Toshiba M100 User Manual
Toshiba M100 Manual
 |
View all Toshiba M100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Toshiba M100 manual content summary:
- Toshiba M100 | User Manual - Page 1
TOSHIBA Portégé M100 Portable Personal Computer User's Manual - Toshiba M100 | User Manual - Page 2
is assumed, with respect to the use of the information contained herein. TOSHIBA Portégé M100 Portable Personal Computer User's Manual First edition July 2003 Disclaimer This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the - Toshiba M100 | User Manual - Page 3
Product Name : Portégé M100 Model number : PPM10 not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used - Toshiba M100 | User Manual - Page 4
Address: TOSHIBAAmericaInformationSystems,Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949)583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PPM10* conforms to the following Standards: Supplementary Information: "The product complies with the - Toshiba M100 | User Manual - Page 5
event of problems, you should contact your equipment supplier in the first instance. Network Compatibility Statement This product is designed to work with, ,004 Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for - Toshiba M100 | User Manual - Page 6
are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one to which you will connect the modem ❑ The registration number that is located on the device The FCC registration number of the modem will be found on - Toshiba M100 | User Manual - Page 7
changes necessary to maintain uninterrupted service. If problems arise If any of your problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA - Toshiba M100 | User Manual - Page 8
of your fax software before sending messages. Instructions for IC CS-03 certified equipment 1 The above conditions may not prevent degradation of service in some situations. Repairs to certified equipment electrician, as appropriate. 2 The user manual of analog equipment must contain the equipment's - Toshiba M100 | User Manual - Page 9
warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region - Toshiba M100 | User Manual - Page 10
to Telecom. ❑ In addition to satisfactory line conditions a modem can only work properly if: a/ it is compatible with the modem at the other end Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call - Toshiba M100 | User Manual - Page 11
the Telecom line connection before the power connection, and reconnect the power first. ❑ This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility. NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM - Toshiba M100 | User Manual - Page 12
of Telepermit labels subject to the general instructions on format, size and colour on the at all times as proof to purchasers and service personnel that the product is able to be is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted - Toshiba M100 | User Manual - Page 13
Description on Laser specification The optical drive such of Federal Regulations by the United States of America, Department of Health & Human Services, Food and Drug Administration. In other countries, the drive is certified to comply to the model. Manufacturer TOSHIBA TEAC Type SD-C2612 DW-224E - Toshiba M100 | User Manual - Page 14
- Toshiba M100 | User Manual - Page 15
Table of Contents Preface Manual contents xxiii Conventions xxiv Abbreviations xxiv Icons xxiv Keys xxiv Key operation xxv Display xxv Messages xxv General Precautions Stress injury xxvii Heat injury xxvii - Toshiba M100 | User Manual - Page 16
14 Secondary battery pack 2-15 Slim Select Bay HDD adaptor 2-16 Weight saver module 2-17 Chapter 3 Getting Started Setting up your work space 3-2 3-3 Lighting 3-4 Work habits 3-4 Opening the display 3-5 Connecting the AC adaptor 3-6 Turning on the power 3-8 Windows XP/2000 setup 3-9 - Toshiba M100 | User Manual - Page 17
4-17 LAN 4-18 LAN cable types 4-18 Connecting LAN cable 4-18 Disconnecting LAN cable 4-19 Using the microphone 4-20 Keyboard Typewriter keys 5-1 F1 ... F12 function keys 5-2 Soft keys: Fn key combinations 5-2 Emulating keys on enhanced keyboard 5-2 Hotkeys 5-4 Fn Sticky key 5-6 Windows - Toshiba M100 | User Manual - Page 18
off 6-13 Extending battery life 6-13 Replacing the battery pack 6-14 Removing the battery pack 6-14 Installing the battery pack 6-15 TOSHIBA Password Utility 6-16 User password 6-16 Supervisor password 6-17 Starting the computer by password 6-18 Power-up modes 6-18 Windows utilities 6-18 - Toshiba M100 | User Manual - Page 19
(IEEE1394 8-19 Precautions 8-19 Connecting 8-20 Disconnecting 8-20 Security lock 8-21 Chapter 9 Troubleshooting Problem solving process 9-1 Preliminary checklist 9-1 Analyzing the problem 9-2 Hardware and system checklist 9-3 System start-up 9-3 Self test 9-4 Power 9-4 Password 9-7 xix - Toshiba M100 | User Manual - Page 20
9-17 Sound system 9-17 USB 9-18 Modem 9-19 Standby/Hibernation 9-20 Memory expansion 9-21 LAN 9-21 Wireless LAN 9-21 Bluetooth 9-22 i.LINK (IEEE1394 9-22 Real Time Clock 9-23 TOSHIBA support 9-24 Before you call 9-24 Where to write 9-24 Appendixes Appendix A Specifications A-1 Appendix - Toshiba M100 | User Manual - Page 21
Appendix E V.90 ...E-1 Appendix F Wireless LAN F-1 Appendix G AC Power Cord and Connectors G-1 Appendix H Internal Modem Guide H-1 Appendix I Parts Numbers I-1 Glossary Index xxi - Toshiba M100 | User Manual - Page 22
xxii - Toshiba M100 | User Manual - Page 23
manual tells how to set up and begin using your TOSHIBA Portégé M100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting tips on safety and designing your work area. Chapter 4, Operating Basics, includes - Toshiba M100 | User Manual - Page 24
the computer's power resources and battery save modes and how to set a password. Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on - Toshiba M100 | User Manual - Page 25
face you see to the left. Display ABC Names of Windows® or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of - Toshiba M100 | User Manual - Page 26
User's Manual xxvi - Toshiba M100 | User Manual - Page 27
TOSHIBA Instruction Manual for Safety & Comfort. It contains information on prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard used for a long time, avoid direct contact with the metal plate supporting the I/O ports. It can become hot. ❑ The surface of the - Toshiba M100 | User Manual - Page 28
User's Manual PC card overheating Some product may vary from specifications under the following conditions: 1. use of certain peripheral products 2. use of battery power instead of AC Conditions" in your product Resource Guide. Contact TOSHIBA Service and Support for more information. xxviii - Toshiba M100 | User Manual - Page 29
INTRODUCTION Chapter 1 Introduction Equipment checklist 1-1 Hardware 1-1 Software 1-1 Features 1-3 Special features 1-9 Utilities 1-11 Options 1-12 - Toshiba M100 | User Manual - Page 30
INTRODUCTION - Toshiba M100 | User Manual - Page 31
❑ Modular cable ❑ One blue spare AccuPoint II (pointing device) cap ❑ Slim Select Bay weight saver module Software Windows XP Professional ❑ The following software is preinstalled: • Microsoft® Windows XP Professional • Modem driver • Display Drivers for Windows • TOSHIBAUtilities • Sound Driver - Toshiba M100 | User Manual - Page 32
Windows XP manual package • Instruction Manual for Safety & Comfort • End User License Agreement • International Limited Warranty (ILW) Instruction (This instruction is included only with computers sold in ILW supported areas.) ❑ Product Recovery CD-ROM contains Windows XP or 2000 and TOSHIBA - Toshiba M100 | User Manual - Page 33
Windows 2000 manual package • The same documentation that is supplied with Windows XP. If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA's advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS RAM The - Toshiba M100 | User Manual - Page 34
INTRODUCTION User's Manual Disks Built-in Hard disk • 40billionbytes(37 CD/DVDs without using an adaptor. It runs DVDROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. The drive supports the following formats: • DVD-ROM • DVD-Video • CD-ROM • CD-EXTRA • PhotoCD™ • Audio CD • CD-ROMXA - Toshiba M100 | User Manual - Page 35
