Toshiba 50H12 Owners Manual - Page 15

Programming for Use with a non-Toshiba VCR or Cable TV Converter

Get Toshiba 50H12 PDF manuals and user guides View all Toshiba 50H12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Introduction Connecting your TV Using the Remote Control Programming the remote control for use with a non-Toshiba VCR or cable TV converter The TV remote control is pre-programmed to operate Toshiba VCRs and cable TV converters. To use the remote control to operate a non-Toshiba VCR or cable TV converter, follow the steps below to program the remote control. 1. Refer to the "VCR code table" or "Cable TV converter code table" on pages 16-17 to find the corresponding code for your VCR or cable TV converter brand. If more than one code is listed, try each one separately until you find the one that works. 2. If you are reprogramming the remote control to operate your: • VCR: Set the TV/CABLE/VCR switch on the remote control to VCR. • Cable TV converter: Set the TV/CABLE/VCR switch on the remote control to CABLE. 3. White holding down the RECALL button, press the Number buttons (0-9) to enter the three-digit code for your VCR or cable TV converter. 4. Point the remote control at the VCR or converter and press POWER to test the code. If the VCR responds, you have entered the correct code. If the VCR or converter does not respond, you may have entered the wrong code. Repeat steps 1-4 using another code. 5. Reset the TV/CABLE/VCR switch to TV to control the TV. For future reference, write down the code(s) you used: VCR code Cable TV converter code LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 123 CH 456 789 CH RTN VOL 100 0 ENT ADV/ POP CH RECALL POWER Channel yz Channel Number Enter FAVORITE EXIT PIC SIZE FAV MENU/ ENTER FAV C.CAPT ADV/ POP CH STOP SOURCE PLAY PIP REC TV/VCR REW FF Note: • Each timeSTyILLouLOrCeATpElaSWcAeP the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. Setting up your TV Using the TV's Features Appendix Index 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Introduction
Connecting
y
our TV
Using the
Remote Control
Setting up
y
our TV
Using the TV’s
F
eatures
Appendix
Index
15
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
PIC SIZE
EXIT
LIGHT
STOP SOURCE
ADV/
POP CH
ADV/
POP CH
FAV
FAV
PLAY PIP
REC
TV/VCR
REW
FF
STILL
LOCATE
SWAP
FAVORITE
MENU/
C.CAPT
ENTER
Programming the remote control for use with a
non-Toshiba VCR or cable TV converter
The TV remote control is pre-programmed to operate Toshiba VCRs
and cable TV converters. To use the remote control to operate a
non-Toshiba VCR or cable TV converter, follow the steps below to
program the remote control.
1.
Refer to the “VCR code table” or “Cable TV converter code
table” on pages 16–17 to find the corresponding code for your
VCR or cable TV converter brand.
If more than one code is listed, try each one separately until you
find the one that works.
2.
If you are reprogramming the remote control to operate your:
•
VCR:
Set the TV/CABLE/VCR switch on the remote
control to VCR.
•
Cable TV converter:
Set the TV/CABLE/VCR switch on the
remote control to CABLE.
3.
White holding down the RECALL button, press the Number
buttons (0–9) to enter the three-digit code for your VCR or cable
TV converter.
4.
Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR responds, you have entered the correct code.
If the VCR or converter does not respond, you may have entered
the wrong code. Repeat steps 1–4 using another code.
5.
Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code(s) you used:
VCR code _____________________
Cable TV converter code _____________________
Note:
•
Each time you replace the batteries, you
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.” If
your VCR has this kind of switch and does
not respond to any of the codes for your
VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
POWER
Channel
yz
Channel
Number
Enter
RECALL