Weslo Cadence 60 Instruction Manual - Page 7
How To Fold And Move The Treadmill
View all Weslo Cadence 60 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Unplug the power cord. CAUTION: You must be able to safely lift 20 kg (45 lbs.) to raise, lower, or move the treadmill. 1. Hold the treadmill with your hands in the locations shown at the right. CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the treadmill until the frame passes the latch pin. Slowly release the latch knob. Make sure that the frame is securely held by the latch pin. To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F). HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch pin is fully inserted into the hole in the handrail and locked into place as described above. 1. Hold the handrails and place one foot on the base as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution whilst moving the treadmill. Do not attempt to move the treadmill over an uneven surface. 3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position. 14 Latch Knob Latch Pin Base Front Wheels 2. Open part bag B. Press the Right Frame Spacer (13) and the Left Frame Spacer (not shown) onto the sides of the Frame (55) as shown. Make sure that the high side of each Spacer is facing forward as shown. With the help of a second person, carefully lift the Frame (55) and hold the Spacers between the plates on the Uprights (89). Align the hole in the plate on the Right Upright (89) with the hole in the Right Frame Spacer (13). Loosely thread a 5" Bolt (10) and a 3/8" Star Washer (45) into the Spacer and the Frame (55). Repeat this step on the left side of the treadmill. See drawing 2a. With the help of a second person, carefully tip the treadmill onto its left side as shown. Feed the Wire Harness (22) into the large round hole near the lower end of the Right Upright (89), and then pull the Wire Harness out of the upper end as shown. 2 High side Plate 13 55 2a 89 22 45 89 10 22 3. Open part bag C. With the help of a second person, raise the Left and Right Uprights (88, 89) to the vertical position. Identify the Right Handrail (6), which has a large hole in the left side. Feed the Wire Harness (22) into the rectangular bracket on the Right Handrail and out of the large hole. (Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.) Press a Handrail Cap (83) onto the lower end of the Right Handrail as shown. Insert the rectangular bracket on the Right Handrail (6) into the right Upright (89). Attach the Right Handrail and the Handrail Cap (83) with three 1" Bolts (12) and two 1/4" Washers (108) as shown. Do not tighten the Bolts yet. Attach the Left Handrail (7) as described above. Note: There is not a wire harness on the left side. 3 7 12 108 12 12 108 88 83 22 Hole 12 6 108 12 89 83 12 7