Vtech t2406 User Manual

Vtech t2406 - 2.4 GHz Analog Cordless Phone Manual

Get Vtech t2406 - 2.4 GHz Analog Cordless Phone PDF manuals and user guides
UPC - 735078006011
View all Vtech t2406 manuals
Add to My Manuals
Save this manual to your list of manuals

Vtech t2406 manual content summary:

  • Vtech t2406 | User Manual - Page 1
    instructions. 2. Follow all warnings and instructions marked If service or repair work is required, contact VTech Customer Service at using a telephone (other than a cordless type) during an electrical storm. There phone to the store. Call our Customer Support Center at: 1-800-595-9511 In Canada,
  • Vtech t2406 | User Manual - Page 2
    Introduction Parts Check List: 1. Handset 2. Base Unit 3. Telephone Line Cord 4. Battery Pack 5. AC Adapter 6. User's Manual To purchase replacement battery packs, call VTech Communications at 1-800-5959511. In Canada, call VTech Electronics at 1-800-267-7377. USER’S MANUAL 2
  • Vtech t2406 | User Manual - Page 3
    Handset and Base Layout 1 2 1 3 4 8 5 11 6 9 12 7 10 1. Antenna 2. Earpiece 3. IN USE/LOW BATT LED 4. PHONE(FLASH) 5. Dialing Keys (0-9,*, #) 6. MEM(PROG) 7. Channel 8. OFF 9. REDIAL(PAUSE) 10. Volume 11. PAGE 12. IN USE/CHARGING LED 3
  • Vtech t2406 | User Manual - Page 4
    pack down, so it is held in place by the lower claw. Now, plug the connector into the socket. Slip the battery wires into the guide, located below the battery. 3. Replace the battery cover by sliding it upwards. 4. Place the Handset in the Base Unit, and 2 allow it to charge for 12 hours
  • Vtech t2406 | User Manual - Page 5
    After the battery pack is charged, pick up the Handset and press the PHONE key. The IN USE indicator should light up, and you should hear a dial tone; if not, see IN CASE OF DIFFICULTY. Tone/Pulse Selection See OPERATING INSTRUCTIONS for details. CAUTION: Use only the VTech power supply provided
  • Vtech t2406 | User Manual - Page 6
    with an incoming ring. • It flashes quickly during programming mode. • It flashes slowly when battery is low. PHONE / FLASH KEY • Press the PHONE key to make a call. • If you are currently on a call, pressing PHONE flashes the line. This would be used with call waiting to answer your second call
  • Vtech t2406 | User Manual - Page 7
    KEY IN USE /CHARGING IN USE/CHARGING LED • The LED illuminates steadily when the Handset is in the Base cradle to indicate that the Handset battery is being charged. • The LED illuminates whenever the Handset is being used. • This LED also flashes in cadence with the incoming ring. PAGE KEY • Press
  • Vtech t2406 | User Manual - Page 8
    Operating Instructions Making Calls • Pick up the Handset and press PHONE. • When you hear a dial tone, dial the number. • The IN USE LED will illuminate while the Handset is on a call. If you make a mistake when dialing, press OFF to hang up, then press PHONE to get the dial tone again. • You must
  • Vtech t2406 | User Manual - Page 9
    will send the proper signals. • To end the call, press OFF or place the Handset back in the Base. The phone will automatically go back to rotary (dial-pulse) service. Programming the Ringer Type The Handset ringer is capable of four different types of ringing tones. To select a different ringer
  • Vtech t2406 | User Manual - Page 10
    be up to 16 digits long. The number can be entered manually or by using REDIAL. • Press MEM/PROG to store the phone number to the key you selected. The phone exits programming mode and emits a series of beeps. Speed Number Dialing • Press PHONE to get a dial tone. • Press MEM/PROG and the memory
  • Vtech t2406 | User Manual - Page 11
    Operating Instructions Storing Pauses in Memory • To insert a pause in a phone number, press REDIAL/PAUSE. The pause is 2 seconds in length. For longer pauses, press REDIAL/PAUSE two or more times. Each additional press adds an additional 2 seconds pause. • If your phone is connected to a PBX you
  • Vtech t2406 | User Manual - Page 12
    Maintenance Taking Care Of Your Telephone Your t 2406 cordless telephone contains sophisticated electronic parts, so it must be treated with care. Avoid rough treatment Place the Handset down gently. Save the original packing materials
  • Vtech t2406 | User Manual - Page 13
    the battery pack needs charging. No Dial Tone • First check all the suggestions above. • If you still don't hear a dial tone, disconnect the Base Unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service
  • Vtech t2406 | User Manual - Page 14
    , do the following(in the order listed) : 1. Disconnect the power to the Base. 2. Disconnect the Handset battery. 3. Wait a few minutes. 4. Connect power to the Base. 5. Re-install the battery pack, and return the Handset to the charge cradle. 6. After a few seconds, try using your Handset again
