ViewSonic PA503W PA503S User Guide English - Page 22

Operation, Starting up the projector

Get ViewSonic PA503W PDF manuals and user guides View all ViewSonic PA503W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 2. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 31 for details. 3. If the projector is activated for the first time, select your OSD language following the on-screen instructions. 4. Switch all of the connected equipment on. 5. The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found. You can also press Source to select your desired input signal. See "Switching input signal" on page 21 for details. If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 61 for details. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
17
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
2.
Press
Power
to start the projector. As soon as
the lamp lights up, a "Power On Ring Tone" will
be heard. The
Power indicator light
stays blue
when the projector is on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning
it off.
To turn off the ring tone, see
"Turning off the Power On/Off Ring Tone" on page 31
for details.
3.
If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4.
Switch all of the connected equipment on.
5.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message '
No Signal
' will continue to be displayed until an input
signal is found.
You can also press
Source
to select your desired input signal. See
"Switching input
signal" on page 21
for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See
"Timing chart" on page 61
for details.