ViewSonic Pro8300 PRO8300 User Guide - Page 22

Connecting a Component Video source device, Connecting an S-Video source device - color settings

Get ViewSonic Pro8300 PDF manuals and user guides View all ViewSonic Pro8300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a Component Video to VGA (D-Sub) adaptor and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red. 2. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video to VGA (D-Sub) adaptor, connect the other end of the cable (with a D-Sub type connector) to the Computer in 1 or Computer in 2 socket on the projector. If you are using the Component Video Cable, connect the other end of 3RCA type connectors to the Y Cb/ Pb Cr/Pr sockets on the projector. Important • If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly. • RGB to component adapter (ViewSonic P/N: J2552-0212-00) Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2. Connect the other end of the S-Video cable to the S-Video socket on the projector. Important • If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
15
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
•
If so, you can continue with this procedure.
•
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a Component
Video to VGA (D-Sub) adaptor and connect the end with 3 RCA type connectors to the
Component Video output sockets of the Video source device. Match the color of the
plugs to the color of the sockets; green to green, blue to blue, and red to red.
2.
If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video to
VGA (D-Sub) adaptor, connect the other end of the cable (with a D-Sub type connector)
to the
Computer in 1
or
Computer in 2
socket on the projector. If you are using the
Component Video Cable, connect the other end of 3RCA type connectors to the
Y Cb/
Pb Cr/Pr
sockets on the projector.
Important
•
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
•
RGB to component adapter (ViewSonic P/N: J2552-0212-00)
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
•
If so, you can continue with this procedure.
•
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2.
Connect the other end of the S-Video cable to the
S-Video
socket on the projector.
Important
•
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.