Home » ViewSonic Manuals » Projectors » ViewSonic PJD6381 » Manual Viewer

ViewSonic PJD6381 PJD6381 User Guide (English) - Page 24

Computer Image Computer Mode, Video Image Video Mode, Sound Computer / Video Mode, Setting Computer - 3d

UPC - 766907342611

Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Gamma Effect the represent of dark scenery. With greater gamma value, dark scenery will look brighter. 3D Sync „ On: 120Hz detection „ Off: Disable 120Hz 3D Sync Invert „ On: Invert left and right frame contents. „ Off: Default frame contents. Computer Image (Computer Mode) Frequency Adjust the timing of the projector relative to the computer. Tracking Adjust the phase of the projector relative to the computer. H Position (Horizontal Position) Adjust the image left or right within the projection area. V Position (Vertical Position) Adjust the image up or down within the projection area. Video Image (Video Mode) Saturation Adjust a video image from black and white to fully saturated color. Sharpness Sharpen or soften the image. Tint Shift colors toward red or green. Sound (Computer / Video Mode) Volume Adjust the volume level. Mute Cut off the sound temporarily. Audio 1 Enable or disable Audio 1. „ When Audio 1 is turned on, Audio 2 will turn off automatically. Audio 2 Enable or disable Audio 2. „ When Audio 2 is turned on, Audio 1 will turn off automatically. Setting (Computer / Video Mode) EN-21

Section	Page
VPD-X5501-EN.pdf	6
Introduction	8
Projector Features	8
Package Contents	9
Projector with Lens Cap	9
AC Power Cord	9
Projector Overview	10
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	14
Installing the Batteries	15
1. Open the battery cover in the direction shown.	15
2. Install batteries as indicated by the diagram inside the compartment.	15
3. Close the battery cover into position.	15
Remote Control Operation	16
Installation	17
Connecting the Projector	17
Powering On/Off the Projector	18
Powering On the Projector:	18
1. Remove the projector lens cap.	18
2. Complete the AC power cord and peripheral signal cable(s) connections.	18
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	18
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	18
Powering Off the Projector:	18
1. Press button to turn off the projector lamp. You will see a message \	18
2. Press button again to confirm.	18
3. Disconnect the AC power cord from the electrical outlet and the projector.	18
4. Do not turn on the projector right after power off.	18
Adjusting the Projector	19
Adjusting the Projector Height	19
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	19
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	19
Adjusting the Projector Focus	19
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	19
Adjusting Projection Image Size	20
Menu Operation	21
1. Press the MENU button to open the OSD menu.	23
2. When OSD is displayed, use p / q to select any feature in the main menu.	23
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.	23
4. Use p / q to select the desired item and adjust the settings with t / u.	23
5. Press the MENU button, the screen will return to the main menu.	23
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	23
Network Control	28
1. Connect one end of the internet cable to the Network Control connector on the projector.	28
2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.	28
3. Turn on your projector and computer.	28
1. Enable DHCP from the projector OSD, under Network Config.	28
2. Start browser in PC and specify following URL, then click “Go” button.	29
3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.	29
1. Set IP Address and Subnet Mask under Network Config.	30
2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..	30
3. Select \	31
4. Set your PC’s IP address, and click OK.	31
5. Start browser in PC and specify following URL, then click “Go” button.	32
6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.	32
1. Go to Tools > General and click \	41
2. Click \	42
3. Click \	42
Maintenance	43
Cleaning the Lens	43
Cleaning the Projector Housing	43
Cleaning the Filter Cover	43
1. Switch the projector off and unplug the AC power cord from the wall socket.	43
2. Remove the filter cover as the illustration shown.	43
3. Clean the filter cover.	43
4. Replace the filter cover.	43
5. Attach the filter cover.	43
6. Plug the power back into the projector.	43
Replacing the Lamp	44
1. Turn off the projector.	45
2. If the projector is installed in a ceiling mount, remove it	45
3. Unplug the power cord.	45
4. Loosen the screw in the side of the lamp cover and remove the cover.	45
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	45
6. Insert the new lamp module into the projector and tighten the screws.	45
7. Replace the lamp cover and tighten the screw.	45
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	45
9. Reset the lamp hour. Refer to the “Setting” menu.	45
Specifications	46
Appendix	47
LED Indicator Messages	47
Compatibility Modes	48
Computer:	48
Video:	49
Troubleshooting	50
Start-up problems	50
Image problems	50
RS-232 Command and Configuration	51