Weslo Cadence Ls 8 English Manual - Page 8

Caution

Get Weslo Cadence Ls 8 PDF manuals and user guides View all Weslo Cadence Ls 8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

DIAGRAM OF THE CONSOLE Monitor Display Pulse Display Speed Control Key Pulse Sensor Clip CAUTION: Before operating the console, read the following precautions. ¥ Do not stand on the walking belt when turning on the power. ¥ Always wear the clip (see the drawing above) while operating the treadmill. When the key is removed from the console, the walking belt will stop. ¥ Adjust the speed in small increments. ¥ The training zones marked below the speed control are general guidelines only. See page 14 or more information. ¥ To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and use only a sealable water bottle. STEP BY STEP CONSOLE OPERATION Before operating the console, make sure that the power cord is properly plugged in. (See HOW TO PLUG IN THE POWER CORD on page 7.) In addition, make sure that batteries are installed in the console. (See step 6 on page 6.) If there is a thin sheet of clear plastic on the console, remove it. Follow the steps below to operate the console. 1 Insert the key fully into the power switch. Inserting the key will not turn on the displays. The displays will turn on when the MODE button is pressed or when the walking belt is started. Note: If you just installed batteries, the displays will already be on. 2 Reset the console and start the walking belt. Move the speed control to the RESET position. Note: Each time the walking belt is stopped, the speed control must be moved to the RESET position before the walking belt can be restarted. Next, slowly move the speed control until the walking belt begins to move at slow speed. Carefully step onto the walking belt and begin exercising. Change the speed of the walking belt as desired by moving the speed control. Step onto the foot rails of the treadmill. Next, find the clip attached to the key (see the drawing above). Slide the clip onto your waistband. To stop the walking belt, step onto the foot rails and move the speed control to the RESET position. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
8
DIAGRAM OF THE CONSOLE
Clip
Key
Speed Control
Monitor Display
Pulse Display
Pulse Sensor
STEP BY STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) In addition,
make sure that batteries are installed in the console.
(See step 6 on page 6.) If there is a thin sheet of clear
plastic on the console, remove it.
Step onto the foot rails of the treadmill. Next, find the
clip attached to the key (see the drawing above). Slide
the clip onto your waistband.
Follow the steps below to operate the console.
Insert the key fully into the power switch.
Inserting the key will
not turn on the dis-
plays. The displays will
turn on when the
MODE button is
pressed or when the
walking belt is started.
Note: If you just
installed batteries, the displays will already be on.
Reset the console and start the walking belt.
Move the speed
control to the
RESET position.
Note: Each time
the walking belt
is stopped, the
speed control
must be moved to the RESET position before
the walking belt can be restarted.
Next, slowly move the speed control until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin
exercising. Change the speed of the walking belt
as desired by moving the speed control.
To stop the walking belt, step onto the foot rails
and move the speed control to the RESET position.
2
1
CAUTION:
Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
¥ Adjust the speed in small increments.
¥ The training zones marked below the speed
control are general guidelines only. See
page 14 or more information.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.