Weider 8300 Hard Drive English Manual
Weider 8300 Hard Drive Manual
 |
View all Weider 8300 Hard Drive manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 8300 Hard Drive manual content summary:
- Weider 8300 Hard Drive | English Manual - Page 1
will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-225-0653 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION! Read all safety precautions and instructions in this owner's manual before using this equipment. Save this owner's manual for future reference. PATENT PENDING • • 0 0 - Weider 8300 Hard Drive | English Manual - Page 2
using the hard drive system. 1. Read all Instructions in this owner's manual and in the accompanying literature before using the hard drive system. Use the hard drive system only as described. 2. Use the hard drive system only on a level surface. Cover the floor beneath the hard drive system for - Weider 8300 Hard Drive | English Manual - Page 3
achieve the specific results you want. For your safety and benefit, read this manual carefully before using the WEIDER 8300 Hard Drive System. If you have additional questions, please call our Customer Service Department toll-free at 1-800-667-2140 Monday through Friday, 9 a.m. until 5 p.m. Eastern - Weider 8300 Hard Drive | English Manual - Page 4
the hard drive system, make sure that all parts are oriented as shown in the drawings. Tighten all nuts and bolts as you attach them, unless instructed to do otherwise. For help identifying the small parts used in assembly, refer to the PART IDENTIFICATION CHART accompanying this owner's manual. THE - Weider 8300 Hard Drive | English Manual - Page 5
20 7-102 20 15 4. Turn each of the eighteen 10 Lb. Weights (107) so the "Weider" logo is on top. Press a Weight 4 93 Sleeve (93) into the top of each Weight (93) into the top of the Weight. Pin Groove 93 "Weider Logo Slide the eighteen 10 Lb. Weights (107) onto the 17 Weight Upright (17). - Weider 8300 Hard Drive | English Manual - Page 6
6. With the help of a second person, attach the Side Guard (42) and the VKR Side Guard (46) to the 6 Side Guard Brackets (20) with four #8 x 1/2" Self-. Tapping Screws (102). 46 2 102 42 20 102 7. Press a 1 3/4" Inner Cap (29) into the Front Upright (19). Slide the Front Upright (19) onto the - Weider 8300 Hard Drive | English Manual - Page 7
8. Slide the Rear Upright (49) onto the two indicated 5/16" x 2 1/2" Carriage Bolts (1) in the Base (15). Attach the Rear Upright to the Base with two 5/16" Nylon Locknuts (4). Do not tighten the Nylon Locknuts yet. Attach the Large "U" Bracket (85) to the Weight Upright (17) with the 5/16" x 3/4" - Weider 8300 Hard Drive | English Manual - Page 8
11. Remove the 3/8" Nylon Locknut (63) from the indicated 3/8" x 2 3/4" Bolt (55). Do not remove the Bolt. Press a 1 3/4" Inner Cap (29) into the upper end of the VKR Upright (97). Slide the VKR Upright (97) onto the 3/8" x 2 3/4" Bolt (55) in the Front Upright (19) and the two 5/16" x 2 1/2" - Weider 8300 Hard Drive | English Manual - Page 9
14. Attach a VKR Armrest (80) to the Left VKR Arm (24) with two 1/4" x 2" Screws (82) and 1/4" Flat Washers (6). Attach the other VKR Armrest (80) to the Right VKR Arm (79) in the same manner. 14 80 80 6 82 15. Press a 1" Round Cap (43) into a Handle (47). Insert the Handle (47) into the Left VKR - Weider 8300 Hard Drive | English Manual - Page 10