Features Display The computer's LCD panel supports high-resolution video graphics. The screen can be set at a wide range of the keyboard and control buttons at the base of the keyboard enable control of the on-screen pointer and scrolling of windows. Power Battery pack RTC battery AC adaptor - Toshiba M100 | User Manual - Page 36
User's Manual Ports with IrDA 1.1 compatible external devices. 15-pin, analog VGA port supports VESA DDC2B compatible functions. Special port for connecting an optional this slot. Multimedia Sound System Windows Sound System compatible sound system provides internal speakers as well as jacks - Toshiba M100 | User Manual - Page 37
only in USA and Canada. Only V.90 is available in other regions. LAN The computer is equipped with a LAN card that supports Ethernet LAN (10 Mbit/s, 10BASE-T) and Fast Ethernet LAN (100 Mbit/s, 100BASE-TX). It is preinstalled as a standard device in some markets. Wireless LAN Some - Toshiba M100 | User Manual - Page 38
Manual Bluetooth Some computers in this series are equipped with Bluetooth functions. Bluetooth wireless technology eliminates the need for cables or secondary battery. The TOSHIBA Mobile Extension TOSHIBA Utilities Plug and Play One of the following operating systems are available Windows XP - Toshiba M100 | User Manual - Page 39
lettering make up the keypad overlay, which lets you use the keyboard for ten-key operations or cursor control. Display automatic power off in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver. Power on password Two levels of password security are available: - Toshiba M100 | User Manual - Page 40
's Manual Panel in the When I close the lid item of the System Power Mode window in TOSHIBA Power Saver. This feature lets you set a time and date for the 's main memory. When you turn on the power again, you can continue working right where you left off. This feature lets you turn off the power - Toshiba M100 | User Manual - Page 41
online manual, work in Windows. To start the utility, click the Windows Start button, point to All Programs, point to TOSHIBA Utilities and click Fn-esse. TOSHIBAPassword The TOSHIBA Password Utility provides two levels of Utility password security: User and Supervisor. Display Driver for Windows - Toshiba M100 | User Manual - Page 42
to allow easy control of communication device and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. You can boot TOSHIBA ConfigFree from the menu bar as follows. [Start] - [All - Toshiba M100 | User Manual - Page 43
port. (You cannot format 720-kilobyte diskettes on Windows XP, but you can use previously formatted disks.) Battery Charger The Battery Charger lets you charge extra batteries outside the computer. It must be used with the Battery Charge cable that is supplied only with the Slim Port Replicator - Toshiba M100 | User Manual - Page 44
INTRODUCTION User's Manual 1-14 - Toshiba M100 | User Manual - Page 45
side 2-4 Underside 2-5 Front with the display open 2-7 Indicators 2-9 AC adaptor 2-11 Slim Select Bay modules 2-12 DVD-ROMdrive 2-12 CD-RW/DVD-ROMdrive 2-14 Secondary battery pack 2-15 Slim Select Bay HDD adaptor 2-16 Weight saver module 2-17 - Toshiba M100 | User Manual - Page 46
THE GRAND TOUR - Toshiba M100 | User Manual - Page 47
THE GRAND TOUR Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer's front with its display panel in the closed position. - Toshiba M100 | User Manual - Page 48
Manual Left side Figure 2-2 shows the computer's left side. SECURITY LOCK SLOT DC IN 15V MICROPHONE HEADPHONE THE GRAND TOUR FAN VENT PC CARD SLOT INFRARED PORT VOLUME CONTROL Figure 2-2 The left side of the computer Security lock slot Fan vent A security cable The slot supports 16bit PC cards - Toshiba M100 | User Manual - Page 49
device for audio output. When you connect headphones, the internal speakers are automatically disabled. Use this dial to adjust the volume of the system speakers and headphones. Right side Figure 2-3 shows the computer's right side. BATTERY LOCK SD CARD INDICATOR SD CARD SLOT SLIM SELECT BAY - Toshiba M100 | User Manual - Page 50
User's Manual Back side Figure 2-4 shows the computer's back side. LAN ACTIVE INDICATOR ( equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions. CAUTIONS: 1. In case of a lightning - Toshiba M100 | User Manual - Page 51
enables data transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) CAUTION: Keep foreign objects out of the USB connectors. A pin or similar SELECT BAY HOLES LATCH DOCKING PORT BATTERY PACK HDD PACK COVER Figure 2-5 The underside of the computer 2-5 - Toshiba M100 | User Manual - Page 52
THE GRAND TOUR User's Manual Docking interface This port enables connection of an optional Power-Up Modes, describes how to access the battery pack. Additional battery packs can be purchased from your TOSHIBA dealer to extend the computer's battery operating time. Two screws secures the HDD cover. - Toshiba M100 | User Manual - Page 53
up. Position the display at a comfortable viewing angle. THE GRAND TOUR DISPLAY SCREEN DISPLAY HINGE POWER BUTTON STEREO SPEAKER (LEFT) TOSHIBA CONSOLE BUTTON TOSHIBA PRESENTATION BUTTON SENSOR SWITCH STEREO SPEAKER (RIGHIT) ACCUPOINT II MICROPHONE ACCUPOINT II CONTROL BUTTONS Figure 2-6 The - Toshiba M100 | User Manual - Page 54
mode returns to single display on LCD only. Setting of multi-monitor display in Windows XP, PC changes its display mode to the multimonitor display on LCD and CRT. is TOSHIBA Console. AccuPoint II A pointer control device located in the center of the keyboard is used to control the on-screen pointer - Toshiba M100 | User Manual - Page 55
you turn off the computer in Resume mode, this indicator blinks orange (one second on, two seconds off) while the computer shuts down. The Main battery indicator shows the condition of the charge. Green means fully charged and orange means being charged. Refer to Chapter 6, Power and Power-Up Modes - Toshiba M100 | User Manual - Page 56
Manual Slim Select Bay Orange Green No light Wireless communication The Slim Select Bay indicator glows in green when the computer is accessing a DVD-ROM drive, CD-RW/DVDROM drive, or Slim Select Bay HDD adaptor in the Slim Select Bay. When the secondary battery keyboard is in all-caps mode. 2-10 - Toshiba M100 | User Manual - Page 57
) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. You can use the keypad overlay (white labeled keys) for numeric input when to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 - Toshiba M100 | User Manual - Page 58
Manual THE GRAND TOUR Figure 2-10 The AC adaptor CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA , CDRW/DVD-ROM drive, optional secondary battery pack and optional Slim Select Bay HDD - Toshiba M100 | User Manual - Page 59
Slim Select Bay modules This drive supports the following formats: • DVDROM • CD-ROM • PhotoCD™ • CD-ROMXA • CD-I • CD the DVD/CD or the drive. DVD drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video media, make sure it matches - Toshiba M100 | User Manual - Page 60
THE GRAND TOUR User's Manual 5 Russia, Indian Subcontinent, Africa, North Korea 24speed(maximum) CD/DVD-IN-USE INDICATOR EJECT HOLE EJECT BUTTON Figure 2-12 The CD-RW/DVD-ROM drive This drive supports the following formats: • DVDROM • CD-ROM • PhotoCD™ • CD-ROMXA • CD-I • CD-R • DVDVideo • - Toshiba M100 | User Manual - Page 61
CD-RW/DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video media, make discs. Secondary battery pack An optional battery pack can be installed in the Slim Select Bay to increase the computer's battery power and operating - Toshiba M100 | User Manual - Page 62
User's Manual THE GRAND TOUR Figure 2-13 The secondary battery pack Slim Select Bay HDD adaptor You can increase your computer's data storage capacity by installing an optional integrated, 2 1/2" HDD in the Slim Select Bay. - Toshiba M100 | User Manual - Page 63
THE GRAND TOUR Slim Select Bay modules Weight saver module Installing a weight saver module in the Slim Select Bay lets you reduce the carrying weight of the computer. Figure 2-15 The weight saver module 2-17 - Toshiba M100 | User Manual - Page 64
THE GRAND TOUR User's Manual 2-18 - Toshiba M100 | User Manual - Page 65
