Vtech TL7610 User Manual - Page 30

To deregister all headsets from the headset base, To deregister all headsets from an AT&T - at t manual

Get Vtech TL7610 PDF manuals and user guides View all Vtech TL7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Deregistration Replacing a headset To deregister all headsets from the headset base NOTES: 1. If the deregistration process was not successful, you may need to reset the system and try again. Remove the headset from the headset base and press ON/OFF. Place the headset back into the headset base. You may also reset by unplugging the power from the headset base, then wait a few seconds, and plug it back in. 2. You cannot deregister the headset(s) if another system headset is in use. To deregister all headset(s) from an AT&T cordless telephone base This procedure deregisters all the headset(s) and handset(s) registered to the cordless phone. 1. Press and hold � HANDSET LOCATOR �o�n��th��e��te�l�e�p�h��o�n�e��b�a�s�e� of the cordless phone until the IN USE light on the telephone base turns on and starts to flash (at least 10 seconds), then release the HANDSET LOCATOR button. 2. Immediately press and release HANDSET LOCATOR again. You must press HANDSET LOCATOR while the IN USE light is still flashing. (The light flashes for about seven seconds. If the light stops flashing, start again with step one above.) 3. Deregistration may take up to 10 seconds to complete. The ON/OFF light on the headset flashes twice every five seconds if deregistration was successful. NOTES: 1. See your telephone user's manual to register the handsets again. 2. See page 7 of this manual to register a headset again. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
26
Deregistration
Replacing a headset
To deregister all headsets from the headset base
NOTES:
1. If the deregistration process was not successful, you may need to reset the system
and try again. Remove the headset from the headset base and press
ON/OFF
.
Place the headset back into the headset base. You may also reset by unplugging
the power from the headset base, then wait a few seconds, and plug it back in.
2. You cannot deregister the headset(s) if another system headset is in use.
To deregister all headset(s) from an AT&T cordless telephone base
This procedure deregisters all the headset(s) and handset(s)
registered to the cordless phone.
Press and hold
HANDSET LOCATOR
on the telephone base
on the telephone base
of the cordless phone until the
IN USE
light on the telephone
base turns on and starts to flash (at least 10 seconds), then
release the
HANDSET LOCATOR
button.
Immediately press and release
HANDSET LOCATOR
again.
You must press
HANDSET LOCATOR
while the
IN USE
light
is still flashing. (The light flashes for about seven seconds. If
the light stops flashing, start again with step one above.)
Deregistration may take up to 10 seconds to complete. The
ON/OFF
light on the headset flashes twice every five seconds
if deregistration was successful.
NOTES:
See your telephone user’s manual to register the handsets again.
See page 7 of this manual to register a headset again.
1.
2.
3.
1.
2.