Uniden SC150Y English Owners Manual - Page 17

Scanning, u

Get Uniden SC150Y PDF manuals and user guides View all Uniden SC150Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Scanning Note: When you turn the scanner on it will be in the same Mode it was in when you turned it off. Bank Scanning B 1. Look at the upper left corner of the display. If BANK is not displayed, press . S 2. If SCN is not displayed in the lower left corner of the display, press . The SportCat should begin scanning. H S 3. If HOLD appears at the bottom of the display, press or to begin scanning. The indicators for the selected Banks (1 through 10) appear on the display. The indicator of the Bank currently being monitored flashes. While the SportCat is scanning, the word SCAN moves across the display. Scanning stops on any active channel that is not "Locked Out", and displays the Channel Number and frequency. Scanning resumes automatically after the transmission stops. 4. You can deselect any bank(s) from being scanned by entering the number of the bank. The deselected bank indicator(s) disappear from the display, and those channels will not be scanned. This procedure helps to speed up the scanning cycle. Note: One Bank must always be active. You cannot deactivate all 10 banks at the same time. If you try to deactivate all 10 Banks, Bank 1 will automatically be active. 5. To restore any bank for scanning, just enter its number again. The bank indicator will reappear on the display. H 6. To stop scanning any time, press . (HOLD appears on the display.) The scanner remains on H S the displayed channel, and only the bank indicator for that channel appears. Press again or , to resume scanning. 7. When you are stopped at a channel, you can press d to step down a channel, or u to step up a channel. Press and hold either key to rapidly step through the channels. Note: You do not skip a locked out ("L/O") channel when you use d or u or GO TO. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
Scanning
Note:
When you turn the scanner on it will be in the
same Mode it was in when you turned it off.
Bank Scanning
1.
Look at the upper left corner of the display. If
BANK
is not displayed, press
B
.
2.
If
SCN
is not displayed in the lower left corner of the
display, press
S
. The SportCat should begin
scanning.
3.
If
HOLD
appears at the bottom of the display, press
H
or
S
to begin scanning.
The indicators for the selected Banks (
1
through
10
) appear
on the display. The indicator of the Bank currently being
monitored flashes. While the SportCat is scanning, the
word
SCAN
moves across the display.
Scanning stops on any active channel that is not “Locked
Out”, and displays the Channel Number and frequency.
Scanning resumes automatically after the transmission stops.
4.
You can deselect any bank(s) from being scanned
by entering the number of the bank. The deselected
bank indicator(s) disappear from the display, and
those channels will not be scanned. This procedure
helps to speed up the scanning cycle.
Note:
One Bank must always be active. You cannot
deactivate all 10 banks at the same time. If you try to
deactivate all 10 Banks, Bank 1 will automatically be
active.
5.
To restore any bank for scanning, just enter its
number again. The bank indicator will reappear on
the display.
6.
To stop scanning any time, press
H
.(
HOLD
appears on the display.) The scanner remains on
the displayed channel, and only the bank indicator
for that channel appears. Press
H
again or
S
,
to resume scanning.
7.
When you are stopped at a channel, you can press
d
to step down a channel, or
u
to step up a channel.
Press and hold either key to rapidly step through the
channels.
Note:
You do not skip a locked out (“
L/O
”) channel when
you use
d
or
u
or GO TO.
17