Toshiba RD-XS32SU Owners Manual - Page 20

Before operating this recorder - installation manual

Get Toshiba RD-XS32SU PDF manuals and user guides View all Toshiba RD-XS32SU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Introduction Before operating this recorder Is your recorder ready? • Refer to the supplied "INSTALLATION GUIDE" manual and finish the necessary preparations. • Turn on the connected equipment such as a TV or audio system and select the input from the recorder. Turning the power on (This owner's manual instructions are based on the assumption that all proper connections have been completed and the TV is turned on.) Press ON/STANDBY on the front panel of the recorder or on the remote control. ON/STANDBY button Loading a disc Check disc compatibility beforehand ( and use a proper playable disc. page 6, 7) Caution • Keep your fingers well clear of the disc tray. Neglecting this may cause serious personal injury. Keep a close watch on children. • Do not use a cracked, deformed, or repaired disc. 1 Open the disc tray. Press on the front panel or the OPEN/CLOSE button on the remote control. button ON/STANDBY indicator ON/STANDBY button CHANNEL buttons OPEN/CLOSE button When the power turns on, the ON/STANDBY indicator changes from red (standby mode) to green (operation). After a few seconds, a start-up screen appears. The following icon appears at the top right corner of the screen. e.g. Loading When this icon disappears, the recorder is ready to operate. If the disc drive contains a disc, it takes a little longer to start up. Viewing TV channels through this recorder After turning the power on, the recorder will output TV channel signals to the connected TV (also in the stop mode). You can select a desired channel by pressing the CHANNEL or the number buttons. (These buttons can select channels of a connected cable box or satellite system, if "IR control" ( page 37, in "INSTALLATION GUIDE") is set to "On".) 2 Insert a disc. Disc without a cartridge Insert with the playback side down. There are two kinds of disc size. Place a disc to fit the guide. If a disc is out of the guide, it may result in damage to the disc or malfunction. Place a disc in the inside hollow. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
20
Is your recorder ready?
•
Refer to the supplied
“
INSTALLATION GUIDE
”
manual and finish the necessary preparations.
•
Turn on the connected equipment such as a TV or
audio system and select the input from the recorder.
Turning the power on
(This owner
’
s manual instructions are based on
the assumption that all proper connections have
been completed and the TV is turned on.)
Press ON/STANDBY on the front panel of the
recorder or on the remote control.
When the power turns on, the ON/STANDBY indicator
changes from red (standby mode) to green (operation).
After a few seconds, a start-up screen appears.
The following icon appears at the top right corner of
the screen.
When this icon disappears, the recorder is ready to
operate.
If the disc drive contains a disc, it takes a
little longer to start up.
Viewing TV channels through this recorder
After turning the power on, the recorder will output TV
channel signals to the connected TV (also in the stop
mode).
You can select a desired channel by pressing the
CHANNEL or the number buttons.
(These buttons can select channels of a connected
cable box or satellite system, if
“
IR control
”
(
page
37, in
“
INSTALLATION GUIDE
”
) is set to
“
On
”
.)
Loading a disc
Check disc compatibility beforehand (
page 6, 7)
and use a proper playable disc.
Caution
•
Keep your fingers well clear of the disc tray. Neglecting this
may cause serious personal injury.
Keep a close watch on
children.
•
Do not use a cracked, deformed, or repaired disc.
1
Open the disc tray.
Press
on the front panel or the OPEN/CLOSE
button on the remote control.
2
Insert a disc.
Disc without a cartridge
Insert with the playback side down.
There are two kinds of disc size. Place a disc to fit
the guide. If a disc is out of the guide, it may result
in damage to the disc or malfunction.
Place a disc in the
inside hollow.
Introduction
Before operating this recorder
ON/STANDBY button
CHANNEL buttons
ON/STANDBY button
ON/STANDBY indicator
OPEN/CLOSE button
button
Loading
e.g.