ViewSonic PG707X - 4000 Lumens XGA Networkable Projector with 1.3x Optical Zoom - Page 14

Remote Control Effective Range, Replacing the Remote Control Batteries

Get ViewSonic PG707X - 4000 Lumens XGA Networkable Projector with 1.3x Optical Zoom and Low Input Lag PDF manuals and user guides View all ViewSonic PG707X - 4000 Lumens XGA Networkable Projector with 1.3x Optical Zoom and Low Input Lag manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Remote Control Effective Range To ensure proper function of the remote control follow the steps below: 1. The remote control must be held at an angle within 30° perpendicular to the projector's IR remote control sensor(s). 2. The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.) NOTE: Refer to the illustration for the location of the infrared (IR) remote control sensor(s). Approx. 30° Replacing the Remote Control Batteries 1. Remove the battery cover from the rear of the remote control by pressing the finger grip and sliding it down. 2. Remove any existing batteries (if necessary) and install two AAA batteries. NOTE: Observe the battery's polarities as indicated. 3. Replace the battery cover by aligning it with the base and pushing it back into position. NOTE: • Avoid leaving the remote control and batteries in excessive heat or a humid environment. • Replace only with the same or equivalent type recommended by the battery manufacturer. • Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
14
Remote Control Effective Range
To ensure proper function of the remote control
follow the steps below:
1.
The remote control must be held at an angle
within 30° perpendicular to the projector’s IR
remote control sensor(s).
2.
The distance between the remote control and
the sensor(s) should not exceed 8 m (26 ft.)
NOTE:
Refer to the illustration for the location of
the infrared (IR) remote control sensor(s).
Approx. 30°
Replacing the Remote Control Batteries
1.
Remove the battery cover from the rear of the remote control by pressing the
finger grip and sliding it down.
2.
Remove any existing batteries (if necessary) and install two AAA batteries.
NOTE:
Observe the battery’s polarities as indicated.
3.
Replace the battery cover by aligning it with the base and pushing it back into
position.
NOTE:
•
Avoid leaving the remote control and batteries in excessive heat or a humid
environment.
•
Replace only with the same or equivalent type recommended by the battery
manufacturer.
•
Dispose of the used batteries according to the manufacturer’s instructions and
local environment regulations for your region.
•
If the batteries are drained or if you will not be using the remote control for an
extended period of time, remove the batteries to avoid damage to the remote
control.