space 3-2 General conditions 3-2 Placement of the computer 3-3 Seating and posture 3-3 Lighting 3-4 Work habits 3-4 Opening the display 3-5 Connecting the AC adaptor 3-6 Turning on the power 3-8 Windows XP/2000 setup 3-9 Turning off the power 3-9 Shut Down mode (Boot mode 3-9 Hibernation - Toshiba M100 | User Manual - Page 66
GETTING STARTED - Toshiba M100 | User Manual - Page 67
❑ Setting up your work space - for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability. ❑ Opening the display ❑ Connecting the AC adaptor ❑ Turning on the power ❑ Windows XP/2000 setup - Toshiba M100 | User Manual - Page 68
Manual Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work the computer near objects that create strong magnetic fields (e.g., stereo speakers). ❑ Some computers in the computer, including data storage media - Toshiba M100 | User Manual - Page 69
and distance as the computer. Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. BELOW EYE LEVEL GETTING STARTED FOOT REST 90O - Toshiba M100 | User Manual - Page 70
when you work. Do not slump forward or lean back too far. Lighting Proper lighting can improve legibility of the display and reduce eyestrain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate - Toshiba M100 | User Manual - Page 71
on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer's Instruction Manual for Safety & Comfort. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display - Toshiba M100 | User Manual - Page 72
details on using the AC adaptor to charge the Battery Pack, refer to Chapter 6, Power and Power incompatible adaptor could dam age your computer. TOSHIBA assumes no liability for any damage caused order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be - Toshiba M100 | User Manual - Page 73
15V port on the left side of the computer. Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN 15V indicator on the right of the display panel should glow. 3-7 - Toshiba M100 | User Manual - Page 74
GETTING STARTED User's Manual Turning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do - Toshiba M100 | User Manual - Page 75
/2000 setup When you first turn on the power, the computer's initial screen is the Microsoft Windows XP Professional or Windows 2000 Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or - Toshiba M100 | User Manual - Page 76
sake, it is best to save your data manually. 2. Data will be lost if you remove the battery or disconnect the AC adaptor before the save is TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. Otherwise, the computer will shut down in Standby mode. If battery - Toshiba M100 | User Manual - Page 77
to the steps below. 1. Open the Control Panel. 2. a. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. b. In Windows 2000, double-click the TOSHIBA Power Saver icon. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button - Toshiba M100 | User Manual - Page 78
GETTING STARTED User's Manual Data save in hibernation mode When you turn off the power mode depending on the setting of the TOSHIBA Power Saver feature. · To restore operation, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup. · If - Toshiba M100 | User Manual - Page 79
must be enabled. Refer to the System Power Mode item in TOSHIBA Power Saver Utility described in the Control Panel. a. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. b. In Windows 2000, double-click the TOSHIBA Power Saver icon. When you turn the power back on, you - Toshiba M100 | User Manual - Page 80
does not respond to your keyboard commands. There are two ways to restart the computer system: 1. If you are using Windows XP, click start then click Turn down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key - Toshiba M100 | User Manual - Page 81
16 Bluetooth wireless technology 4-16 Wireless communication switch 4-17 Wireless communication Indicator 4-17 LAN 4-18 LAN cable types 4-18 Connecting LAN cable 4-18 Disconnecting LAN cable 4-19 Using the microphone 4-20 Using the internal modem 4-20 Region selection 4-21 Properties menu - Toshiba M100 | User Manual - Page 82
Cleaning the computer 4-24 Moving the computer 4-25 Heat dispersal 4-25 OPERATING BASICS - Toshiba M100 | User Manual - Page 83
push it with your finger tip in the direction you want to move the on-screen pointer. ACCUPOINT II ACCUPOINT II CONTROL BUTTONS Figure 4-1 AccuPoint II and control buttons Two large buttons below the keyboard are used like the buttons on a mouse pointer. Press a button to select a menu item or - Toshiba M100 | User Manual - Page 84
User's Manual Click: Press a large button once Double-click: Press twice Drag and drop: Press to select the material you want to move. Leave your finger on the AccuPointII after the second button and move the material. AccuPoint II precautions Certain conditions can affect the on-screen pointer when - Toshiba M100 | User Manual - Page 85
hand into the Slim Select Bay slot. 2. Before removing or inserting a second battery pack, turn off the computer's power. NOTE: The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules - Toshiba M100 | User Manual - Page 86
User's Manual 4. Grasp the DVD-ROM drive and slide it out. CAUTION: The DVD-ROM drive and other Slim Select Bay modules can become hot with use. - Toshiba M100 | User Manual - Page 87
Using optical media drives Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. - Toshiba M100 | User Manual - Page 88
object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. 15mm Diameter 1.0mm Figure 4-6 Manual release with the eject hole 2. Pinch the drawer gently and pull until it is fully opened. Figure 4-7 Pulling the drawer open 3. Lay the CD/DVD - Toshiba M100 | User Manual - Page 89
Using optical media drives NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure - Toshiba M100 | User Manual - Page 90
User's Manual Figure 4-9 Closing the CD/DVD drawer Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-10. CAUTION: Do not - Toshiba M100 | User Manual - Page 91
Writing CDs on CD-RW/DVD-ROM drive Figure 4-10 Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. Writing CDs on CD-RW/DVD-ROM drive Depending on the type of drive installed, you may be able to write CDs. The CDRW/DVD-ROM drive lets you write as - Toshiba M100 | User Manual - Page 92
Manual MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Multi-Speed MITSUBISHI CHEMICAL CORPORATION High-Speed RICOH Co.,Ltd. CD-RW: Ultra-Speed MITSUBISHI CHEMICAL CORPORATION CD-RW: TOSHIBA such as a screen saver which can - Toshiba M100 | User Manual - Page 93
the steps below before you write or rewrite a Data CD/DVD. 1. Right-click Data BOX and select Options to display the DATA DISC Option window. 2. Mark the Record and Verify check box and select Byte compare. 3. Click the OK button. The "Record and Verify" function automatically checks whether data - Toshiba M100 | User Manual - Page 94
User's Manual Media care This section provides tips on protecting data stored on your CD/DVDs and magnetic surface. 6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. 4-12 OPERATING BASICS - Toshiba M100 | User Manual - Page 95
you use the diskette drive. Do not press the eject button, disconnect a drive cable or turn off the computer while the light is glowing. Doing so could destroy data from the diskette drive or if you use an OS that does not support USB, you must set the USB-FDD Legacy Emulation feature in HW Setup to - Toshiba M100 | User Manual - Page 96
User's Manual Connecting the USB diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-12. NOTE: Make sure the - Toshiba M100 | User Manual - Page 97
. Foreign particles inside the diskette's jacket can damage the magnetic surface. 6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. 4-15 OPERATING BASICS - Toshiba M100 | User Manual - Page 98
the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth wireless technology eliminates the need for cables between electronic devices such as desktop computers - Toshiba M100 | User Manual - Page 99
Wireless communications Worldwide operation The Bluetooth radio transmitter and receiver operates in the 2.45 GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices. The link is - Toshiba M100 | User Manual - Page 100
