Weider B120 Bench Assembly Instructions - Page 5

Pivot, Detail, Bracket, Brackets

Get Weider B120 Bench PDF manuals and user guides View all Weider B120 Bench manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

gullitopo. 9 0 0 DETAIL A 0 0 STEP 3 - ATTACHING BACKREST & SEAT I PIVOT ROD BACKREST: To aid in attaching backrest, first slide the BACKREST k p SEAT BRACKET ADJ. BAR (9) through one of the hole patterns in the uprights. With LONG ANGLE IRON (10) free, 0 lower BACKREST (5) to main frame pivot rod. Slide the secured LONG ANGLE IRON (10) onto one side of pivot rod. Swing the free LONG ANGLE IRON (10) back to its original position and onto the opposite end of the pivot rod. See Detail A. Replace MACHINE SCREW (k) that was removed in Step 2 and tighten all machine screws. SEAT: With SEAT (6) right-side up, lower SEAT (6) to seat brackets on main frame. Align bolt holes and fasten with 2 MACHINE SCREWS (k). Tighten al l machine screws. 0 4 0 LEG CURL BRACKETS 0 A OOP 0 7 0 STEP 4 - ATTACHING LEG CURL 0 I. Place LEG CURL (4) between leg curl 0 brackets on main frame and align bolt holes. Secure with HEX HEAD BOLT (f) •8 C and LOCK NUT (g). Repeat the following instructions until all PAD BARS (7) and FOAM PADS (8) are in place. First slide PAD. BAR (7) through proper hole in LEG CURL (4) until equal amounts of bar are on both sides of LEG CURL (4). Slide one FOAM PAD (8) onto each end of PAD BAR (7). Insert SQUARE PLASTIC CAP (e) into end of LEG CURL (4). Insert PLASTIC Cap (b) into weight pin on leg curl. Place COVER CAP (c) over weight pin opposite end. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
gullitopo.
9
STEP
3
-
ATTACHING
BACKREST
&
SEAT
0
0
I
PIVOT
ROD
k
DETAIL
A
BACKREST:
To
aid
in
attaching
backrest,
first
slide
the
BACKREST
p
SEAT
BRACKET
ADJ.
BAR
(9)
through
one
of
the
hole
patterns
in
the
uprights.
With
LONG
ANGLE
IRON
(10)
free,
lower
BACKREST
(5)
to
main
frame
pivot
rod.
Slide
the
secured
LONG
ANGLE
IRON
(10)
onto
one
side
of
pivot
rod.
Swing
the
free
LONG
ANGLE
IRON
(10)
back
to
its
original
position
and
onto
the
opposite
end
of
the
pivot
rod.
See
Detail
A.
Replace
MACHINE
SCREW
(k)
that
was
removed
in
Step
2
and
tighten
all
machine
screws.
SEAT:
With
SEAT
(6)
right
-side
up,
lower
SEAT
(6)
to
seat
brackets
on
main
frame.
Align
bolt
holes
and
fasten
with
2
MACHINE
SCREWS
(k).
Tighten
al
l
machine
screws.
0
0
0
0
LEG
CURL
BRACKETS
0
0
4
0
A
7
0
I.
OOP
0
0
STEP
4
-
ATTACHING
LEG
CURL
Place
LEG
CURL
(4)
between
leg
curl
brackets
on
main
frame
and
align
bolt
holes.
Secure
with
HEX
HEAD
BOLT
(f)
•
8
and
LOCK
NUT
(g).
Repeat
the
following
instructions
until
all
PAD
BARS
(7)
and
FOAM
PADS
(8)
are
in
place.
First
slide
PAD.
BAR
(7)
through
proper
hole
in
LEG
CURL
(4)
until
equal
amounts
of
bar
are
on
both
sides
of
LEG
CURL
(4).
Slide
one
FOAM
PAD
(8)
onto
each
end
of
PAD
BAR
(7).
Insert
SQUARE
PLASTIC
CAP
(e)
into
end
of
LEG
CURL
(4).
Insert
PLASTIC
Cap
(b)
into
weight
pin
on
leg
curl.
Place
COVER
CAP
(c)
over
weight
pin
opposite
end.
4
C