1500G-10MPS(config)# aaa authenticaiton enable list2 - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 295
RADIUS server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1X authentication method as "radius1": T1500G-10MPS(config)# aaa - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 296
server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1X accounting method as "radius1": T1500G-10MPS(config)# aaa accounting - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 297
to these commands. Example Display the information of the default 802.1X accounting method list: T1500G-10MPS(config)# show aaa accounting 27.17 line telnet Description The line telnet command is used to enter the Line Configuration Mode to configure the telnet terminal line to which you want to - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 298
by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the telnet terminal line as "list1": T1500G-10MPS(config)#line telnet T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 299
. It is "default" by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the ssh terminal line as "list1": T1500G-10MPS(config)# line ssh - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 300
by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the telnet terminal line as "list2": T1500G-10MPS(config)#line telnet T1500G-10MPS - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 301
. It is "default" by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the ssh terminal line as "list2": T1500G-10MPS(config)# line ssh - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 302
. It is "default" by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the HTTP access as "list2": T1500G-10MPS(config)# ip http enable - TP-Link T1500G-10MPS | T1500G-10MPSUN V1 CLI Reference Guide - Page 303
ssh and HTTP. Syntax show aaa global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the AAA function's global status and each application's method list: T1500G-10MPS(config)# show aaa global 290
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
 |
 |
CLI Guide
JetStream 8-Port Gigabit Smart PoE+ Switch
with 2 SFP Slots
T1500G-10MPS
REV1.0.0
1910011909