Toshiba RD-X2 Owners Manual - Page 18

Before operating this recorder

Get Toshiba RD-X2 PDF manuals and user guides View all Toshiba RD-X2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Introduction Before operating this recorder Is your recorder ready? Refer to the supplied "INSTALLATION GUIDE" manual and finish the necessary preparations. Turning the power on (This owner's manual instructions are based on the assumption that all proper connections have been completed and the TV is turned on.) Press the ON/STANDBY button on the front panel of the recorder or the power button on the remote control. ON/STANDBY indicator Loading a disc Check disc compatibility beforehand (page 6) and use a proper playable disc. Caution • Keep your fingers well clear of the disc tray. Neglecting this may causes serious personal injury. Keep a close watch on children. • Do not use a cracked, deformed, or repaired disc. 1 Open the disc tray. Press the button on the front panel or the OPEN/CLOSE button on the remote control. button ON/STANDBY button Power button CHANNEL button When the power turns on, the ON/STANDBY indicator changes from red (standby mode) to green (operation). After a few seconds, a start-up screen appears. The following icon appears at the top right corner of the screen. e.g. Loading When this icon disappears, the recorder is ready to operate. If the DVD-RAM drive contains a disc, it takes a little longer to start up. Viewing TV channels through this recorder After turning the power on, the recorder will output TV channel signals to the connected TV (also in the stop mode). You can select a desired channel by pressing the CHANNEL buttons. OPEN/CLOSE button 2 Insert a disc. Disc without a cartridge Insert with the playback side down. Disc size varies depending on the disc. Place a disc to fit the guide. If a disc is out of the guide, it may result in damage to the disc or malfunction. 12cm (43/4 in.) disc: Set a disc so that the 2 stoppers in the opening side can hold the rim. Do not cover them. 8cm (31/4 in.) disc: Place a disc in the inside hollow. 18 *RD-X2.Ope(US)p018-026 18 9/3/02, 11:23 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
18
Introduction
Is your recorder ready?
Refer to the supplied “INSTALLATION GUIDE” manual
and finish the necessary preparations.
Turning the power on
(This owner’s manual instructions are based on
the assumption that all proper connections have
been completed and the TV is turned on.)
Press the ON/STANDBY button on the front panel of
the recorder or the power button on the remote
control.
When the power turns on, the ON/STANDBY indicator
changes from red (standby mode) to green (operation).
After a few seconds, a start-up screen appears.
The following icon appears at the top right corner of
the screen.
When this icon disappears, the recorder is ready to
operate.
If the DVD-RAM drive contains a disc, it
takes a little longer to start up.
Viewing TV channels through this recorder
After turning the power on, the recorder will output TV
channel signals to the connected TV (also in the stop
mode).
You can select a desired channel by pressing the
CHANNEL buttons.
Before operating this recorder
Loading
e.g.
Loading a disc
Check disc compatibility beforehand (page 6) and use
a proper playable disc.
Caution
• Keep your fingers well clear of the disc tray. Neglecting this
may causes serious personal injury.
Keep a close watch
on children.
• Do not use a cracked, deformed, or repaired disc.
1
Open the disc tray.
Press the
button on the front panel or the
OPEN/CLOSE button on the remote control.
2
Insert a disc.
Disc without a car
tr
idge
Insert with the playback side down.
Disc size varies depending on the disc. Place a
disc to fit the guide. If a disc is out of the guide, it
may result in damage to the disc or malfunction.
OPEN/CLOSE button
button
12cm (4
3
/
4
in.) disc:
Set a disc so that the 2
stoppers in the opening
side can hold the rim. Do
not cover them.
8cm (3
1
/
4
in.) disc:
Place a disc in the inside
hollow.
Power button
CHANNEL button
ON/STANDBY button
ON/STANDBY indicator
*RD-X2.Ope(US)p018-026
9/3/02, 11:23 AM
18