Vtech TL7600 User Manual - Page 12

To register the headset to an AT&T DECT cordless telephone, ON/OFF, HANDSET, LOCATOR, IN USE

Get Vtech TL7600 PDF manuals and user guides View all Vtech TL7600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Getting started Registering the headset To register the headset to an AT&T DECT cordless telephone base: 1. Make sure the battery is properly installed in the headset (see page 3). The ON/OFF light flashes twice every five seconds to indicate the headset is not registered. 2. Place the headset in the headset charger and allow it to charge for at least five minutes before beginning registration. Remove the headset from the charger and replace the headset back into the charger. 3. On the telephone base of the cordless phone, press and hold the HANDSET LOCATOR button until the IN USE light comes on (about four seconds) and release the button. 4. The headset registers to the telephone base automatically; this may take about 30 seconds to complete. The IN USE light on the telephone base turns off. The headset ON/OFF light turns blue on the first headset registered. The headset ON/OFF light turns orange on the second headset registered. To verify registration was successful, press the headset ON/OFF button and check for a dial tone. NOTE: If the registration is not successful, the ON/OFF light on the headset flashes twice every five seconds. Reset the headset and try again. Remove the headset from the charger and press ON/OFF. Then place the headset back into the headset charger. Try the registration process again. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
7
Getting started
Registering the headset
To register the headset to an AT&T DECT cordless telephone
base:
Make sure the battery is properly installed
in the headset (see page 3). The
ON/OFF
light flashes twice every five seconds to
indicate the headset is not registered.
Place the headset in the headset charger
and allow it to charge for at least five
minutes before beginning registration.
Remove the headset from the charger
and replace the headset back into the
charger.
On the telephone base of the cordless
phone, press and hold the
HANDSET
LOCATOR
button until the
IN USE
light
comes on (about four seconds) and release
the button.
The headset registers to the telephone
base automatically; this may take about
30 seconds to complete. The
IN USE
light on the telephone base turns off.
The headset
ON/OFF
light turns blue on
the first headset registered. The headset
ON/OFF
light turns orange on the second
headset registered. To verify registration
was successful, press the headset
ON/
OFF
button and check for a dial tone.
NOTE:
If the registration is not successful, the
ON/OFF
light on the headset
flashes twice every five seconds. Reset the headset and try again. Remove the
headset from the charger and press
ON/OFF
. Then place the headset back into
the headset charger. Try the registration process again.
1.
2.
3.
4.