18. Press two 1 3/4" Inner Caps (29) into the Press Arm (12). Press a 1" Round Cap (43) into each of the four remaining Handles (47). Insert a Handle (47) into the right side of the Press Arm (12). Attach the Handle to the Press Arm with a 5/161x 21/4" Bolt (23), two 5/16" Flat Washers (45), a 1/2" - Weider 8300 Hard Drive | English Manual - Page 11
22. Align the holes in the Small "U"-Bracket (21) with the indicated hole in the Front Upright (19). Attach the Small "U"-Bracket to the Front Upright with a 5/16" x 2 3/4" Bolt (122) and 5/16" Nylon Locknut (4). Align one of the three sets of holes in the Adjustment Bracket (22) with the indicated - Weider 8300 Hard Drive | English Manual - Page 12
26. Insert a 1/4" x 2 1/2" Screw (54) through the Side Guard "T" Bracket (61) and the Rear Upright (49) as shown. Tighten the 1/4" x 2 1/2" Screw (54) into the upper end of the Butterfly Backrest (41). Attach the lower end of the Butterfly Backrest (41) to the Rear Upright (49) with a 1/4" x 2 1/2" - Weider 8300 Hard Drive | English Manual - Page 13
29. Attach an Arm Bracket (124) to the Lett Butterfly 29 Arm (27) with a 3/8" x 3 1/4" Bolt (8) and 3/8" Nylock Nut (63). 63 OO Attach an Arm Bracket (124) to the Right Butterfly Arm (105) in the same manner. 105 .: 1 4 . 2 8 30. Extend the two Long Arm Shocks (90). Apply a liberal amount - Weider 8300 Hard Drive | English Manual - Page 14
on page 15 of this owner's manual. Before using the hard drive system, pull the ends of the cables a few times to make sure that the cables move smoothly over the pulleys. If the cables do not move smoothly, locate and correct the problem before using the hard drive system. Refer to the CABLING - Weider 8300 Hard Drive | English Manual - Page 15
ADJUSTMENT The instructions below describe how each part of the hard drive system can be adjusted. Refer to the EXERCISE GUIDE accompanying this owner's manual to see how the hard drive system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that - Weider 8300 Hard Drive | English Manual - Page 16
ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (33), the Press Seat (31) must be attached to the Front Upright (19) (see ATTACHING AND REMOVING THE PRESS SEAT on page 15). Attach one end of the Chain (73) to the Pulley Cable (69) with a Cable Clip (74). Attach the other end - Weider 8300 Hard Drive | English Manual - Page 17
hard drive system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Follow the instructions See the back cover of this owner's manual for information about ordering replacement parts. Adjustment 69 Screw Ball 0 Adjustment - Weider 8300 Hard Drive | English Manual - Page 18
CABLING DIAGRAM The Pulley Cable (69) and Weight Cable (70) come pre-assembled. However, if either Cable has shifted during shipping, use the diagram below to make sure that the cable is properly routed. 0 69 High Pulley Station 0 0 Anchor Bolt Low Pulley Station To Weight Stack 70 18 - Weider 8300 Hard Drive | English Manual - Page 19
19 - Weider 8300 Hard Drive | English Manual - Page 20
2338 WG-8300). 2. The NAME of the product (WEIDER° 8300 Hard Drive System). 3. The SERIAL NUMBER of the product (see the front cover of this manual). 4. improper or abnormal usage or repairs not provided by a WEIDER authorized service center or for products used for commercial or rental purposes. - Weider 8300 Hard Drive | English Manual - Page 21
