Toshiba 50H12 Owners Manual - Page 21
Adding Channels to the TV's Memory, Programming Now-Please Wait appears.
View all Toshiba 50H12 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
Introduction Connecting your TV Using the Remote Control Adding channels to the TV's memory When you press Channel y or z, your TV will select only the channels stored in the TV's channel memory. Follow the steps below and on the next page to program all active channels into the TV's memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 22). If you use both ANT-1 and ANT-2 terminals, you must program channels for each input source. To program channels automatically: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z until TV/CABLE is highlighted. 3. Press x or • to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 1 2 2 3 3 4 4 5 5 6 6 7 SET UP 7 8 8 9 LANGUAGE ENGL I SH 9 10 CLOCK SET 00:00 10 11 ANT 1 / 2 ANT1 11 12 TV / CABLE TV / CABLE 12 13 CH PROGRAM 13 14 ADD / ERASE ADD 14 15 15 16 16 17 17 18 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 4. Press z to select CH PROGRAM. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 1 2 2 3 3 4 4 5 5 6 6 7 SET UP 7 8 8 9 LANGUAGE ENGL I SH 9 10 CLOCK SET 00:00 10 11 ANT 1 / 2 ANT1 11 12 TV / CABLE CABLE 12 13 CH PROGRAM 13 14 ADD / ERASE ADD 14 15 15 16 16 17 17 18 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 5. Press x or • to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory. While the TV is cycling through the channels, the message "Programming Now-Please Wait" appears. 6. When channel programming is complete, the message "Completed" appears. 7. Press Channel y or z to view the programmed channels. Note: To tune the TV to a channel not programmed in the channel memory, use the Channel Number buttons on the remote control. LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 123 CH 456 789 CH RTN VOL 100 0 ENT ADV/ POP CH PIC SIZE FAV MENU/ ENTER FAV Channel yz Channel Numbers MENU yzx • FAVORITE EXIT C.CAPT ADV/ POP CH STOP SOURCE PLAY PIP REC TV/VCR REW FF STILL LOCATE SWAP Setting up your TV Using the TV's Features Appendix Index 21