Weber Summit 400 LP Operating Guide - Page 6

LIGHTING, Crossover Ignition System, TO EXTINGUISH

Get Weber Summit 400 LP PDF manuals and user guides View all Weber Summit 400 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

LIGHTING EACH HEAT ZONE OPERATES INDEPENDENTLY. Summary lighting instructions are on the control panel. High Medium Low Off Crossover Ignition System ƽ DANGER Failure to open sliding work surfaces while igniting the barbecue, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death. Note - The Crossover Ignition System ignites the Left burner of each Heat Zone with a spark from the igniter electrode inside the Gas Catcher Ignition Chamber. You generate the energy for the spark by pushing the Crossover Ignition Button until it clicks. ƽWARNING: Check hose before each use of barbecue for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, do not use the barbecue. Contact your dealer. Crossover Ignition System 1 4 3 2 Figure 1 1) Open the sliding work surfaces and splash guards. Figure 1. 2) Check that the fuel scale reads more than "E". Note - E = empty; F = full. 3) Make sure all burner control knobs are OFF. (Push each burner control knob down and turn clockwise.) ƽWARNING: The burner control knobs must be in the OFF position before turning on the LP tank valve. If they are not in the OFF position, when you turn on the LP tank valve, the excess flow control will activate, limiting the flow of gas from the LP tank. If this should occur, turn OFF the LP tank valve and burner control knobs and start over. ƽ DANGER When the excess flow control is activated, a small amount of gas is still flowing to the burners. After turning OFF the tank and burner control knobs, wait at least 5 minutes for the gas to clear before attempting to light the barbecue. Failure to do so may result in an explosive flameup which can cause serious bodily injury or death. 4) Turn the tank on by turning the tank valve counterclockwise. ƽWARNING: Do not lean over open barbecue. Keep your face and body at least one foot away from the matchlight hole when lighting the barbecue. 5) Select Heat Zone. 6) Push LEFT burner control knob down and turn to START/HI. 7) Push the Crossover Ignition Button several times, so it clicks each time. 8) Check that the burner is lit by looking through the matchlight hole above the burner control knob. ƽWARNING: If the burner does not light, turn the LEFT burner control knob to OFF and wait 5 minutes to let the gas clear before you try again or try to light with a match. 9) After the LEFT burner is lit you can turn on the RIGHT burner. Note - Always light the LEFT burner first. The RIGHT burner ignites from the LEFT burner. TO EXTINGUISH Turn gas supply OFF at the source, then push down and turn each burner control knob clockwise to OFF. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
6
EACH HEAT ZONE OPERATES INDEPENDENTLY.
Summary lighting instructions are on the control panel.
Figure 1
m
DANGER
Failure to open sliding work surfaces
while igniting the barbecue,
or not
waiting 5 minutes to allow the gas to clear
if the barbecue does not light, may result
in an explosive flame-up which can cause
serious bodily injury or death.
High
Medium
Low
Off
Crossover Ignition System
3
2
4
1
1)
Open the sliding work surfaces and splash guards.
Figure 1.
2)
Check that the fuel scale reads more than “E”.
Note - E = empty; F = full.
3)
Make sure all burner control knobs are OFF. (Push
each burner control knob down and turn clockwise.)
m
WARNING:The burner control knobs must be in the
OFF position before turning on the LP tank valve. If
they are not in the OFF position, when you turn on
the LP tank valve, the excess flow control will
activate, limiting the flow of gas from the LP tank. If
this should occur, turn OFF the LP tank valve and
burner control knobs and start over.
m
DANGER
When
the
excess
flow
control
is
activated, a small amount of gas is still
flowing to the burners. After turning OFF
the tank and burner control knobs, wait at
least 5 minutes for the gas to clear before
attempting to light the barbecue. Failure
to do so may result in an explosive flame-
up which can cause serious bodily injury
or death.
LIGHTING
Note - The Crossover Ignition System ignites the Left
burner of each Heat Zone with a spark from the igniter
electrode inside the Gas Catcher Ignition Chamber.You
generate the energy for the spark by pushing the
Crossover Ignition Button until it clicks.
m
WARNING: Check hose before each use of
barbecue for nicks, cracking, abrasions or cuts. If the
hose is found to be damaged in any way, do not use
the barbecue. Contact your dealer.
Crossover Ignition System
4)
Turn the tank on by turning the tank valve
counterclockwise.
m
WARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
5)
Select Heat Zone.
6)
Push LEFT burner control knob down and turn to
START/HI.
7)
Push the Crossover Ignition Button several times, so
it clicks each time.
8)
Check that the burner is lit by looking through the
matchlight hole above the burner control knob.
m
WARNING: If the burner does not light, turn the
LEFT burner control knob to OFF and wait 5 minutes
to let the gas clear before you try again or try to light
with a match.
9)
After the LEFT burner is lit you can turn on the
RIGHT burner.
Note - Always light the LEFT burner first. The RIGHT
burner ignites from the LEFT burner.
TO EXTINGUISH
Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.