an optional memory module while Wake-up on LAN is enabled. NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. LAN cable types CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer - Toshiba M100 | User Manual - Page 101
you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer's LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub. 4-19 OPERATING BASICS - Toshiba M100 | User Manual - Page 102
User's Manual Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speakers, "howling" - Toshiba M100 | User Manual - Page 103
Programs, point to TOSHIBA Internal Modem and click Region Select Utility. 2. The Region Selection icon will appear in the Windows Task Bar. 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also - Toshiba M100 | User Manual - Page 104
User's Manual Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can dialog box is displayed if current settings for region code and telephony location are incorrect. Modem Selection If the computer cannot recognize the internal modem - Toshiba M100 | User Manual - Page 105
that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below. WARNING: The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular - Toshiba M100 | User Manual - Page 106
Manual CAUTION: Do not pull on the cable or move the computer while the cable cable from the computer in the same manner. 3. In the same way, pull the cable's other connector out of the computer. Cleaning the computer To help ensure long, trouble clean cloth and wipe the screen gently with the cloth. - Toshiba M100 | User Manual - Page 107
trouble interface ports are located). ❑ Close all Save Mode window in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed. Performance Uses a combination of the fan and lowering the CPU processing speed. Battery - Toshiba M100 | User Manual - Page 108
User's Manual When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed. NOTE: If the CPU - Toshiba M100 | User Manual - Page 109
Soft keys: Fn key combinations 5-2 Emulating keys on enhanced keyboard 5-2 Hotkeys 5-4 Fn Sticky key 5-6 Windows special keys 5-6 Keypad overlay 5-6 Turning on the overlays 5-7 Temporarily using normal keyboard (overlay on 5-8 Temporarily using overlay (overlay off 5-8 Temporarily changing - Toshiba M100 | User Manual - Page 110
THE KEYBOARD - Toshiba M100 | User Manual - Page 111
the upper- and lowercase letters, numbers, punctuation marks, and special symbols that appear on the screen. There are some differences, however, between using a typewriter and using a computer keyboard: ❑ Letters and numbers produced in computer text vary in width. Spaces, which are created by - Toshiba M100 | User Manual - Page 112
User's Manual F1 ... F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features - Toshiba M100 | User Manual - Page 113
information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off. Press Fn + Enter to simulate Enter on the enhanced keyboard's numeric keypad. Press Fn + Ctrl to simulate the enhanced - Toshiba M100 | User Manual - Page 114
a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be through the Plugged in or Running on batteries item of the TOSHIBA Power Saver Properties window in TOSHIBA Power Saver. Standby: When you press - Toshiba M100 | User Manual - Page 115
setting through the Monitor brightness item of the Power Save Mode window in TOSHIBA Power Saver. LCD Display Brightness: Pressing Fn + F7 setting through the Monitor brightness item of the Power Save Mode window in TOSHIBA Power Saver. NOTE: You cannot change the display brightness for about - Toshiba M100 | User Manual - Page 116
User's Manual Wireless setting: If your computer has both Bluetooth and TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an "F number" key. Windows special keys The keyboard provides two keys that have special functions in Windows - Toshiba M100 | User Manual - Page 117
. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay 5-7 THE KEYBOARD - Toshiba M100 | User Manual - Page 118
Manual Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard the normal keyboard, you can temporarily Check the keyboard indicators. to return to normal keyboard operation. Temporarily changing modes generated using normal keyboard operation. But - Toshiba M100 | User Manual - Page 119
Generating ASCII characters With the overlay off: 1. Hold Alt + Fn. 2. Using the overlay keys, type the ASCII code. 3. Release Alt + Fn, and the ASCII character appears on the display screen. 5-9 THE KEYBOARD - Toshiba M100 | User Manual - Page 120
User's Manual 5-10 THE KEYBOARD - Toshiba M100 | User Manual - Page 121
off 6-13 Extending battery life 6-13 Replacing the battery pack 6-14 Removing the battery pack 6-14 Installing the battery pack 6-15 TOSHIBA Password Utility 6-16 User password 6-16 Supervisor password 6-17 Starting the computer by password 6-18 Power-up modes 6-18 Windows utilities 6-18 - Toshiba M100 | User Manual - Page 122
POWER AND POWER-UP MODES - Toshiba M100 | User Manual - Page 123
details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer's operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is - Toshiba M100 | User Manual - Page 124
-UP MODES User's Manual Table 6-1 Power conditions continued Power on Power off (no operation) AC adaptor connected 2nd battery fully charged • Operates • No charge • LED: 2nd battery green DC IN 15V green • No charge • LED: 2nd battery green DC IN 15V green 2nd battery partially charged or - Toshiba M100 | User Manual - Page 125
to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a secondary battery are installed, the computer does not shut down until the charge in both - Toshiba M100 | User Manual - Page 126
Manual Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN 15V and Power indicators on the system indicator alert you to the computer's operating capability and battery charge status. Battery indicators Check the Battery orange Indicates a problem with the power - Toshiba M100 | User Manual - Page 127
main and secondary (option) ❑ RealTimeClock(RTC)battery Main battery When the AC adaptor is not connected, the computer's main power source is a removable lithium ion battery pack, also referred to in this manual as the main battery. You can purchase additional battery packs for extended use of the - Toshiba M100 | User Manual - Page 128
maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key - Toshiba M100 | User Manual - Page 129
battery pack CAUTION: The computer's RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery in death or serious injury, if you do not follow instructions. Caution: Indicates a potentially hazardous situation, which if not - Toshiba M100 | User Manual - Page 130
. Never strike it with a hammer or other object. Never step on it. 5. Never try to charge the battery pack in any manner other than that described in the user's manual. Never connect the battery pack to a plug socket or to an automobile's cigarette lighter socket. It may rupture or ignite. 6. Use - Toshiba M100 | User Manual - Page 131
odor, excessive heat, discoloration or deformation. Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the - Toshiba M100 | User Manual - Page 132
mode only if Hibernation is enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. You must recharge a battery pack when it becomes discharged. Procedures To recharge a battery pack while it is installed in the computer, connect the - Toshiba M100 | User Manual - Page 133
4 to 12 or longer 4 to 12 or longer Power off 2.5 2.5 RTC battery 8 Doesn't charge Battery charging notice The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. Also, to ensure - Toshiba M100 | User Manual - Page 134
POWER AND POWER-UP MODES User's Manual Monitoring battery capacity Remaining battery power can be monitored in the Power Save Modes window in TOSHIBA Power Saver of Windows. NOTES: 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The - Toshiba M100 | User Manual - Page 135
you store your programs and data. ❑ Closing the display when you are not using the keyboard saves power. ❑ Operating time decreases at low temperatures. ❑ The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the - Toshiba M100 | User Manual - Page 136
