Whirlpool WFG525S0HV Installation Instructions - Page 16

To Convert Surface Burners Natural Gas to Propane, To Convert Oven Bake Burner Natural Gas to,

Get Whirlpool WFG525S0HV PDF manuals and user guides View all Whirlpool WFG525S0HV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

3. Remove plastic cover from gas pressure regulator cap. 4. Turn gas pressure regulator cap counterclockwise with a 5/8" (1.6 cm) combination wrench to remove. NOTE: Do not remove the spring beneath the cap. Side view before A NG NG B D E A B C D A. Orifice spud B. Orifice spud holder C. Screw D. Spark electrode 4. Remove the cardboard orifice spud holder shipped in the literature package in the oven. Gas orifice spuds are stamped with a number, marked with 1 color dot, and have a groove in the hex area. Replace the Natural gas orifice spud with the correct Propane gas orifice spud. LP LP C Side view after A. Plastic cover B. Gas pressure regulator cap with solid end facing out C. Gas pressure regulator cap with hollow end facing out D. Washer E. Gas pressure regulator cap 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the hollow end faces out and the marking " LP" is facing the direction shown in the above drawing. 6. Replace plastic cover over gas pressure regulator cap. To Convert Surface Burners (Natural Gas to Propane Gas) 1. Remove burner cap. 2. Using a Phillips or Quadrex® screwdriver, remove the burner base. NOTE: Reinstall one of the screws through the range cooktop to hold the orifice spud holder in place while removing and replacing the orifice spuds. C A D B A. Igniter electrode C. Burner cap B. Gas tube opening D. Burner base 3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. 16 A A. Propane groove Refer to the following chart for correct Propane gas orifice spud placement. Propane Gas Orifice Spud Chart for Surface Burner Burner Rating Color Size ID Number 14,000/14,200 BTU Yellow/Orange 1.16 mm L116 11,000 BTU Yellow/Brown 0.99 mm L99 8,000 BTU (round) Yellow/Black 0.88 mm L88 8,000 BTU (oval) Red/Orange 0.85 mm 85 5,000 BTU Yellow/White 0.70 mm L70 NOTE: Refer to the Model Number and Serial Number Plate located on the oven frame behind the top left side of the oven door for proper sizing of spuds for each burner location. 5. Place Natural gas orifice spuds in the cardboard orifice spud holder. 6. Replace the burner base using both screw. 7. Replace burner cap. 8. Repeat steps 1-7 for the remaining burners. To Convert Oven Bake Burner (Natural Gas to Propane Gas) 1. Remove the oven racks. 2. Remove 2 screws at the rear of the oven bottom. 3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. A B A. Screws B. Oven bottom

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
16
3.
Remove plastic cover from gas pressure regulator cap.
4.
Turn gas pressure regulator cap counterclockwise with a
5/8" (1.6 cm) combination wrench to remove.
NOTE
: Do not remove the spring beneath the cap.
5.
Turn over the gas pressure regulator cap and reinstall on
regulator so that the hollow end faces out and the marking
“
LP” is facing the direction shown in the above drawing.
6.
Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Natural Gas to Propane
Gas)
1.
Remove burner cap.
2.
Using a Phillips or Quadrex
®
screwdriver, remove the burner
base.
NOTE
: Reinstall one of the screws through the range
cooktop to hold the orifice spud holder in place while
removing and replacing the orifice spuds.
3.
Apply masking tape to the end of a 9/32" (7 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning it counterclockwise and lifting out.
Set gas orifice spud aside.
4.
Remove the cardboard orifice spud holder shipped in the
literature package in the oven. Gas orifice spuds are
stamped with a number, marked with 1 color dot, and have a
groove in the hex area. Replace the Natural gas orifice spud
with the correct Propane gas orifice spud.
Refer to the following chart for correct Propane gas orifice
spud placement.
Propane Gas Orifice Spud Chart for Surface Burner
Burner Rating
Color
Size
ID Number
14,000/14,200 BTU
Yellow/Orange
1.16 mm
L116
11,000 BTU
Yellow/Brown
0.99 mm
L99
8,000 BTU (round)
Yellow/Black
0.88 mm
L88
8,000 BTU (oval)
Red/Orange
0.85 mm
85
5,000 BTU
Yellow/White
0.70 mm
L70
NOTE:
Refer to the Model Number and Serial Number Plate
located on the oven frame behind the top left side of the oven
door for proper sizing of spuds for each burner location.
5.
Place Natural gas orifice spuds in the cardboard orifice spud
holder.
6.
Replace the burner base using both screw.
7.
Replace burner cap.
8.
Repeat steps 1-7 for the remaining burners.
To Convert Oven Bake Burner (Natural Gas to
Propane Gas)
1.
Remove the oven racks.
2.
Remove 2 screws at the rear of the oven bottom.
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
A
B
C
D
Side view before
Side view after
E
NG
LP
NG
LP
A. Plastic cover
B. Gas pressure regulator cap with solid end facing out
C. Gas pressure regulator cap with hollow end facing out
D. Washer
E. Gas pressure regulator cap
A
B
C
D
A. Igniter electrode
B. Gas tube opening
C. Burner cap
D. Burner base
B
A
C
D
A. Orifice spud
B. Orifice spud holder
C. Screw
D. Spark electrode
A
A. Propane groove
A
B
A. Screws
B. Oven bottom
°