Toshiba 20AF43 User Manual - Page 12

Programming for Use with a VCR, DVD Player, or Cable TV Converter, Using the, Remote Control - menu without remote

Get Toshiba 20AF43 PDF manuals and user guides View all Toshiba 20AF43 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

To control a cable TV CABLE converter: Power Program the remote control to recognize the brand of your converter Channel (see "Programming the Numbers remote control for use with a VCR, DVD player, or cable TV converter" below). The buttons Channel +/- shown at right will control the cable TV converter. Press the CABLE button Enter first. POWER TV 12 VCR CABLE DVD 3 4 5 6  7890 CH + VOL Ð MENU/ ENTER VOL + CH Ð EXIT RECALL TV/VIDEO FAV DVD MENU CH RTN FAV RESET CAP/TEXT 1/2 16:9 DVD CLEAR TOP MENU DVD MENU CODE MTS SLEEP MUTE REW PLAY FF TV/VCR STOP PAUSE/STILL REC VCR CH DVD SKIP Using the Remote Control Programming the remote control for use with a VCR, DVD player, or cable TV converter This remote control is pre-programmed to operate Toshiba VCRs and DVD players. To control VCRs, DVD players, or cable converters other than Toshiba models, you must follow the steps below to program your remote control. 1. While holding down the CODE button, press the button for the device you want to control (VCR, DVD, or CABLE). 2. Enter the 2-digit code listed on page 13 using the Number buttons (0-9) within 10 seconds. 3. Point the remote control at the VCR, DVD player, or converter and press POWER to test the code. If the VCR, DVD player, or converter turns on, you have entered the right code. If the VCR, DVD player, or converter does not respond to the remote control, you may have entered the wrong code. Repeat steps 1-2 with another code. For future reference, write down the codes you used: VCR code DVD player code Cable TV converter code 12 POWER TV 12 VCR CABLE DVD 3 4 5 6  7890 CH + VCR CABLE DVD VOL Ð MENU/ ENTER VOL + CH Ð EXIT RECALL TV/VIDEO FAV DVD MENU CH RTN FAV RESET CAP/TEXT 1/2 16:9 DVD CLEAR TOP MENU DVD MENU CODE MTS SLEEP MUTE REW PLAY FF Code Notes: • When shipped from the factory, the remote control is set to operate your TV. • If you do not enter the code within 10 seconds from step 1 or if you enter a code not listed below, this operation is canceled. • Each time you replace the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch and does not respond to any of the codes for your VCR, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
12
Programming the remote control for use with
a VCR, DVD player, or cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs and
DVD players. To control VCRs, DVD players, or cable converters other
than Toshiba models, you must follow the steps below to program your
remote control.
1.
While holding down the CODE button, press the button for the
device you want to control (VCR, DVD, or CABLE).
2.
Enter the 2-digit code listed on page 13 using the Number buttons
(0-9) within 10 seconds.
3.
Point the remote control at the VCR, DVD player, or converter and
press POWER to test the code.
If the VCR, DVD player, or converter turns on, you have entered
the right code.
If the VCR, DVD player, or converter does not respond to the
remote control, you may have entered the wrong code. Repeat
steps 1-2 with another code.
For future reference, write down the codes you used:
VCR code
________________________
DVD player code ___________________
Cable TV converter code _____________
Notes:
•
When shipped from the factory, the remote
control is set to operate your TV.
•
If you do not enter the code within 10
seconds from step 1 or if you enter a code
not listed below, this operation is canceled.
•
Each time you replace the batteries, you
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does
not respond to any of the codes for your
VCR, set the switch to the other position
(VCR1 or VCR2) and reprogram the remote
control.
Using the
Remote Control
Code
To control a cable TV
converter:
Program the remote
control to recognize the
brand of your converter
(see “Programming the
remote control for use
with a VCR, DVD player,
or cable TV converter”
below). The buttons
shown at
right will control
the cable TV converter.
Press the CABLE button
first.
Power
Enter
CABLE
Channel
Numbers
Channel +/–
DVD
CABLE
VCR