Uniden DXAI8580-2 English Owners Manual - Page 5

Using the handset menu • To open the handset menu, press and hold [cid/menu] for two seconds. • The arrow pointer on the left side of the line shows which menu item is currently highlighted. Use [ / ] to move the pointer up and [ ] to move the pointer down. • If the phone beeps and stays on the same line, it means you have reached the top or bottom of the list. • Press [select/channel] to rotate through the available options for the highlighted menu item. • Press [END] to exit the menu. Note: You can find detailed information on the handset menu in section 3 on Setting Up Your Phone and section 4 on Using Your Phone. Ringer :Type A Ring. Vol.:High Auto Talk :Off CIDCW :On Area Code : Dial :Tone Language :Eng (HS1 display) 2-4. Parts of the Base Speaker Message counter LED menu/clock key set key vol/select/ key (volume/select/up) vol/select/ key (volume/select/down) charge/in use LED key (delete) key (skip) key (play/stop) Charging contacts key (repeat) key (answering sysytem on/off) greet key memo key ringer key find hs key Note: For information on the base menu, see section 7 on Using Your Answering system. 3) Setting Up Your Phone Your phone has four basic options that you need to set up first. You should only have to set these options once, and you may not have to change any of them: • Dial mode (tone or pulse dialing) • CIDCW (Caller ID on Call Waiting) • Language • Auto talk You might change two handset-specific options --ringer type and ringer volume -- and one base setting - ringer volume --more often, depending on the situation. There's another option, area code, that you should only set if you can use seven-digit dialing (see section 5-3 on Using Seven Digits Instead of Ten). 3-1. System Options (from HS1 only) These options can only be changed from handset 1 (HS1). After changing these settings, you must put HS 1 back in the base cradle to activate them. Changing from tone to pulse dialing (DIAL) Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most phone networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you need to change your phone's dial settings. If you don't get a dial tone or can't connect to the telephone network, follow the steps below to modify your phone's settings: 1) Make sure you have Handset 1 (HS 1). 2) With the phone in standby, press and hold [cid/menu]. 3) Press [ ] to move the pointer to DIAL. 4) Press [select/channel] to set the phone to pulse dialing. 5) Press [END] and put the handset back in the base. Handset 1 communicates the new setting to the base, and the base activates the setting on any other handsets. Note: If you use pulse dialing and you need to send DTMF tones during a call (if you're using an automated response system, for example), press [ /tone/ ] to temporarily switch to tone dialing. When the call ends, the phone automatically returns to pulse dialing mode. Activating Caller ID on Call Waiting (CIDCW) You must subscribe to Caller ID service through your local telephone provider to use this feature. Caller ID allows you to see the name and number of the calling party before you answer the phone. Caller ID on Call Waiting (CIDCW) lets you see the name and number of a call that comes in when you are on the line. 1) Make sure you have Handset 1 (HS 1). 2) With the phone in standby, press and hold [cid/menu]. 3) Press [ ] to move the pointer to CIDCW. 4) Press [select/channel] to toggle and turn on Caller ID on Call Waiting. 5) Press [END] and put the handset back in the base. Handset 1 communicates the new setting to the base, and the base activates the setting on any other handsets. 3-2. Handset-specific Options These options can be set differently on each handset. You can also set these options while another handset is using the phone. Setting the display language (LANGUAGE) The handset menus can use English (ENG, default), French (FR) or Spanish (ESP). 1) With the phone in standby, press and hold [cid/menu]. 2) Press [ ] to move the pointer to LANGUAGE. 3) Press [select/channel] to select ENG, FR. or ESP. 4) When the display shows the language you want, use [ / ] and [ ] to move the pointer to another menu item. OR If you're finished, press [END] to return the handset to standby. Note: To change the language used by the answering system, see Section 7-1 on Setting Up the Answering System.