Whirlpool WOCA7EC0H Installation Instructions - Page 7

Install Oven, Install Deflector Kit Bracket

Get Whirlpool WOCA7EC0H PDF manuals and user guides View all Whirlpool WOCA7EC0H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Install Oven 1. Using 2 or more people, lift the oven partially into the cabinet cutout. Use the oven opening as an area to grip. NOTE: When pushing the microwave oven into the cabinet, open the microwave oven door and push against the seal area on the front frame. Do not push against the outside edges. Install Deflector Kit Bracket This assembly is required for use when a single or double built-in oven is installed in a flush installation. 1. Flex the upper vent piece (C) away from the lower vent piece (D) to slide the deflector bracket (B) between them. Some force may be required to flex the upper vent trim (C) away from the lower vent trim (D). Some force may also be required to flex the deflector bracket (B) and slide it into position. Make sure screw holes are properly aligned between the two pieces. See the following illustration. 2. Install the deflector bracket (B) to the lower vent piece (D) using two #8-18 x 1/4" screws on each side. NOTE: On 27" (68.6 cm) models, only one #8-18 x 1/4" screw is used on each side. A B C 2. Push against the front frame of the microwave oven to push oven into cabinet. B D A. #8-18 x 1/4" screws B. Deflector bracket C D C. Upper vent piece (supplied with oven) D. Lower vent piece (supplied with oven) 3. Align vent tab (B) with oven frame (A) as shown. 4. Using one #8-18 x 3/8" screw (E) on each side of the vent tab (B), fasten the vent securely to the oven. 3. Push the oven completely into the cabinet and center the oven into the cabinet cutout. 4. Remove the tape from the black front trim piece. ■■ Securely fasten the oven to the cabinet using the #8‑14 x 3/4" screws provided. ■■ Insert the screws through the hole in the black trim piece, aligning with the hole in the oven frame. Do not overtighten the screws. A B C A. Oven frame B. Oven frame hole C. Black trim piece A B E D A. Oven frame B. Vent tab C. Oven vent C D. Deflector bracket E. #8-18 x 3/8" screw 5. Replace the oven racks. 6. Replace the oven door. See the "Replace Oven Door" section. 7. Check that the door is free to open and close. If it is not, repeat the removal and installation procedures. See the "Prepare Built-In Oven" section. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
7
Install Oven
1.
Using 2 or more people, lift the oven partially into the cabinet
cutout. Use the oven opening as an area to grip.
NOTE:
When pushing the microwave oven into the cabinet,
open the microwave oven door and push against the seal
area on the front frame. Do not push against the outside
edges.
2.
Push against the front frame of the microwave oven to push
oven into cabinet.
3.
Push the oven completely into the cabinet and center the
oven into the cabinet cutout.
4.
Remove the tape from the black front trim piece.
■
Securely fasten the oven to the cabinet using the
#8-14 x 
3
/
4
" screws provided.
■
Insert the screws through the hole in the black trim
piece, aligning with the hole in the oven frame. Do not
overtighten the screws.
Install Deflector Kit Bracket
This assembly is required for use when a single or double
built-in oven is installed in a flush installation.
1.
Flex the upper vent piece (C) away from the lower vent
piece (D) to slide the deflector bracket (B) between them.
Some force may be required to flex the upper vent trim (C)
away from the lower vent trim (D). Some force may also
be required to flex the deflector bracket (B) and slide it
into position. Make sure screw holes are properly aligned
between the two pieces. See the following illustration.
2.
Install the deflector bracket (B) to the lower vent piece (D)
using two #8-18 x
1
/
4
" screws on each side.
NOTE:
On 27" (68.6 cm) models, only one #8-18 x
1
/
4
"
screw is used on each side.
3.
Align vent tab (B) with oven frame (A) as shown.
4.
Using one #8-18 x
3
/
8
" screw (E) on each side of the vent
tab (B), fasten the vent securely to the oven.
5.
Replace the oven racks.
6.
Replace the oven door. See the “Replace Oven Door”
section.
7.
Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Oven” section.
A. Oven frame
B. Oven frame hole
C. Black trim piece
A
B
C
D
B
A
C
B
D
C
A. #8–18 x
1
/
4
" screws
B. Deflector bracket
C. Upper vent piece (supplied with oven)
D. Lower vent piece (supplied with oven)
D. Deflector bracket
E. #8–18 x
3
/
8
" screw
A. Oven frame
B. Vent tab
C. Oven vent
A
C
D
B
E