Weslo Cadence Dx10 Canadian English Manual - Page 6

Assembly - instructions

Page 6 highlights

ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires your own phillips screw- driver , two adjustable wrenches , and scissors . 1. Note that the right Handrail and the Console Base (not shown) are connected to the treadmill by a Wire Harness. During assembly steps 1 through 5, be careful not to pull on or damage the Wire Harness. With the help of a second person, carefully lay the treadmill on its side. Position one of the Base Legs (38) on the base of the Upright (31) as shown. Make sure that the Base Leg Pads (41) and the Front Wheel (39) are in the indicated positions. Attach the Base Leg with two 3/8" x 2" Bolts (43), two 3/8" Washers (44) and two 3/8" Nuts (34). Carefully turn the treadmill onto its other side. Assemble the other Base Leg (38) as described. With the help of a second person, carefully raise the treadmill to the upright position so the Base Legs (38) are resting flat on the floor. 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 12. Follow the instructions in step 2 to lower the treadmill. Cut the plastic ties that hold the cage nuts in each Handrail (32). Position the left Handrail (32) on the left Upright (31). Thread a 1/4" x 1" Bolt (23) with a 1/4" Washer (22) two turns into the upper end of the left Upright and the left Handrail. Do not tighten the Bolt yet. Thread a 1/4" x 1" Bolt (23) with a 1/4" Washer (22) two turns into the lower end of the left Handrail (32) and the left Upright (31). Do not tighten the Bolt yet. 3. With the help of a second person, hold the Console Base (12) and the right Handrail (32) near the right Upright (31) as shown. Feed the excess Wire Harness (28) into the right Handrail (32) and then insert it down the right Upright. Next, insert the bracket on the right Handrail into the right Upright. Be careful not to pinch the Wire Harness. 1 39 31 34 43 44 41 38 2 23 22 32 31 22 23 3 12 Bracket 28 32 31 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23

6
1.
Note that the right Handrail and the Console Base
(not shown) are connected to the treadmill by a Wire
Harness.
During assembly steps 1 through 5, be
careful not to pull on or damage the Wire Harness.
With the help of a second person, carefully lay the
treadmill on its side. Position one of the Base Legs
(38) on the base of the Upright (31) as shown. Make
sure that the Base Leg Pads (41) and the Front
Wheel (39) are in the indicated positions. Attach the
Base Leg with two 3/8” x 2” Bolts (43), two 3/8”
Washers (44) and two 3/8” Nuts (34).
Carefully turn the treadmill onto its other side.
Assemble the other Base Leg (38) as described.
With the help of a second person, carefully raise the
treadmill to the upright position so the Base Legs
(38) are resting flat on the floor.
2.
Refer to HOW TO LOWER THE TREADMILL FOR
USE on page 12. Follow the instructions in step 2 to
lower the treadmill.
Cut the plastic ties that hold the cage nuts in each
Handrail (32).
Position the left Handrail (32) on the left Upright
(31). Thread a 1/4” x 1” Bolt (23) with a 1/4” Washer
(22) two turns into the upper end of the left Upright
and the left Handrail.
Do not tighten the Bolt yet.
Thread a 1/4” x 1” Bolt (23) with a 1/4” Washer (22)
two turns into the lower end of the left Handrail (32)
and the left Upright (31).
Do not tighten the Bolt
yet.
1
43
44
41
38
39
31
34
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires your own phillips screw-
driver
, two adjustable wrenches
, and scissors
.
22
23
2
32
31
22
3.
With the help of a second person, hold the Console
Base (12) and the right Handrail (32) near the right
Upright (31) as shown. Feed the excess Wire
Harness (28) into the right Handrail (32) and then
insert it down the right Upright. Next, insert the
bracket on the right Handrail into the right Upright.
Be careful not to pinch the Wire Harness.
28
Bracket
32
31
3
12
23