apply impact; do not scratch or break the casing and do not twist or bend the battery pack. 1. Save your work. 2. Turn the computer's power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Turn the computer upside down with the back of the computer facing - Toshiba M100 | User Manual - Page 137
of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer's power is off and all cables are disconnected. 2. Insert the battery pack. BATTERY PACK Figure 6-2 Installing the battery pack 6-15 - Toshiba M100 | User Manual - Page 138
-UP MODES User's Manual 3. Secure the battery lock. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. NOTE: Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility - Toshiba M100 | User Manual - Page 139
Windows 2000 Start -> Programs -> TOSHIBA SD Card Utilities -> TOSHIBA SD Memory Card Format Windows XP Start -> All Programs -> TOSHIBA SD Card Utilities -> TOSHIBA password. To set a supervisor password, execute the file TOSUP.EXE. The file is located at: C:\Program Files\Toshiba\Windows - Toshiba M100 | User Manual - Page 140
back on to retry password entry. Power-up modes The computer has the following power-up modes: ❑ Boot: Computer shuts down without saving data. Always save your work before you turn the in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. 6-18 - Toshiba M100 | User Manual - Page 141
to enter Standby mode and Fn + F4 to enter Hibernation. See Chapter 5, Keyboard for details. Panel power off You can set up your computer so that power If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed. - Toshiba M100 | User Manual - Page 142
POWER AND POWER-UP MODES User's Manual 6-20 - Toshiba M100 | User Manual - Page 143
Chapter 7 HW Setup HW Setup 7-1 Accessing HW Setup 7-1 HW Setup window 7-1 HW SETUP - Toshiba M100 | User Manual - Page 144
HW SETUP - Toshiba M100 | User Manual - Page 145
settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, device config and parallel/printer. Accessing HW Setup If you are using Windows XP, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup to run HW Setup. If you are - Toshiba M100 | User Manual - Page 146
it can control. (Default) All Devices BIOS sets all devices. Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel customize your computer's display settings for either the internal LCD screen or for an external monitor. 7-2 - Toshiba M100 | User Manual - Page 147
On Display Let you use the display to be used when the computer is booted. (This setting is only available while Windows Logo is displaying and not available after Windows Desktop is displayed.) Auto-Selected Selects an external monitor if one is connected. Otherwise, it selects the internal LCD - Toshiba M100 | User Manual - Page 148
LAN, diskette drive and HDD. You can override the settings and manually select a boot device by pressing one of the following keys while drive. NOTES: 1. PC card HDD boot is supported only by slot 0 on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. 2. When you assign a PC - Toshiba M100 | User Manual - Page 149
the left/right cursor keys to highlight the boot device you want and press Enter. NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2. In this computer, CD-ROM refers to the DVD-ROM or CDRW/DVD-ROM drives - Toshiba M100 | User Manual - Page 150
HW SETUP User's Manual 2nd HDD −> PC Card −> Built-in HDD The computer will look key equivalent will let you use "Hotkeys" by pressing the set combination instead of the Fn key. (PS/2 keyboard only) Disabled Fn Equivalent No Fn key equivalent (Default) Left Ctrl + Left Alt Right Ctrl + Right - Toshiba M100 | User Manual - Page 151
Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Enables the USB KB/Mouse Legacy Emulation. (Default - Toshiba M100 | User Manual - Page 152
HW SETUP User's Manual NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. Built-in LAN Enabled Enables built-in LAN functions. (Default) Disabled Disables built-in LAN functions. 7-8 - Toshiba M100 | User Manual - Page 153
card care 8-6 Memory expansion 8-7 Installing memory module 8-8 Removing memory module 8-10 Additional battery pack 8-11 Slim Select Bay 2nd battery pack 8-12 Installing 8-12 Removing 8-12 Universal AC adaptor 8-13 Battery charger 8-13 Hard disk drive pack 8-13 Removing the HDD pack 8-14 - Toshiba M100 | User Manual - Page 154
OPTIONAL DEVICES - Toshiba M100 | User Manual - Page 155
. The following optional devices are available from your TOSHIBA dealer: Cards/memory ❑ PC cards ❑ SD cards ❑ Memory expansion Power devices ❑ Additional battery pack ❑ Slim Select Bay 2nd battery pack ❑ Universal AC adaptor ❑ Battery charger Peripheral devices ❑ Hard disk drive pack ❑ Slim - Toshiba M100 | User Manual - Page 156
OPTIONAL DEVICES User's Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC - Toshiba M100 | User Manual - Page 157
appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1. a. In Windows XP, open the Safely Remove Hardware icon on the system tray and disable the PC card. b. In Windows 2000, open the Unplug or Eject Hardware icon on the system tray and disable the PC card - Toshiba M100 | User Manual - Page 158
OPTIONAL DEVICES User's Manual SD cards The computer is equipped with an SD utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format. In order to run TOSHIBA SD memory card format, select [Start] - [All Programs] [TOSHIBA SD card utilities] - [TOSHIBA SD - Toshiba M100 | User Manual - Page 159
you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. a. In Windows XP, open the Safely Remove Hardware icon on the system tray and disable the SD card. b. In Windows 2000, open the Unplug or Eject Hardware icon on the system tray and disable the SD card - Toshiba M100 | User Manual - Page 160
OPTIONAL DEVICES User's Manual SD CARD SD CARD INDICATOR Figure 8-4 Removing an SD card CAUTIONS: 1. lock position, if you do not want to record data. 1. Do not write to an SD card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove an SD card while read/write is - Toshiba M100 | User Manual - Page 161
with two memory module sockets beneath the keyboard. You can increase the amount of RAM by installing an additional memory or replacing mat that generates static electricity. CAUTION: Use only memory modules approved by TOSHIBA. CAUTION: Do not try to install or remove a memory module under - Toshiba M100 | User Manual - Page 162
in Chapter 3. 2. Remove all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power keyboard brace and lift up to release latches and remove the brace. Figure 8-5 Removing the keyboard brace 6. Remove two screws securing the keyboard - Toshiba M100 | User Manual - Page 163
up the keyboard. Do not try to disconnect this cable. 8. Push the module down so that it lies flat and is secured by two latches on either side. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. NOTE: The - Toshiba M100 | User Manual - Page 164
on the computer. Be sure the ribbon cable lies flat and is not pinched. 10. Secure the keyboard with two screws. 11. Set the keyboard brace into its groove and press down to secure the latches. 12. Turn the computer upside down and replace the battery pack (refer to Chapter 6, Power and Power - Toshiba M100 | User Manual - Page 165
may cause memory access problems. LATCHES Figure 8-8 Removing the memory module 7. Rotate the keyboard back into place and secure the keyboard brace as described in the previous section. 8. Turn the computer upside down and replace the battery pack. Additional battery pack You can increase - Toshiba M100 | User Manual - Page 166
OPTIONAL DEVICES User's Manual Slim Select Bay 2nd battery pack You can install a secondary battery pack in the computer's Slim Select Bay. The battery comes with an adaptor. For details on using the adaptor, follow the steps below. For details on installing modules in the Slim Select Bay, refer - Toshiba M100 | User Manual - Page 167
and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. Battery charger The battery charger (PA3091U) provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two Lithium-ion - Toshiba M100 | User Manual - Page 168
8-12. 1. Set the computer to boot mode and turn off the power. 2. Disconnect the AC adaptor and all external cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-Up Modes.) 4. Remove two screws securing the HDD pack cover - Toshiba M100 | User Manual - Page 169
