Whirlpool WEG750H0H Instrucciones de instalacion - Page 4
Installation Requirements
View all Whirlpool WEG750H0H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■■ Tape measure ■■ Phillips screwdriver ■■ Flat-blade screwdriver ■■ 1/8" (3 mm) flat-blade screwdriver ■■ Pipe-joint compound resistant to propane gas ■■ 3/16" (4.8 mm) carbidetipped masonry drill bit (for concrete/ceramic floors) ■■ Level ■■ Drill ■■ Wrench or pliers ■■ Noncorrosive leakdetection solution For Propane/Natural Gas Conversions Optional Parts To purchase these or any other accessories, please reference the "Accessories" section of the User Guide for contact information. ■■ Side Trim Kits: 5/8" (15.88 mm) White - Order Part Number W10675027 5/8" (15.88 mm) Black - Order Part Number W10675026 5/8" (15.88 mm) Stainless Steel - Order Part Number W10675028 11/8" (2.9 cm) White - Order Part Number W10731885 1¹⁄8" (2.9 cm) Black - Order Part Number W10731886 1¹⁄8" (2.9 cm) Stainless Steel - Order Part Number W10731887 ■■ Backsplash Kits: High 6" (15.2 cm) White - Order Part Number W10655448 High 6" (15.2 cm) Black - Order Part Number W10655449 High 6" (15.2 cm) Stainless Steel - Order Part Number W10655450 ■■ Pipe wrench ■■ 15/16" (24 mm) combination wrench ■■ 1/8" (3.2 mm) drill bit (for wood floors) ■■ Marker or pencil ■■ 5/8" (16 mm) combination wrench ■■ 3/8" (95 mm) nut driver ■■ 9/32" (7 mm) nut driver ■■ Masking tape Parts Supplied Check that all parts are included. Location Requirements IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. ■■ It is the installer's responsibility to comply with installation clearances specified on the model/serial/rating plate. The model/serial/rating plate is located behind the oven door on the top right-hand side of the oven frame. ■■ The range should be located for convenient use in the kitchen. ■■ Propane/Natural Gas Conversion Kit ■■ #10 x 15/8" (41.3 mm) screws (for mounting anti-tip bracket) (2) ■■ Anti-tip bracket (inside oven cavity) Anti-tip bracket must be securely mounted to the back wall or floor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. ■■ For Models: Burner Caps WEG750H0H WEGA25H0H 5 ■■ Recessed installations must provide complete enclosure of the sides and rear of the range. ■■ All openings in the wall or floor where range is to be installed must be sealed. ■■ Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances. ■■ The anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see "Install Anti-Tip Bracket" section. ■■ Grounded electrical supply is required. See the "Electrical Requirements" section. ■■ Proper gas supply connection must be available. See the "Gas Supply Requirements" section. Burner Grates 2 Oven Racks 3 Parts Needed Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See the "Electrical Requirements" and "Gas Supply Requirements" sections. IMPORTANT: When the range is used under microwave models: JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door Baffle Plate Part Number W10737014 must be ordered and used. Please reference the "Accessories" section of the User Guide for contact information. ■■ Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C). ■■ Use an insulated pad or 1/4" (6.4 mm) plywood under range if installing range over carpeting. IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C). 4