Whirlpool WED9371YL Installation Guide - Page 19

Level Dryer, Complete Installation, Checklist

Get Whirlpool WED9371YL PDF manuals and user guides View all Whirlpool WED9371YL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

LEVEL DRYER 1. Level dryer Place level here Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly Not Level LEVEL 2. Adjust leveling legs Not Level If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs are snug against the floor and the dryer does not rock. COMPLETE INSTALLATION CHECKLIST q Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. q Check that you have all of your tools. q Dispose of/recycle all packaging materials. q Check dryer's final location. Be sure vent is not crushed or kinked. q Check that dryer is level. See "Level Dryer". q Remove film on console and any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read "Dryer Use" in your Use and Care Guide. q For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on Power. Steam Models Only: q Be sure the water faucets are on (steam models only). q Check for leaks around "Y" connector, faucet, and hoses. q If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce product performance. Excessive scale buildup may lead to the need for certain part replacement or repair. All Models: q Select a Time Dry heated cycle, and start dryer. Do not select Air Only Temperature setting. If dryer will not start, check the following: • Controls are set in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into an outlet and/or electrical supply. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. This dryer automatically runs an installation diagnostic routine at the start of its first cycle. NOTE: You may notice an odor when dryer is first heated. This odor is common when heating element is first used. The odor will go away. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
19
2.
Adjust leveling legs
If dryer is not level, prop up using a wood block, use wrench
to adjust legs up or down, and check again for levelness.
Once dryer is level, make sure all four legs are snug against
the floor and the dryer does not rock.
LEVEL DRYER
1.
Level dryer
Place
level here
Check levelness of dryer from
side to side. Repeat from front to back.
NOTE:
The dryer must be level for the moisture sensing system
to operate correctly
Not Level
Not Level
LEVEL
COMPLETE INSTALLATION
CHECKLIST
q
Check that all parts are now installed. If there is an extra
part, go back through steps to see what was skipped.
q
Check that you have all of your tools.
q
Dispose of/recycle all packaging materials.
q
Check dryer’s final location. Be sure vent is not crushed
or kinked.
q
Check that dryer is level. See “Level Dryer”.
q
Remove film on console and any tape remaining on dryer.
q
Wipe dryer drum interior thoroughly with a damp cloth to
remove any dust.
q
Read “Dryer Use” in your Use and Care Guide.
q
For power supply cord installation, plug into a grounded
outlet. For direct wire installation, turn on Power.
Steam Models Only:
q
Be sure the water faucets are on (steam models only).
q
Check for leaks around “Y” connector, faucet, and hoses.
q
If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale through the
water system in the dryer. Over time, the buildup of lime
scale may clog different parts of the water system, which
will reduce product performance. Excessive scale buildup
may lead to the need for certain part replacement or repair.
All Models:
q
Select a Time Dry heated cycle, and start dryer. Do not
select Air Only Temperature setting.
If dryer will not start, check the following:
• Controls are set in a running or “On” position.
• Start button has been pushed firmly.
• Dryer is plugged into an outlet and/or electrical
supply.
• Household fuse is intact and tight, or circuit breaker
has not
tripped.
• Dryer door is closed.
This dryer automatically runs an installation diagnostic routine
at the start of its first cycle.
NOTE:
You may notice an odor when dryer is first heated.
This odor is common when heating element is first used.
The odor will go away.