Slim Select Bay HDD adaptor Installing the HDD pack To install the HDD pack, follow the steps below. 1. Insert the HDD pack into the slot. 2. Fold over the plastic tab so that it goes into the HDD pack slot. Press to ensure a firm connection. OPTIONAL DEVICES Figure 8-13 Installing the HDD pack 3. - Toshiba M100 | User Manual - Page 170
OPTIONAL DEVICES User's Manual 2. Insert the HDD and push forward to ensure a firm connection. Figure 8-15 Installing the HDD 3. Close the lid and slide the lock to the lock - Toshiba M100 | User Manual - Page 171
jack, line-in jack and separate ports for PS/2 mouse and PS/2 keyboard. The Port Replicator connects directly to the docking interface on the bottom of ❑ Externalmonitorport ❑ Parallelport ❑ Serialport ❑ PS/2 mouse port ❑ PS/2 keyboard port ❑ DCIN15Vsocket ❑ Security lock slot ❑ Audio line-in, line - Toshiba M100 | User Manual - Page 172
remove all cables connected to the computer. 2. The Portégé M100 do not support the DVI port on the Port Replicator. External monitor An external analog monitor can be connected to the external monitor port on the computer and Slim Port Replicator. The computer supports VGA and Super VGA video modes - Toshiba M100 | User Manual - Page 173
that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ❑ Do not transfer data in areas where static electricity is easily generated or in areas subjected to - Toshiba M100 | User Manual - Page 174
You may need to install drivers for your i.LINK devices. ❑ Not all i.LINK devices have been tested, therefore, compatibility with all i.LINK devices cannot be guaranteed. ❑ Use S100, S200 or S400 cables no longer than three meters. ❑ Some devices might not support standby or automatic off functions - Toshiba M100 | User Manual - Page 175
lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer. Figure 8-18 Security lock 8-21 - Toshiba M100 | User Manual - Page 176
OPTIONAL DEVICES User's Manual 8-22 - Toshiba M100 | User Manual - Page 177
Chapter 9 Troubleshooting Problem solving process 9-1 Preliminary checklist 9-1 Analyzing the problem 9-2 Hardware and system checklist 9-3 System start-up 9-3 Self test 9-4 Power 9-4 Password 9-7 Keyboard 9-8 LCD panel 9-8 Hard disk drive 9-9 DVD-ROMdrive 9-10 CD-RW/DVD-ROMdrive 9-12 - Toshiba M100 | User Manual - Page 178
TROUBLESHOOTING - Toshiba M100 | User Manual - Page 179
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem - Toshiba M100 | User Manual - Page 180
If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. 9-2 TROUBLESHOOTING - Toshiba M100 | User Manual - Page 181
peripherals. Basic problems may occur in the following areas: ❑ System start-up ❑ AccuPoint II ❑ Self test ❑ PC card ❑ Power ❑ SD card ❑ Password ❑ Monitor ❑ Keyboard ❑ Sound system ❑ LCD check the following items: ❑ Self Test ❑ Power Sources ❑ Power-on Password TROUBLESHOOTING 9-3 - Toshiba M100 | User Manual - Page 182
resources are interrelated and any one could affect apparent power problems. This section provides checklists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource. In such case, contact your dealer. 9-4 TROUBLESHOOTING - Toshiba M100 | User Manual - Page 183
your dealer. Computer shuts down and its DC IN 15V indicator is flashing green Indicates a problem with the heat dispersal system. Please contact your dealer. TROUBLESHOOTING AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN 15V indicator. Refer - Toshiba M100 | User Manual - Page 184
User's Manual Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer. Battery If you suspect a problem with the battery - Toshiba M100 | User Manual - Page 185
discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. Password Problem Cannot enter password Procedure Refer to the Password section in Chapter 6, Power and Power-Up Modes. TROUBLESHOOTING 9-7 - Toshiba M100 | User Manual - Page 186
Keyboard and Chapter 7, HW Setup. Problem Some letter keys produce numbers Procedure Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is . Run the diagnostic test. Contact your dealer if the problems continue. TROUBLESHOOTING 9-8 - Toshiba M100 | User Manual - Page 187
Boot priority. Refer to Chapter 7, Boot Priority. Slow performance There may be a problem with your operating system files. Refer to your OS documentation. Your files may be fragmented reload the operating system and other files. If problems persist, contact your dealer. TROUBLESHOOTING 9-9 - Toshiba M100 | User Manual - Page 188
, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software's needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM,DVD-Video TROUBLESHOOTING 9-10 - Toshiba M100 | User Manual - Page 189
problems persist, contact your dealer. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard writing. If problems persist, contact your dealer. TROUBLESHOOTING 9-11 - Toshiba M100 | User Manual - Page 190
Manual CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem or hardware configuration may be causing a problem. Make sure the hardware configuration matches your the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM,DVD-Video CD-ROM: CD- - Toshiba M100 | User Manual - Page 191
in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording - Toshiba M100 | User Manual - Page 192
your IrDA compatible device and related software. Problem Procedure Infrared devices do not work as expected Check that the device is problems persist, contact your dealer. Printer Refer to the troubleshooting and other relevant sections in your printer and software documentation. Problem - Toshiba M100 | User Manual - Page 193
ready to use). Inspect the cable connecting the printer to the window. The Pointing Device option should be set to Simultaneous to use both the AccuPoint II and an external PS/2 mouse. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices. TROUBLESHOOTING - Toshiba M100 | User Manual - Page 194
, contact your dealer. SD card Refer also to Chapter 8, Optional Devices. Problem SD card error occurs You cannot write to an SD card Procedure Reseat the SD card to make sure it is firmly connected. Check the card's documentation. Make sure the card is not write protected. TROUBLESHOOTING 9-16 - Toshiba M100 | User Manual - Page 195
. Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Sound system Problem No sound is heard Procedure Adjust the volume control dial. Check the software volume settings. 9-17 TROUBLESHOOTING - Toshiba M100 | User Manual - Page 196
the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard. If these devices do not work, make sure the USB KB/Mouse Legacy Emulation item in HW Setup is set to Enabled. If problems persist, contact your dealer. TROUBLESHOOTING - Toshiba M100 | User Manual - Page 197
system checklist Modem Refer to the online help files for Appendix C and D. Problem Procedure Communication software can't initialize modem Make sure the computer's internal modem the error control setting in your is quickly replaced by communications application. TROUBLESHOOTING 9-19 - Toshiba M100 | User Manual - Page 198
's Manual NO Windows Media™ Player open? The system might not enter Standby/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/Hibernation. If problems persist, contact your dealer. TROUBLESHOOTING - Toshiba M100 | User Manual - Page 199
battery. When both beeps sound, 3. Remove the memory module. both memories in slot A 4. Replace the battery and/or connect the AC and B are defective.) adaptor. 5. Turn on the power. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable - Toshiba M100 | User Manual - Page 200
PC card cannot operate simultaneously. If problems persist, contact your dealer. i.LINK (IEEE1394) Problem i.LINK device does not function Procedure Make sure the cable is securely connected to the computer and to the device. Make sure the device's power is turned on. TROUBLESHOOTING 9-22 - Toshiba M100 | User Manual - Page 201
and system checklist Reinstall the drivers. Open the Windows Control Panel and double-click the Add New Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer. Real Time Clock Problem Procedure Thefollowingmessage The battery for RTC is wearing - Toshiba M100 | User Manual - Page 202