  • Vtech t2406 | User Manual - Page 15
    , when installed and used normally and in accordance with operation instructions. This limited warranty extends only to the Consumer for Products by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions
  • Vtech t2406 | User Manual - Page 16
    service? • To obtain warranty service in the United States of America, call 1-800-595-9511 for instructions regarding where to return the Product. Before calling for service, please check the user's manual not meet the terms of this limited warranty, VTech will notify you and will request that you
  • Vtech t2406 | User Manual - Page 17
    do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. • In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the
  • Vtech t2406 | User Manual - Page 18
    trouble with this telephone equipment, please contact: VTech Communications Inc. CUSTOMER SERVICE at 1-800-595-9511. In Canada, call VTech Electronics energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
  • Vtech t2406 | User Manual - Page 19
    single line and an RJ14 jack for two lines. See Installation Instructions in the user's manual. This equipment may not be used with Coin Telephone Lines or service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem
  • Vtech t2406 | User Manual - Page 20
    this product is equipped with a corded or cordless handset, it is hearing aid compatible. 6. so that you can still dial the emergency number manually if the memory dialing feature doesn't work. b. the early morning or late evening, when the emergency services tend to be less busy. IC (Industry Canada
  • Vtech t2406 | User Manual - Page 21
    electrical inspection authority, or electrician, as appropriate. Your Cordless Phone is designed to operate at the maximum power allowed by VTech product service centers. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery recycling and disposal bans/restrictions in your area. VTech
  • Vtech t2406 | User Manual - Page 22
    .10 MHz RECEIVE FREQUENCY Base: 912.75-917.10 MHz Handset: 2410.2-2418.9 MHz CHANNELS 30 Channels POWER REQUIREMENTS Handset: 3.6V 400mAh Ni-Cd Battery Pack Base : 9V DC @ 300mA MEMORY Speed Dial: 10 Memory locations 16 digits per location NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC and
  • Vtech t2406 | User Manual - Page 23
    GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications Inc.; Beaverton, Oregon. Distributed in Canada by VTech Electronics Canada Ltd., Suite 200, 7671 Alderbridge Way, Richmond, B.C. V6X 1Z9. Copyright 2003 for VTECH TELECOMMUNICATIONS LTD. Printed in China 91-5392-10-00 ISSUE 0
  • Vtech t2406 | User Manual - Page 24
    ANY KEY ANSWER 30 CHANNEL OPERATION 2406 UNIQUE STAND UP DESIGN USER'S MANUAL VTECH TELECOMMUNICATIONS LTD. www.vtechphones.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
1
When using your telephone equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or
swimming pool).
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To
protect it from overheating, these openings must not be blocked by placing the product
on the bed, sofa, rug, or other similar surface.
This product should never be placed near
or over a radiator or heat register. This product should not be placed in a built-in-
installation where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your
dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord
will be abused by persons walking on it.
9. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product. If service or repair
work is required, contact
VTech
Customer Service at
1-800-595-9511
.
Opening or
removing cabinet parts other than specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause electric shock when the appliance
is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or
electric shock.
12. Unplug this product from the wall outlet:
a)
When the power supply cord or plug is damaged or frayed.
b)
If liquid has been spilled into the product.
c)
If the product has been exposed to rain or water.
d)
If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions because improper
adjustment of other controls may result in damage and will often require extensive work
to restore the product to normal operation.
e)
If the product has been dropped and the cabinet has been damaged.
f)
If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote
risk of electric shock from lighting.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
If you have questions about this product, or if you're
having difficulty with setup or operation, do not return
your phone to the store. Call our Customer Support
Center at:
1-800-595-9511
In Canada, call
1-800-267-7377
Important Safety Instructions