Whirlpool WFG515S0J Installation Instructions - Page 20

To Convert Oven Bake Burner Propane Gas to, Natural Gas

Get Whirlpool WFG515S0J PDF manuals and user guides View all Whirlpool WFG515S0J manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Refer to the following chart for the correct Natural gas orifice spud placement. Natural Gas Orifice Spud Chart Burner Rating Size (mm) ID Number 18,000 BTU 2.00 200AM 17,000 BTU 1.96 196AM 15,000 BTU 1.80 180AM 9,500 BTU 1.40 140AM 8,000 BTU 1.30 130AM 5,000 BTU 1.00 100AM NOTE: Refer to the model/serial/rating plate located on the oven frame behind the top right-hand side of the oven door for proper sizing of spuds for each burner location. 5. Place propane gas orifice spuds in the orifice spud bag. IMPORTANT: Keep the propane gas orifice spuds in case of reinstallation with propane gas. 6. Replace the burner base. 7. Replace burner cap. 8. Repeat steps 1 to 7 for the remaining burners. To Convert Oven Bake Burner (Propane Gas to Natural Gas) 1. Remove the oven racks. 2. Remove 2 screws at the rear of the oven bottom. 3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. 6. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, and set the bake burner aside. B A A. Screws B. Bake burner 7. Use a 3/8" (1 cm) nut driver or combination wrench and turn the Propane gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "57." 8. Replace the "57" spud with a "51" spud. Install the Natural gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A A B A. Screws B. Oven bottom 4. Remove 2 screws from the front tabs of the flame spreader. Lift front of the flame spreader and pull forward to remove tabs from rear of oven and set it aside on a covered surface. B A. Orifice spud 9. Position the back of the bake burner over the oven orifice, and slide the tab on front of the bake burner into the front of the oven. 10. Reattach the bake burner with 2 screws. 11. Insert the tabs on the rear of the flame spreader into the rear of the oven. 12. Reattach the front tabs of the flame spreader to the oven with 2 screws. 13. Position the front of the oven bottom panel toward the front frame and lower the rear of the oven bottom panel into the oven. 14. Reattach the oven bottom panel with 2 screws. A A. Screws B. Flame spreader 5. Remove 2 screws from the bake burner. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
20
Refer to the following chart for the correct Natural gas orifice
spud placement.
Natural Gas Orifice Spud Chart
Burner Rating
Size (mm)
ID Number
18,000 BTU
2.00
200AM
17,000 BTU
1.96
196AM
15,000 BTU
1.80
180AM
9,500 BTU
1.40
140AM
8,000 BTU
1.30
130AM
5,000 BTU
1.00
100AM
NOTE:
Refer to the model/serial/rating plate located on the oven
frame behind the top right-hand side of the oven door for proper
sizing of spuds for each burner location.
5.
Place propane gas orifice spuds in the orifice spud bag.
IMPORTANT:
Keep the propane gas orifice spuds in case
of reinstallation with propane gas.
6.
Replace the burner base.
7.
Replace burner cap.
8.
Repeat steps 1 to 7 for the remaining burners.
To Convert Oven Bake Burner (Propane Gas to
Natural Gas)
1.
Remove the oven racks.
2.
Remove 2 screws at the rear of the oven bottom.
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
4.
Remove 2 screws from the front tabs of the flame spreader.
Lift front of the flame spreader and pull forward to remove
tabs from rear of oven and set it aside on a covered surface.
5.
Remove 2 screws from the bake burner.
6.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, and set the bake burner aside.
7.
Use a 3/8" (1 cm) nut driver or combination wrench and turn
the Propane gas bake burner orifice spud counterclockwise
to remove. The spud will be stamped with a “57.”
8.
Replace the “57” spud with a “51” spud. Install the Natural
gas bake burner orifice spud, turning it clockwise until snug.
IMPORTANT
: Do not overtighten.
9.
Position the back of the bake burner over the oven orifice,
and slide the tab on front of the bake burner into the front of
the oven.
10.
Reattach the bake burner with 2 screws.
11.
Insert the tabs on the rear of the flame spreader into the rear
of the oven.
12.
Reattach the front tabs of the flame spreader to the oven
with 2 screws.
13.
Position the front of the oven bottom panel toward the front
frame and lower the rear of the oven bottom panel into the
oven.
14.
Reattach the oven bottom panel with 2 screws.
A
B
A. Screws
B. Oven bottom
A
B
A. Screws
B. Flame spreader
A
B
A. Screws
B. Bake burner
A
A. Orifice spud