TOSHIBA, try the following: ❑ Review troubleshooting sections in the documentation for software and peripheral devices. ❑ If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions. Call the software company's technical support - Toshiba M100 | User Manual - Page 203
. 351, Jinzang Road, Pudong New Area, Shanghai, P.R. China 201206 Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra Technopark Singapore 119968 TOSHIBA support United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 - Toshiba M100 | User Manual - Page 204
User's Manual United Kingdom TOSHIBA Information Systems (U.K.) Ltd. TOSHIBA Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany 9-26 TROUBLESHOOTING - Toshiba M100 | User Manual - Page 205
Appendixes Appendix A Specifications A-1 Appendix B Display Controller and Modes B-1 Appendix C AT Commands C-1 Appendix D S-registers D-1 Appendix E V.90 E-1 Appendix F Wireless LAN F-1 Appendix G AC Power Cord and Connectors G-1 Appendix H Internal Modem Guide H-1 Appendix I Parts - Toshiba M100 | User Manual - Page 206
APPENDIXES - Toshiba M100 | User Manual - Page 207
This appendix summarizes the computer's technical specifications. Physical Dimensions Size With TFT display 270(w)×248(d)×31.7/37.4(h)millimeters Weight 2.00kg typical*,configured with:12.1"XGA-TFT,256MB RAM,40GB HDD,DVDROM drive,Wireless LAN(Intel) * Weight will vary depending on whether - Toshiba M100 | User Manual - Page 208
User's Manual APPENDIX A Computer 15VDC 3.0 amperes Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer's speaker Communication specifications - Toshiba M100 | User Manual - Page 209
APPENDIX A Error correcting Data compression Power supply MNP class 4 and ITU-T V.42 MNP class 5 and ITU-T V.42bis +3.3V (supplied by computer) Appendix A A-3 - Toshiba M100 | User Manual - Page 210
APPENDIX A User's Manual A-4 - Toshiba M100 | User Manual - Page 211
uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen. Software written for a given video mode will run on any computer that supports the mode. The computer's display controller supports all VGA and SVGA modes, the most widely - Toshiba M100 | User Manual - Page 212
APPENDIX B User's Manual Video modes The computer supports video modes defined in the tables below. If your Also, if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode. Table1 Video modes (VGA) Video Type Resolution mode - Toshiba M100 | User Manual - Page 213
LCD matrix colors (pels) CRT colors Scanning frequency Vertical (Hz) D VGA 320 × 200 8 × 8 16 of 256K 16 of 256K 70 Grph Pels E VGA 640 × 200 8 × 8 16 of 256K 16 of 256K 70 Grph Pels F VGA 640 × 350 8 × 14 Mono Mono 70 Grph Pels 10 VGA 640 × 350 8 × 14 16 of 256K 16 of 256K - Toshiba M100 | User Manual - Page 214
User's Manual APPENDIX B Table 2 Video modes (SVGA) Resolution 640 × 480 LCD colors 256/256K 800 × 600 256/256K 1024 × 768 256/256K 1280 85 100 60 75 85 60 75 85 100 60 75 85 60 75 Caution: Some SVGA modes are not supported at LCD+CRT simultaneous B-4 mode and LCD+CRT Multi Monitor mode. - Toshiba M100 | User Manual - Page 215
100 1920 × 1440 64K/64K 64K/64K 60 (Virtual) 75 85 2048 × 1536 64K/64K 64K/64K 60 75 Caution: Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode. B-5 - Toshiba M100 | User Manual - Page 216
User's Manual APPENDIX B Table 2 Video modes (SVGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 ) 75 85 2048 × 1536 16M/16M 16M/16M 60 75 Caution: Some SVGA modes are not supported at LCD+CRT simultaneous B-6 mode and LCD+CRT Multi Monitor mode. - Toshiba M100 | User Manual - Page 217
manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value - Toshiba M100 | User Manual - Page 218
APPENDIX C User's Manual A Answer command This command instructs the modem to go off-hook modem is at 300 bps (default). Result Codes: OK n=0,1,15,16 ERROR Otherwise Dn Dial This command instructs the modem to dial a telephone number. Enter n (the telephone number and any modifiers) after the ATD - Toshiba M100 | User Manual - Page 219
or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while Codes: OK n=0,1 ERROR Otherwise Hn Hook control This command instructs the modem to go on-hook to disconnect a call, I0 Returns modem identity string and driver version number. I3 Same as I0 - Toshiba M100 | User Manual - Page 220
C User's Manual Ln Monitor speakers volume This command sets speakers volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speakers mode This command turns the speakers on or off - Toshiba M100 | User Manual - Page 221
APPENDIX C Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to - Toshiba M100 | User Manual - Page 222
User's Manual APPENDIX C T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed result codes will be used by the modem. Command Dial tone Busy signal Supported Result detect detect Code X0 Disable Disable X1 Disable Disable X2 Enable Disable X3 - Toshiba M100 | User Manual - Page 223
receives. Enabled: The modem monitors for busy tones. Result Codes: OK n=0,1,2,3,4,5 ERROR Otherwise Zn Recall stored profile The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied. If no parameter is specified, zero is assumed. Either Z0 - Toshiba M100 | User Manual - Page 224
APPENDIX C User's Manual &C0 The state of the carrier from the remote modem is ignored. the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: OK n=0,1,2,3 ERROR Otherwise &F Load factory settings This - Toshiba M100 | User Manual - Page 225
33% - 67% make/break ratio at 20 pulses per second. Result Codes: OK n=0,1,2 ERROR Otherwise &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. C-9 - Toshiba M100 | User Manual - Page 226
work properly, the modem must be off-line. Result Codes: OK n=0 CONNECT n=1 ERROR Otherwise &V Display Current Configuration This command displays the current configuration of the modem. If nonvolatile memory is supported stored number" where n is the location 0-3 to which the number should be - Toshiba M100 | User Manual - Page 227
APPENDIX C Appendix C \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control - Toshiba M100 | User Manual - Page 228
APPENDIX C User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: - Toshiba M100 | User Manual - Page 229
automatically when you modify corresponding settings in your communication software. If you choose, however, you can display and edit the contents of the registers manually when the modem is in command mode. If the value is out of the acceptable range, then an error is generated. This chapter - Toshiba M100 | User Manual - Page 230
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do - Toshiba M100 | User Manual - Page 231
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127,ASCIIdecimal Default: 10 (line feed) Units: ASCII S5 Command line - Toshiba M100 | User Manual - Page 232
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon - Toshiba M100 | User Manual - Page 233
S37 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14 S37 = 15 S37 = 16 S37 = 17 S37 = 18 S37 = 19 maximum modem speed reserved 1200/75 bps 300 bps reserved 1200 bps 2400 bps 4800 bps 7200 bps 9600 - Toshiba M100 | User Manual - Page 234
User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code OK CONNECT RING NO CARRIER Numeric 0 1 2 3 ERROR 4 - Toshiba M100 | User Manual - Page 235
Appendix D Result Code DELAYED*2 BLACKLISTED*2 BLACKLIST FULL*2 Numeric 88 89 90 Description Delay is in effect for the dialed number Dialed number is blacklisted Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the - Toshiba M100 | User Manual - Page 236
User's Manual D-8 APPENDIX D - Toshiba M100 | User Manual - Page 237
TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports one V.90 capable modem is connected to another. The TOSHIBA Internal modem will select automatically V.34 if the remote - Toshiba M100 | User Manual - Page 238
User's Manual Table E-1 Result codes for a V.90 connection No. Result code Description 70 CONNECT 32000 EC* Connection at 32000 bits/s 72 CONNECT 36000 EC* Connection at 36000 - Toshiba M100 | User Manual - Page 239
Appendix E AT Command -V90=* V.90DialLineRate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90disabled -V90=1 V.90 enabled: automatic speed selection - maximum modem speed (default) E-3 APPENDIX E - Toshiba M100 | User Manual - Page 240
