Whirlpool WFE710H0AH Use & Care Guide - Page 16

Troubleshooting

Page 16 highlights

Oven Light The oven light is a standard 40-watt appliance bulb. Before replacing, make sure the oven and cooktop are cool and the control knobs are in the off position. 2. Turn the glass bulb cover in the back of the oven counterclockwise to remove. 3. Turn bulb counterclockwise to remove from socket. To Replace: 1. Unplug range or disconnect power. 4. Replace bulb, then bulb cover by turning clockwise. 5. Plug in range or reconnect power. TROUBLESHOOTING First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call. www.whirlpool.com Operation PROBLEM Nothing will operate Cooktop will not operate Excessive heat around cookware on cooktop Cooktop cooking results not what expected Oven will not operate Convection fan not working Oven temperature too high or too low Oven indicator lights flash Display shows messages POSSIBLE CAUSES Power supply cord is unplugged. Household fuse is blown or a circuit breaker is tripped. Range is in Sabbath Mode. The control knob is set incorrectly. The range is in Demo Mode. Cookware that is not the proper size Control knob set to incorrect heat level Range is not level. The electronic oven control was set incorrectly. Delay Start was set. The oven control lockout is set. The range is in Demo Mode. Oven door is open. Oven temperature calibration needs adjustment Temperature has been changed to Fahrenheit or Celsius. Needs service (oven indicator lights are flashing) Power failure (display shows flashing time) Error code (display shows letter followed by number) SOLUTIONS Plug into a grounded outlet. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. See "Sabbath Mode" section. Push in knob before turning to a setting. Demo Mode will deactivate the Warm Zone element. See "Demo Mode" in the "Electronic Oven Controls" section. Use cookware about the same size as the surface cooking area, element or surface burner. Cookware should not extend more than ½" (1.3 cm) outside the cooking area. See "Cooktop Use" section. Level the range. See the Installation Instructions. See "Electronic Oven Controls" section. See "Cook Time" section. See the control lock keypad feature in the "Feature Guide" section. Demo Mode will deactivate all heating elements. See "Demo Mode" in the "Electronic Oven Controls" section. Close oven door. See "Convection Cooking" section. See "Oven Temperature Control" in the "Electronic Oven Controls" section. See "Fahrenheit and Celsius" in the "Electronic Oven Controls" section. See "Control Display" in the "Electronic Oven Controls" section. If the indicator light(s) keeps flashing, call for service. See cover for contact information. Clear the display. On some models, reset the clock, if needed. See "Clock" keypad feature in the "Feature Guide" section. Press the CANCEL keypad to clear the display. See "Control Display" in the "Electronic Oven Controls" section. If it reappears, call for service. See cover for contact information. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

16
Oven Light
The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
To Replace:
1.
Unplug range or disconnect power.
2.
Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3.
Turn bulb counterclockwise to remove from socket.
4.
Replace bulb, then bulb cover by turning clockwise.
5.
Plug in range or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
www.whirlpool.com
Operation
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
Nothing will operate
Power supply cord is unplugged.
Plug into a grounded outlet.
Household fuse is blown or a
circuit breaker is tripped.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Range is in Sabbath Mode.
See “Sabbath Mode” section.
Cooktop will not operate
The control knob is set
incorrectly.
Push in knob before turning to a setting.
The range is in Demo Mode.
Demo Mode will deactivate the Warm Zone element. See
“Demo Mode” in the “Electronic Oven Controls” section.
Excessive heat around
cookware on cooktop
Cookware that is not the proper
size
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than ½" (1.3 cm) outside the cooking area.
Cooktop cooking results not
what expected
Control knob set to incorrect heat
level
See “Cooktop Use” section.
Range is not level.
Level the range. See the Installation Instructions.
Oven will not operate
The electronic oven control was
set incorrectly.
See “Electronic Oven Controls” section.
Delay Start was set.
See “Cook Time” section.
The oven control lockout is set.
See the control lock keypad feature in the “Feature Guide”
section.
The range is in Demo Mode.
Demo Mode will deactivate all heating elements. See “Demo
Mode” in the “Electronic Oven Controls” section.
Convection fan not working
Oven door is open.
Close oven door. See “Convection Cooking” section.
Oven temperature too high or
too low
Oven temperature calibration
needs adjustment
See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Temperature has been changed
to Fahrenheit or Celsius.
See “Fahrenheit and Celsius” in the “Electronic Oven Controls”
section.
Oven indicator lights flash
Needs service (oven indicator
lights are flashing)
See “Control Display” in the “Electronic Oven Controls”
section. If the indicator light(s) keeps flashing, call for service.
See cover for contact information.
Display shows messages
Power failure (display shows
flashing time)
Clear the display. On some models, reset the clock, if needed.
See “Clock” keypad feature in the “Feature Guide” section.
Error code (display shows letter
followed by number)
Press the CANCEL keypad to clear the display. See “Control
Display” in the “Electronic Oven Controls” section. If it
reappears, call for service. See cover for contact information.