PART IDENTIFICATION CHART-Model No. WG83000 R894A This chart is provided to help identify the small parts used in assembly. The number in parenthesis below each part refers of the key number of the part. The second number refers to the quantity used in assembly. This side of the chart shows all of - Weider 8300 Hard Drive | English Manual - Page 22
1 1/2" Inner Cap (38)---4 1 3/4" Inner Cap (29)-8 2" Inner Cap (13)--4 Roller (109)-4 5/16" x 2 1/2" Eyebolt (37)-1 1 1" x 2" Inner Cap (114)-2 2" Outer Cap (127)-3 Part No. 121759 R894A Printed in CANADA© 1994 Weider, Inc. - Weider 8300 Hard Drive | English Manual - Page 23
0 1/2" x 3/8" Bushing (57)-5 1/2" x 7/16" Bushing (100)-1 1/2" x 5/16" Spacer (3)-2 0 3/4" Cover Cap (65)-4 1" Plastic Cap (51)-2 3/4" Round Cap (36)-4 1" Round Cap (43)-8 Rubber Bumper (9)-2 1" Retainer (50)-4 - Weider 8300 Hard Drive | English Manual - Page 24
1/4" x 2" Screw (82)-4 \\\ 10 5/16" x 3 1/4" Bolt (115)-3 5/16" x Bolt-(95)-2 3/8" x 3 1/4" Bolt (8)-2 1/4" x 2 1/4" Carriage Bolt (40)-3 1/4" x 2 1/4" Screw (120)-2 \\\\\\\1 O 5/16" x 2 1/4" Bolt (23)-4 5/16" x 2 3/4" Bolt (122)-6 O Do 5/16" x 2 3/4" Carriage Bolt (113)-2 1/4" - Weider 8300 Hard Drive | English Manual - Page 25
PART LIST Model No, WG83000 Key No. Qty. Description 1 8 5/16" x 2 1/2" Carriage Bolt 2 1 5/16" x 1 1/4" Bolt 3 2 1/2" x 5/16" Spacer 4 34 5/16" Nylon Locknut 5 14 1/4" Nylon Locknut 6 15 1/4" Flat Washer 7 12 1/4" x 3/4" Screw 8 3 3/8" x 3 1/4" Bolt 9 2 Rubber Bumper 10 7 #8-32 Screw 11 2 5/16" - Weider 8300 Hard Drive | English Manual - Page 26
Identification Chart # 1 Part List/Exploded Drawing Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the owner's manual for information about ordering replacement parts. Part No. 121759 R894A 1994 Weider, Inc., Printed in Canada - Weider 8300 Hard Drive | English Manual - Page 27
EXPLODED DRAWING Model No. WG83000 R894A 47 43 38 -AO 48 38 1 80 4 80 6 riN324 a 95 45 29 79 4 63 14 82 6 120 1 4 52 102 61 98 02 10 10 10 98 98 46 11 11545 QkV 116 64 tw ,93 57 23 88 13 90 fr-63 114 105 97 94 70 43 87 45 428 45 101 29 100 2„.110 122 66 65 3-: 5 4 - Weider 8300 Hard Drive | English Manual - Page 28
5 59 89 141 9 6 -41) 58 70 60 118 • 99 -c&,..> 83 81. 63 7 " -69 63 N83 92 91 77 117 63,41 • 91 5° 6(3_ 76 I 71 15 71 75 18 121 64 64 68 j 68 111 9 29 119 4 78 4 21 ) 4r- 45 55 122 30 22 14 106 5 4 25 26 5 0- 65 O 0 0 6 12 106 43 4 % 29 45 4 57 48 4 7 29
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
•A'
'
77
e" 674
'
ec;-
Q
77r4
'
7
"'"
—
'
MULTI
-STATION
•
PROFESSIONAL QUALITY FITNESS SYSTEM
Model
No.
WG83000
Serial
No.
0
0
Serial
Number
Decal
(Under
Seat)
QUESTIONS?
As
a
manufacturer,
we
are
com-
mitted
to
providing
complete
customer
satisfaction.
If
you
have
questions,
or
find
there
are
missing
or
damaged
parts,
we
will
guarantee
you
complete
satisfaction
through
direct
assistance
from
our
factory.
TO
AVOID
UNNECESSARY
DELAYS,
PLEASE
CALL
DIRECT
TO
OUR
TOLL
-FREE
CUSTOMER
HOT
LINE.
The
trained
technicians
on
our
customer
hot
line
will
provide
immediate
assistance,
free
of
charge
to
you.
CUSTOMER
HOT
LINE:
1-800-225-0653
Mon.
-Fri.,
6
a.m.-6
p.m.
MST
CAUTION!
Read
all
safety
precautions
and
instructions
in
this
owner's
manual
before
using
this
equip-
ment.
Save
this
owner's
manual
for
future
reference.
PATENT
PENDING
OWNER'S
MANUAL
•
•
0
0