Whirlpool WOC95EC0A Installation Instructions - Page 8

Install Warming Drawer Deflector Kit only, for ovens installed above warming, drawers

Get Whirlpool WOC95EC0A PDF manuals and user guides View all Whirlpool WOC95EC0A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

IMPORTANT: If the grommet is not installed, the front frame will be damaged. A ■ Using one #8-18 x 3/8" screw (D) on each side of the vent tab (B), fasten the vent securely to the oven. B A C B A. Mounting rail B. Mounting rail hole C. Grommet 5. Securely fasten oven to cabinet using the #8-14 x ³⁄₄" screws provided. Insert the screws through hole in the grommet. Do not overtighten screws. 6. For models KEMS379B and KEMS309B, see the following instructions. For all other models, the black front trims can be ordered as an accessory. Please reference the "Assistance or Service" section of the Use and Care Guide or contact the dealer from whom you purchased your built-in oven to order part numbers W10344482 and W10344483. ■ Remove the tape from black front trims. ■ Securely fasten the oven to the cabinet using the #8-14 x ¾" screws provided. ■ Insert the screws through hole in black trim aligning with hole in oven frame. Do not overtighten screws. A B D C A. Oven frame B. Vent tab C. Bottom vent D. #8-18 x ³⁄₈" screws 8. Replace oven racks. 9. Replace the oven door. See the "Replace Oven Door(s)" section. 10. Check that door is free to open and close. If it is not, repeat the removal and installation procedures. See "Prepare Built-In Microwave/Oven Combination" section. 11. Reconnect power. 12. The display panel will light briefly, and "PF" should appear in the display. 13. If the display panel does not light, please reference the "Assistance or Service" section of the Use and Care Guide or contact the dealer from whom you purchased your oven. Install Warming Drawer Deflector Kit (only for ovens installed above warming drawers) On combo microwave/oven models installed above a warming drawer, a warming drawer deflector kit must be installed. See the "Tools and Parts" section for information on ordering. Parts Supplied A C A. Oven frame B. Oven frame hole C. Black trim piece 7. The bottom vent is shipped in the foam packing at the top of the oven. Install the bottom vent (C) as follows: ■ Align vent tab (B) with oven frame (A) as shown. B A. Phillips head screws (4) only 2 screws for 27" (68.6 cm) size B. Warming drawer deflector (1) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
8
IMPORTANT:
If the grommet is not installed, the front frame
will be damaged.
5.
Securely fasten oven to cabinet using the #8–14 x
³⁄₄
" screws
provided. Insert the screws through hole in the grommet. Do
not overtighten screws.
6.
For models KEMS379B and KEMS309B, see the following
instructions.
For all other models, the black front trims can be ordered as
an accessory.
Please reference the “Assistance or Service”
section of the Use and Care Guide or contact the dealer from
whom you purchased your built-in oven to order part
numbers W10344482 and W10344483.
■
Remove the tape from black front trims.
■
Securely fasten the oven to the cabinet using the #8-14 x
¾" screws provided.
■
Insert the screws through hole in black trim aligning with
hole in oven frame. Do not overtighten screws.
7.
The bottom vent is shipped in the foam packing at the top of
the oven. Install the bottom vent (C) as follows:
■
Align vent tab (B) with oven frame (A) as shown.
■
Using one #8-18 x 3/8" screw (D) on each side of the vent
tab (B), fasten the vent securely to the oven.
8.
Replace oven racks.
9.
Replace the oven door. See the “Replace Oven Door(s)”
section.
10.
Check that door is free to open and close. If it is not, repeat
the removal and installation procedures. See “Prepare Built-In
Microwave/Oven Combination” section.
11.
Reconnect power.
12.
The display panel will light briefly, and “PF” should appear in
the display.
13.
If the display panel does not light, please reference the
“Assistance or Service” section of the Use and Care Guide or
contact the dealer from whom you purchased your oven.
Install Warming Drawer Deflector Kit (only
for ovens installed above warming
drawers)
On combo microwave/oven models installed above a warming
drawer, a warming drawer deflector kit must be installed. See the
“Tools and Parts” section for information on ordering.
Parts Supplied
A. Mounting rail
B. Mounting rail hole
C. Grommet
A. Oven frame
B. Oven frame hole
C. Black trim piece
A
B
C
A
B
C
A. Oven frame
B. Vent tab
C. Bottom vent
D. #8-18 x
³⁄₈
" screws
A. Phillips head screws (4)
only 2 screws for 27" (68.6 cm) size
B. Warming drawer deflector (1)
A
C
D
B
B
A