Home » ViewSonic Manuals » Projectors » ViewSonic PJD6381 » Manual Viewer

ViewSonic PJD6381 PJD6381 User Guide (English) - Page 47

Appendix

UPC - 766907342611

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Appendix LED Indicator Messages LED Type Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Color Blue Off Off Blue Off Off Blue Off Off Blue Off Off Blue Red Red Blue Off Off Blue Off Off Status Solid (LED x 1) Off Off Solid (LED x 2) Off Off Solid (LED x 2) Off Off Flash (LED x 2) Off Off Solid (Full brightness) Solid Flash Solid (Full brightness) Off Off Solid (Full brightness) Solid Solid Power LED Lamp LED Temp LED Blue Red Red Flash (Full brightness) Solid Solid Power LED Lamp LED Temp LED Power LED Lamp LED Temp LED Blue Red Red Off Red Red Solid (Full brightness) Flash Off Off Solid Solid Meaning The projector is in standby mode. Powering up Normal operation Power-down The projector system has some problems with its fans, so the projector cannot start up. The lamp is in good condition and is projecting at maximum brightness. The lamp has reached its end of life and must be changed soon. The lamp will continue to operate until it fails . Change the lamp. If the lamp is off, then the ballast will become malfunction. The projector is shutting and the fan motor is cooling the lamp for shutdown. Do not unplug the power cord or turn the power off before the Lamp LED changes to flashing. The fan motor will turn off when the lamp has cooled. Temperature is too high. The lamp will turn off. The fan motor is cooling the lamp. The lamp ignition failed. If temperature is too high, the fans will cool the lamp. EN-44

Section	Page
VPD-X5501-EN.pdf	6
Introduction	8
Projector Features	8
Package Contents	9
Projector with Lens Cap	9
AC Power Cord	9
Projector Overview	10
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	14
Installing the Batteries	15
1. Open the battery cover in the direction shown.	15
2. Install batteries as indicated by the diagram inside the compartment.	15
3. Close the battery cover into position.	15
Remote Control Operation	16
Installation	17
Connecting the Projector	17
Powering On/Off the Projector	18
Powering On the Projector:	18
1. Remove the projector lens cap.	18
2. Complete the AC power cord and peripheral signal cable(s) connections.	18
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	18
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	18
Powering Off the Projector:	18
1. Press button to turn off the projector lamp. You will see a message \	18
2. Press button again to confirm.	18
3. Disconnect the AC power cord from the electrical outlet and the projector.	18
4. Do not turn on the projector right after power off.	18
Adjusting the Projector	19
Adjusting the Projector Height	19
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	19
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	19
Adjusting the Projector Focus	19
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	19
Adjusting Projection Image Size	20
Menu Operation	21
1. Press the MENU button to open the OSD menu.	23
2. When OSD is displayed, use p / q to select any feature in the main menu.	23
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.	23
4. Use p / q to select the desired item and adjust the settings with t / u.	23
5. Press the MENU button, the screen will return to the main menu.	23
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	23
Network Control	28
1. Connect one end of the internet cable to the Network Control connector on the projector.	28
2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.	28
3. Turn on your projector and computer.	28
1. Enable DHCP from the projector OSD, under Network Config.	28
2. Start browser in PC and specify following URL, then click “Go” button.	29
3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.	29
1. Set IP Address and Subnet Mask under Network Config.	30
2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..	30
3. Select \	31
4. Set your PC’s IP address, and click OK.	31
5. Start browser in PC and specify following URL, then click “Go” button.	32
6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.	32
1. Go to Tools > General and click \	41
2. Click \	42
3. Click \	42
Maintenance	43
Cleaning the Lens	43
Cleaning the Projector Housing	43
Cleaning the Filter Cover	43
1. Switch the projector off and unplug the AC power cord from the wall socket.	43
2. Remove the filter cover as the illustration shown.	43
3. Clean the filter cover.	43
4. Replace the filter cover.	43
5. Attach the filter cover.	43
6. Plug the power back into the projector.	43
Replacing the Lamp	44
1. Turn off the projector.	45
2. If the projector is installed in a ceiling mount, remove it	45
3. Unplug the power cord.	45
4. Loosen the screw in the side of the lamp cover and remove the cover.	45
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	45
6. Insert the new lamp module into the projector and tighten the screws.	45
7. Replace the lamp cover and tighten the screw.	45
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	45
9. Reset the lamp hour. Refer to the “Setting” menu.	45
Specifications	46
Appendix	47
LED Indicator Messages	47
Compatibility Modes	48
Computer:	48
Video:	49
Troubleshooting	50
Start-up problems	50
Image problems	50
RS-232 Command and Configuration	51

Match case Limit results 1 per page

EN-44

Appendix

LED Indicator Messages

LED Type

Color

Status

Meaning

Power

LED

Blue

Solid (LED x 1)

The projector is

in standby

mode.

Lamp LED

Off

Temp LED

Off

Power

LED

Blue

Solid (LED x 2)

Powering up

Lamp LED

Off

Temp LED

Off

Power

LED

Blue

Solid (LED x 2)

Normal operation

Lamp LED

Off

Temp LED

Off

Power

LED

Blue

Flash (LED x 2)

Power-down

Lamp LED

Off

Temp LED

Off

Power

LED

Blue

Solid (Full brightness)

The projector system has some

problems with its fans, so the

projector cannot start up.

Lamp LED

Red

Solid

Temp LED

Red

Flash

Power

LED

Blue

Solid (Full brightness)

The lamp is in good condition

and is projecting at maximum

brightness.

Lamp LED

Off

Temp LED

Off

Power

LED

Blue

Solid (Full brightness)

The lamp has reached its end

of life and must be changed

soon. The lamp will continue to

operate until it fails . Change

the lamp. If the lamp is off, then

the ballast will become

malfunction.

Lamp LED

Off

Solid

Temp LED

Off

Solid

Power

LED

Blue

Flash

(Full

brightness)

The projector is shutting and

the fan motor is cooling the

lamp for shutdown. Do not

unplug the power cord or turn

the power off before the Lamp

LED changes to flashing. The

fan motor will turn off when the

lamp has cooled.

Lamp LED

Red

Solid

Temp LED

Red

Solid

Power

LED

Blue

Solid (Full brightness)

Temperature is too high. The

lamp will turn off. The fan motor

is cooling the lamp.

Lamp LED

Red

Flash

Temp LED

Red

Off

Power

LED

Off

The lamp ignition failed. If

temperature is too high, the

fans will cool the lamp.

Lamp LED

Red

Solid

Temp LED

Red

Solid