User's Manual E-4 APPENDIX E - Toshiba M100 | User Manual - Page 241
and running, with a minimum of parameters. Card specifications Form Factor Capability Network Operating System Media Access Protocol Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) „ Microsoft Windows®Networking „ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) „ - Toshiba M100 | User Manual - Page 242
User's Manual APPENDIX F R-F Frequency „ Band 5 GHz (5150-5850 MHz) (Revision A, Turbo Mode) „ Band 2.4 GHz ( country/region, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio - Toshiba M100 | User Manual - Page 243
APPENDIX F Appendix F When installing Wireless LAN cards, the channel configuration is managed as follows: ‰ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When - Toshiba M100 | User Manual - Page 244
User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 42 50 58 152 160 5150-5850 MHz 5210 5250 5290 5760 5800 Note US only * - Toshiba M100 | User Manual - Page 245
outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size: Current rating: Minimum 2 meters Minimum 0.75 mm2 Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region's power - Toshiba M100 | User Manual - Page 246
APPENDIX G User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom UL approved CSA approved Australia BS approved Europe AS approved Approved by the appropriate agency G-2 - Toshiba M100 | User Manual - Page 247
or install the internal modem or to check the PTT label. 2. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. 3. Always remove the Battery Pack and disconnect the AC Adaptor before removing the base cover. 4. Be careful - Toshiba M100 | User Manual - Page 248
rest and secure it with three screws. 11. Connect the keyboard cable and seat the keyboard. 12. Secure the keyboard with two screws and install the keyboard brace. 13. Turn the computer upside down. 14. Secure three screws. Installing the battery pack Refer to chapter 6 for details on installing the - Toshiba M100 | User Manual - Page 249
lift it out. 11. Seat the palm rest and secure it with three screws. 12. Connect the keyboard cable and seat the keyboard. 13. Secure the keyboard with two screws and install the keyboard brace. 14. Turn the computer upside down. 15. Secure three screws. APPENDIX H The internal modem is approved - Toshiba M100 | User Manual - Page 250
APPENDIX H User's Manual H-4 - Toshiba M100 | User Manual - Page 251
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices. I-1 APPENDIX I - Toshiba M100 | User Manual - Page 252
APPENDIX I User's Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left - Toshiba M100 | User Manual - Page 253
manual. Alternate naming is included for reference. Abbreviations AC: alternating current ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CMOS component interconnect RAM: random access - Toshiba M100 | User Manual - Page 254
Association VGA: video graphics array VRT: voltage reduction technology A AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing, and - Toshiba M100 | User Manual - Page 255
starts or restarts the computer. The program reads instructions from a storage device into the computer's memory the smallest addressable unit within the system. C BIOS: Basic Input Output System. The firmware that , called chips, which perform a specific function or increase the capabilities of the - Toshiba M100 | User Manual - Page 256
supports two CMOS technology can be tightly packaged and are highly reliable. cold start: Starting a computer that is currently off (turning on the power). COM1, COM2, COM3 and COM4: The names assigned to the serial and communication ports. commands: Instructions you enter at the terminal keyboard - Toshiba M100 | User Manual - Page 257
your system works. You use the HW Setup program to control your system configuration. control keys: A key or sequence of keys you enter from the keyboard to initiate a particular function within a program. controller: Built-in hardware and software that controls the functions of a specific internal - Toshiba M100 | User Manual - Page 258
MS-DOS loads when you turn the computer on. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). dialog box: A window that accepts user input to make system settings or record - Toshiba M100 | User Manual - Page 259
instruction. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support. folder: An icon in Windows firmware: A set of instructions built into the hardware Fn-esse: A TOSHIBA utility that lets - Toshiba M100 | User Manual - Page 260
, can be used to set system parameters, such as speakers volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can - Toshiba M100 | User Manual - Page 261
keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific that uses the large scale integration. M main board: See motherboard. MDA: Monochrome Display Adaptor. A video display protocol defined by - Toshiba M100 | User Manual - Page 262
screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions or graphic images. See CRT. motherboard: A name sometimes used to allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor - Toshiba M100 | User Manual - Page 263
odd, or even. password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, called a pel. plug and play: A capability with Windows that enables the system to automatically recognize connections of external devices - Toshiba M100 | User Manual - Page 264
A TOSHIBA utility that set of instructions a reset'). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. resume: A feature that lets you turn off the power without first exiting a program and retain your data in RAM. When you turn on the computer, the screen - Toshiba M100 | User Manual - Page 265
keyboard, change some configuration options, stop program execution, and access the numeric keypad overlay. software: The set of programs, procedures and related documentation associated with a computer system. Specifically : A typewriter-like keyboard and CRT display screen connected to the computer - Toshiba M100 | User Manual - Page 266
V VGA: Video graphics array is an industry standard video adaptor that lets you run any popular software. volatile memory: Random access memory (RAM) suspended. warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application - Toshiba M100 | User Manual - Page 267
Battery charger 1-13, 8-13 Battery pack 1-5, 6-5 additional 1-12, 8-11 location 2-5 replacing 6-14 2nd, See Slim Select Bay Bluetooth 1-8 using 4-16 problems problems 9-13 using 4-13 Display 1-5, 2-7, See also Video modes and Monitor external automatic power off 1-9 controller 1-5, Appendix B driver - Toshiba M100 | User Manual - Page 268
work habits 3-4 Expansion memory, SeeMemory expansion F Fn + Alt (enhanced keyboard simulation) 5-9 Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound drive 1-4, 1-13 automatic power off 1-9 installing 8-15 problems 9-9 removing 8-14 Hibernation 1-10, 5-5 Hotkeys 1-9, 5-4 - Toshiba M100 | User Manual - Page 269
, See Keypad overlay O Operating system, See Windows Overlay, See Keypad overlay P Panel power on/off, See Power Password power on 1-9 starting the computer with 6-18 supervisor 1-11, 6-17 user 6-16 PC card 1-6 installing 8-2 location of slots 2-2 problems 9-15 removing 8-3 Pointing devices, See - Toshiba M100 | User Manual - Page 270
9-20 support from TOSHIBA 9-24 Index-4 system start-up 9-3 USB 9-18 Wireless LAN 9-21 Processor 1-3 R Real time clock battery, See Battery Recovery CD-ROM 3-14 S Screen, See Display ScrLock (Fn + F12), See Soft keys SD card 1-6 indicator 2-3 installing 8-5 location of slot 2-3 problems 9-16 - Toshiba M100 | User Manual - Page 271
off 1-9 T TOSHIBA Console button 1-9 TOSHIBA Console 1-12 TOSHIBA Controls 1-12 TOSHIBA Power Saver 1-11 Troubleshooting, See Problems U Utilities list 1-11 USB 1-6 location 2-4 problems 9-18 V Video modes, Appendix B Video RAM 1-5 Volume control, See Sound system W Windows XP setup 3-9 Windows 2000 - Toshiba M100 | User Manual - Page 272
INDEX User's Manual Index-6
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
 |
 |
TOSHIBA Portégé
M100
Portable Personal Computer
User’s Manual