Whirlpool WFG510S0AD Installation Guide - Page 16

To Convert Oven Bake Burner Natural Gas to LP Gas, To Convert Oven Broil Burner Natural Gas to LP

Get Whirlpool WFG510S0AD PDF manuals and user guides View all Whirlpool WFG510S0AD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

To Convert Oven Bake Burner (Natural Gas to LP Gas) 1. Remove the oven racks. 2. Remove 2 screws at the rear of the oven bottom. 3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. A 8. Replace the "49" spud with a "57" spud. Install the LP gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A B A. Screws B. Oven bottom 4. Remove 2 screws from the front tabs of the flame spreader. Lift front of the flame spreader and pull forward to remove tabs from rear of oven and set it aside on a covered surface. B A A. Screws B. Flame spreader 5. Remove 2 screws from the bake burner. 6. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, and set the bake burner aside. B A. Orifice spud 9. Position the back of the bake burner over the oven orifice, and slide the tab on front of the bake burner into the front of the oven. 10. Reattach the bake burner with 2 screws. 11. Insert the tabs on the rear of the flame spreader into the rear of the oven. 12. Reattach the front tabs of the flame spreader to the oven with 2 screws. 13. Position the front of the oven bottom panel toward the front frame and lower the rear of the oven bottom panel into the oven. 14. Reattach the oven bottom panel with 2 screws. To Convert Oven Broil Burner (Natural Gas to LP Gas) 1. Remove the screw from the broil burner. 2. Remove the broil burner from the broil burner orifice hood. NOTE: The broil burner will hang in the back of the oven while changing the orifice hood. B A A A. Screws B. Bake burner 7. Use a ³⁄₈" nut driver or combination wrench and turn the Natural gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "49." C A. Broil burner B. Screws C. Orifice hood 3. Use a ³⁄₈" combination wrench and turn the Natural gas broil burner orifice hood counterclockwise to remove. The hood will be stamped with a "53." 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
16
To Convert Oven Bake Burner (Natural Gas to LP Gas)
1.
Remove the oven racks.
2.
Remove 2 screws at the rear of the oven bottom.
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
4.
Remove 2 screws from the front tabs of the flame spreader.
Lift front of the flame spreader and pull forward to remove
tabs from rear of oven and set it aside on a covered surface.
5.
Remove 2 screws from the bake burner.
6.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, and set the bake burner aside.
7.
Use a
³⁄₈
" nut driver or combination wrench and turn the
Natural gas bake burner orifice spud counterclockwise to
remove. The spud will be stamped with a “49.”
8.
Replace the “49” spud with a “57” spud. Install the LP gas
bake burner orifice spud, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
9.
Position the back of the bake burner over the oven orifice,
and slide the tab on front of the bake burner into the front of
the oven.
10.
Reattach the bake burner with 2 screws.
11.
Insert the tabs on the rear of the flame spreader into the rear
of the oven.
12.
Reattach the front tabs of the flame spreader to the oven with
2 screws.
13.
Position the front of the oven bottom panel toward the front
frame and lower the rear of the oven bottom panel into the
oven.
14.
Reattach the oven bottom panel with 2 screws.
To Convert Oven Broil Burner (Natural Gas to LP Gas)
1.
Remove the screw from the broil burner.
2.
Remove the broil burner from the broil burner orifice hood.
NOTE:
The broil burner will hang in the back of the oven while
changing the orifice hood.
3.
Use a
³⁄₈
" combination wrench and turn the Natural gas broil
burner orifice hood counterclockwise to remove. The hood
will be stamped with a “53.”
A. Screws
B. Oven bottom
A. Screws
B. Flame spreader
A. Screws
B. Bake burner
A
B
A
B
A
B
A. Orifice spud
A. Broil burner
B. Screws
C. Orifice hood
A
B
C
A